dmesg - nvidia_opengl_linux
microcode: microcode updated early to revision 0x28, date = 2019-11-12
Linux version 5.4.0-53-generic (buildd@lcy01-amd64-007) (gcc version 9.3.0 (Ubuntu 9.3.0-17ubuntu1~20.04)) #59-Ubuntu SMP Wed Oct 21 09:38:44 UTC 2020 (Ubuntu 5.4.0-53.59-generic 5.4.65)
Command line: BOOT_IMAGE=/vmlinuz-5.4.0-53-generic root=/dev/mapper/vgubuntu-root ro quiet splash vt.handoff=7
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Hygon HygonGenuine
Centaur CentaurHauls
zhaoxin Shanghai
x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
BIOS-e820: [mem 0x0000000000059000-0x0000000000097fff] usable
BIOS-e820: [mem 0x0000000000098000-0x000000000009ffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000002cb7efff] usable
BIOS-e820: [mem 0x000000002cb7f000-0x000000002de7efff] reserved
BIOS-e820: [mem 0x000000002de7f000-0x000000002df7efff] ACPI NVS
BIOS-e820: [mem 0x000000002df7f000-0x000000002dffefff] ACPI data
BIOS-e820: [mem 0x000000002dfff000-0x000000002dffffff] usable
BIOS-e820: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000ff810000-0x00000000ff82efff] reserved
BIOS-e820: [mem 0x0000000100000000-0x00000008aedfffff] usable
NX (Execute Disable) protection: active
e820: update [mem 0x21348018-0x21373c57] usable ==> usable
e820: update [mem 0x21348018-0x21373c57] usable ==> usable
e820: update [mem 0x21337018-0x21347057] usable ==> usable
e820: update [mem 0x21337018-0x21347057] usable ==> usable
extended physical RAM map:
reserve setup_data: [mem 0x0000000000000000-0x0000000000057fff] usable
reserve setup_data: [mem 0x0000000000058000-0x0000000000058fff] reserved
reserve setup_data: [mem 0x0000000000059000-0x0000000000097fff] usable
reserve setup_data: [mem 0x0000000000098000-0x000000000009ffff] reserved
reserve setup_data: [mem 0x0000000000100000-0x0000000021337017] usable
reserve setup_data: [mem 0x0000000021337018-0x0000000021347057] usable
reserve setup_data: [mem 0x0000000021347058-0x0000000021348017] usable
reserve setup_data: [mem 0x0000000021348018-0x0000000021373c57] usable
reserve setup_data: [mem 0x0000000021373c58-0x000000002cb7efff] usable
reserve setup_data: [mem 0x000000002cb7f000-0x000000002de7efff] reserved
reserve setup_data: [mem 0x000000002de7f000-0x000000002df7efff] ACPI NVS
reserve setup_data: [mem 0x000000002df7f000-0x000000002dffefff] ACPI data
reserve setup_data: [mem 0x000000002dfff000-0x000000002dffffff] usable
reserve setup_data: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
reserve setup_data: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
reserve setup_data: [mem 0x00000000ff810000-0x00000000ff82efff] reserved
reserve setup_data: [mem 0x0000000100000000-0x00000008aedfffff] usable
efi: EFI v2.31 by HPQ
efi: ACPI=0x2dffe000 ACPI 2.0=0x2dffe014 SMBIOS=0x2d333118
secureboot: Secure boot disabled
SMBIOS 2.7 present.
DMI: Hewlett-Packard HP ZBook 15/1909, BIOS L70 Ver. 01.42 05/21/2018
tsc: Fast TSC calibration using PIT
tsc: Detected 2394.438 MHz processor
e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
last_pfn = 0x8aee00 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 00FF800000 mask 7FFF800000 write-protect
1 base 0000000000 mask 7FC0000000 write-back
2 base 0030000000 mask 7FF0000000 uncachable
3 base 002F000000 mask 7FFF000000 uncachable
4 base 0100000000 mask 7F00000000 write-back
5 base 0200000000 mask 7E00000000 write-back
6 base 0400000000 mask 7C00000000 write-back
7 base 0800000000 mask 7F80000000 write-back
8 base 0880000000 mask 7FC0000000 write-back
9 base 08B0000000 mask 7FF0000000 uncachable
x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
last_pfn = 0x2e000 max_arch_pfn = 0x400000000
check: Scanning 1 areas for low memory corruption
Using GB pages for direct mapping
secureboot: Secure boot disabled
RAMDISK: [mem 0x11eea000-0x17d3efff]
ACPI: Early table checksum verification disabled
ACPI: RSDP 0x000000002DFFE014 000024 (v02 HPQOEM)
ACPI: XSDT 0x000000002DFFE120 0000A4 (v01 HPQOEM SLIC-MPC 00000001 01000013)
ACPI: FACP 0x000000002DFFC000 00010C (v05 HPQOEM 1909 00000001 HP 00000001)
ACPI: DSDT 0x000000002DFD1000 02591A (v02 HPQOEM 1909 00000001 INTL 20110112)
ACPI: FACS 0x000000002DDE4000 000040
ACPI: FACS 0x000000002DDE4000 000040
ACPI: HPET 0x000000002DFFB000 000038 (v01 HPQOEM 1909 00000001 HP 00000001)
ACPI: APIC 0x000000002DFFA000 0000BC (v01 HPQOEM 1909 00000001 HP 00000001)
ACPI: MCFG 0x000000002DFF9000 00003C (v01 HPQOEM 1909 00000001 HP 00000001)
ACPI: TCPA 0x000000002DFF7000 000032 (v02 HPQOEM 1909 00000000 HP 00000001)
ACPI: SSDT 0x000000002DFCE000 000466 (v01 HPQOEM SataAhci 00001000 INTL 20110112)
ACPI: SSDT 0x000000002DFCD000 00048A (v01 HPQOEM PtidDevc 00001000 INTL 20110112)
ACPI: SLIC 0x000000002DFCC000 000176 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001)
ACPI: FPDT 0x000000002DFCA000 000044 (v01 HPQOEM 1909 00000001 HP 00000001)
ACPI: BGRT 0x000000002DFC9000 000038 (v00 HPQOEM 1909 00000001 HP 00000001)
ACPI: SSDT 0x000000002DFC3000 000544 (v01 PmRef Cpu0Ist 00003000 INTL 20110112)
ACPI: SSDT 0x000000002DFC2000 000AF3 (v01 PmRef CpuPm 00003000 INTL 20110112)
ACPI: SSDT 0x000000002DFC1000 0001D5 (v01 PmRef LakeTiny 00003000 INTL 20110112)
ACPI: SSDT 0x000000002DFC0000 000706 (v01 SaSsdt SaSsdt 00003000 INTL 20110112)
ACPI: SSDT 0x000000002DFBD000 002F28 (v01 HP NVSGTBL 00001000 INTL 20110112)
ACPI: ASF! 0x000000002DFF8000 0000A5 (v32 HPQOEM 1909 00000001 HP 00000001)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at [mem 0x0000000000000000-0x00000008aedfffff]
NODE_DATA(0) allocated [mem 0x8aedd5000-0x8aedfffff]
Zone ranges:
DMA [mem 0x0000000000001000-0x0000000000ffffff]
DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
Normal [mem 0x0000000100000000-0x00000008aedfffff]
Device empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000001000-0x0000000000057fff]
node 0: [mem 0x0000000000059000-0x0000000000097fff]
node 0: [mem 0x0000000000100000-0x000000002cb7efff]
node 0: [mem 0x000000002dfff000-0x000000002dffffff]
node 0: [mem 0x0000000100000000-0x00000008aedfffff]
Zeroed struct page in unavailable ranges: 18154 pages
Initmem setup node 0 [mem 0x0000000000001000-0x00000008aedfffff]
On node 0 totalpages: 8239382
DMA zone: 64 pages used for memmap
DMA zone: 1072 pages reserved
DMA zone: 3990 pages, LIFO batch:0
DMA32 zone: 2798 pages used for memmap
DMA32 zone: 179072 pages, LIFO batch:63
Normal zone: 125880 pages used for memmap
Normal zone: 8056320 pages, LIFO batch:63
Reserving Intel graphics memory at [mem 0x2f200000-0x4f1fffff]
ACPI: PM-Timer IO Port: 0x1808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
efi_bgrt: Ignoring BGRT: null image address
TSC deadline timer available
smpboot: Allowing 8 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
PM: Registered nosave memory: [mem 0x00098000-0x0009ffff]
PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
PM: Registered nosave memory: [mem 0x21337000-0x21337fff]
PM: Registered nosave memory: [mem 0x21347000-0x21347fff]
PM: Registered nosave memory: [mem 0x21348000-0x21348fff]
PM: Registered nosave memory: [mem 0x21373000-0x21373fff]
PM: Registered nosave memory: [mem 0x2cb7f000-0x2de7efff]
PM: Registered nosave memory: [mem 0x2de7f000-0x2df7efff]
PM: Registered nosave memory: [mem 0x2df7f000-0x2dffefff]
PM: Registered nosave memory: [mem 0x2e000000-0x2f1fffff]
PM: Registered nosave memory: [mem 0x2f200000-0x4f1fffff]
PM: Registered nosave memory: [mem 0x4f200000-0xe00f7fff]
PM: Registered nosave memory: [mem 0xe00f8000-0xe00f8fff]
PM: Registered nosave memory: [mem 0xe00f9000-0xfed1bfff]
PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
PM: Registered nosave memory: [mem 0xfed20000-0xff80ffff]
PM: Registered nosave memory: [mem 0xff810000-0xff82efff]
PM: Registered nosave memory: [mem 0xff82f000-0xffffffff]
[mem 0x4f200000-0xe00f7fff] available for PCI devices
Booting paravirtualized kernel on bare hardware
clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
percpu: Embedded 54 pages/cpu s184320 r8192 d28672 u262144
pcpu-alloc: s184320 r8192 d28672 u262144 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 4 5 6 7
Built 1 zonelists, mobility grouping on. Total pages: 8109568
Policy zone: Normal
Kernel command line: BOOT_IMAGE=/vmlinuz-5.4.0-53-generic root=/dev/mapper/vgubuntu-root ro quiet splash vt.handoff=7
Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear)
Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
mem auto-init: stack:off, heap alloc:on, heap free:off
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 32053572K/32957528K available (14339K kernel code, 2398K rwdata, 4956K rodata, 2716K init, 4988K bss, 903956K reserved, 0K cma-reserved)
random: get_random_u64 called from kmem_cache_open+0x2d/0x410 with crng_init=0
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Kernel/User page tables isolation: enabled
ftrace: allocating 44527 entries in 174 pages
rcu: Hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
NR_IRQS: 524544, nr_irqs: 488, preallocated irqs: 16
random: crng done (trusting CPU's manufacturer)
vt handoff: transparent VT on vt#7
Console: colour dummy device 80x25
printk: console [tty0] enabled
ACPI: Core revision 20190816
clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
APIC: Switch to symmetric I/O mode setup
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2283b158ace, max_idle_ns: 440795323119 ns
Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.87 BogoMIPS (lpj=9577752)
pid_max: default: 32768 minimum: 301
LSM: Security Framework initializing
Yama: becoming mindful.
AppArmor: AppArmor initialized
Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
*** VALIDATE tmpfs ***
*** VALIDATE proc ***
*** VALIDATE cgroup1 ***
*** VALIDATE cgroup2 ***
mce: CPU0: Thermal monitoring enabled (TM1)
process: using mwait in idle threads
Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
Spectre V2 : Mitigation: Full generic retpoline
Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
Spectre V2 : Enabling Restricted Speculation for firmware calls
Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
Spectre V2 : User space: Mitigation: STIBP via seccomp and prctl
Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
SRBDS: Mitigation: Microcode
MDS: Mitigation: Clear CPU buffers
Freeing SMP alternatives memory: 40K
smpboot: CPU0: Intel(R) Core(TM) i7-4700MQ CPU @ 2.40GHz (family: 0x6, model: 0x3c, stepping: 0x3)
Performance Events: PEBS fmt2+, Haswell events, 16-deep LBR, full-width counters, Intel PMU driver.
... version: 3
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 3
... event mask: 000000070000000f
rcu: Hierarchical SRCU implementation.
NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
smp: Bringing up secondary CPUs ...
x86: Booting SMP configuration:
.... node #0, CPUs: #1
MDS CPU bug present and SMT on, data leak possible. See for more details.
#2 #3 #4 #5 #6 #7
smp: Brought up 1 node, 8 CPUs
smpboot: Max logical packages: 1
smpboot: Total of 8 processors activated (38311.00 BogoMIPS)
devtmpfs: initialized
x86/mm: Memory block size: 128MB
PM: Registering ACPI NVS region [mem 0x2de7f000-0x2df7efff] (1048576 bytes)
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
pinctrl core: initialized pinctrl subsystem
PM: RTC time: 23:43:46, date: 2020-11-30
NET: Registered protocol family 16
audit: initializing netlink subsys (disabled)
audit: type=2000 audit(1606779826.052:1): state=initialized audit_enabled=0 res=1
EISA bus registered
cpuidle: using governor ladder
cpuidle: using governor menu
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type PCI registered
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: Added _OSI(Linux-Dell-Video)
ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
ACPI: 8 ACPI AML tables successfully acquired and loaded
ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF916E8B7FAC00 0003F3 (v01 PmRef Cpu0Cst 00003001 INTL 20110112)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF916E8B7A3800 0005DB (v01 PmRef ApIst 00003000 INTL 20110112)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF916E8AC9F800 000119 (v01 PmRef ApCst 00003000 INTL 20110112)
ACPI: EC: EC started
ACPI: EC: interrupt blocked
ACPI: \_SB_.PCI0.LPCB.EC0_: Used as first EC
ACPI: \_SB_.PCI0.LPCB.EC0_: GPE=0x16, EC_CMD/EC_SC=0x66, EC_DATA=0x62
ACPI: \_SB_.PCI0.LPCB.EC0_: Boot DSDT EC used to handle transactions
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: Enabled 9 GPEs in block 00 to 3F
ACPI: Power Resource [APPR] (off)
ACPI: Power Resource [COMP] (on)
ACPI: Power Resource [LPP] (on)
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug SHPCHotplug PME LTR]
acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
pci_bus 0000:00: root bus resource [mem 0x4f200000-0xdfffffff window]
pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfedfffff window]
pci_bus 0000:00: root bus resource [mem 0xfee01000-0xffffffff window]
pci_bus 0000:00: root bus resource [bus 00-fe]
pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: [8086:0416] type 00 class 0x030000
pci 0000:00:02.0: reg 0x10: [mem 0xc8400000-0xc87fffff 64bit]
pci 0000:00:02.0: reg 0x18: [mem 0xa0000000-0xafffffff 64bit pref]
pci 0000:00:02.0: reg 0x20: [io 0x4000-0x403f]
pci 0000:00:02.0: BAR 2: assigned to efifb
pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
pci 0000:00:14.0: reg 0x10: [mem 0xc8a20000-0xc8a2ffff 64bit]
pci 0000:00:14.0: PME# supported from D3hot D3cold
pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
pci 0000:00:16.0: reg 0x10: [mem 0xc8a35000-0xc8a3500f 64bit]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: [8086:153a] type 00 class 0x020000
pci 0000:00:19.0: reg 0x10: [mem 0xc8a00000-0xc8a1ffff]
pci 0000:00:19.0: reg 0x14: [mem 0xc8a3b000-0xc8a3bfff]
pci 0000:00:19.0: reg 0x18: [io 0x4080-0x409f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
pci 0000:00:1a.0: reg 0x10: [mem 0xc8a3a000-0xc8a3a3ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
pci 0000:00:1b.0: reg 0x10: [mem 0xc8a30000-0xc8a33fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.6: [8086:8c1c] type 01 class 0x060400
pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.7: [8086:8c1e] type 01 class 0x060400
pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
pci 0000:00:1d.0: reg 0x10: [mem 0xc8a39000-0xc8a393ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.0: [8086:8c4f] type 00 class 0x060100
pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
pci 0000:00:1f.2: reg 0x10: [io 0x40a8-0x40af]
pci 0000:00:1f.2: reg 0x14: [io 0x40b4-0x40b7]
pci 0000:00:1f.2: reg 0x18: [io 0x40a0-0x40a7]
pci 0000:00:1f.2: reg 0x1c: [io 0x40b0-0x40b3]
pci 0000:00:1f.2: reg 0x20: [io 0x4060-0x407f]
pci 0000:00:1f.2: reg 0x24: [mem 0xc8a38000-0xc8a387ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
pci 0000:00:1f.3: reg 0x10: [mem 0xc8a34000-0xc8a340ff 64bit]
pci 0000:00:1f.3: reg 0x20: [io 0xef80-0xef9f]
pci 0000:01:00.0: [10de:13b1] type 00 class 0x030000
pci 0000:01:00.0: reg 0x10: [mem 0xc7000000-0xc7ffffff]
pci 0000:01:00.0: reg 0x14: [mem 0x50000000-0x5fffffff 64bit pref]
pci 0000:01:00.0: reg 0x1c: [mem 0x60000000-0x61ffffff 64bit pref]
pci 0000:01:00.0: reg 0x24: [io 0x3000-0x307f]
pci 0000:01:00.0: reg 0x30: [mem 0xfff80000-0xffffffff pref]
pci 0000:01:00.0: Enabling HDA controller
pci 0000:01:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:01.0 (capable of 126.016 Gb/s with 8 GT/s x16 link)
pci 0000:01:00.1: [10de:0fbc] type 00 class 0x040300
pci 0000:01:00.1: reg 0x10: [mem 0xc8000000-0xc8003fff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:01.0: bridge window [mem 0xc7000000-0xc80fffff]
pci 0000:00:01.0: bridge window [mem 0x50000000-0x61ffffff 64bit pref]
acpiphp: Slot [1] registered
pci 0000:00:1c.0: PCI bridge to [bus 02-3a]
pci 0000:00:1c.0: bridge window [mem 0xb0000000-0xc60fffff]
pci 0000:00:1c.0: bridge window [mem 0x70000000-0x91ffffff 64bit pref]
pci 0000:3b:00.0: [8086:08b1] type 00 class 0x028000
pci 0000:3b:00.0: reg 0x10: [mem 0xc8900000-0xc8901fff 64bit]
pci 0000:3b:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.6: PCI bridge to [bus 3b]
pci 0000:00:1c.6: bridge window [mem 0xc8900000-0xc89fffff]
pci 0000:3c:00.0: [10ec:5249] type 00 class 0xff0000
pci 0000:3c:00.0: reg 0x10: [mem 0xc8800000-0xc8800fff]
pci 0000:3c:00.0: supports D1 D2
pci 0000:3c:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:00:1c.7: PCI bridge to [bus 3c]
pci 0000:00:1c.7: bridge window [mem 0xc8800000-0xc88fffff]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: EC: interrupt unblocked
ACPI: EC: event unblocked
ACPI: \_SB_.PCI0.LPCB.EC0_: GPE=0x16, EC_CMD/EC_SC=0x66, EC_DATA=0x62
ACPI: \_SB_.PCI0.LPCB.EC0_: Boot DSDT EC used to handle transactions and events
iommu: Default domain type: Translated
SCSI subsystem initialized
libata version 3.00 loaded.
pci 0000:00:02.0: vgaarb: setting as boot VGA device
pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
pci 0000:00:02.0: vgaarb: no bridge control possible
pci 0000:01:00.0: vgaarb: bridge control possible
vgaarb: loaded
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
EDAC MC: Ver: 3.0.0
Registered efivars operations
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
e820: reserve RAM buffer [mem 0x00098000-0x0009ffff]
e820: reserve RAM buffer [mem 0x21337018-0x23ffffff]
e820: reserve RAM buffer [mem 0x21348018-0x23ffffff]
e820: reserve RAM buffer [mem 0x2cb7f000-0x2fffffff]
e820: reserve RAM buffer [mem 0x2e000000-0x2fffffff]
e820: reserve RAM buffer [mem 0x8aee00000-0x8afffffff]
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 comparators, 64-bit 14.318180 MHz counter
clocksource: Switched to clocksource tsc-early
*** VALIDATE bpf ***
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
*** VALIDATE ramfs ***
*** VALIDATE hugetlbfs ***
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:00: [mem 0xfed10000-0xfed17fff] has been reserved
system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:00: [mem 0xe0000000-0xefffffff] could not be reserved
system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:00: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:00: [mem 0xfed45000-0xfed8ffff] has been reserved
system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:00: [mem 0x4f210000-0x4f21ffff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:01: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
system 00:02: [io 0x0200-0x027f] has been reserved
system 00:02: [io 0xffff] has been reserved
system 00:02: [io 0xffff] has been reserved
system 00:02: [io 0xffff] has been reserved
system 00:02: [io 0x1800-0x18fe] has been reserved
system 00:02: [io 0xef80-0xef9f] has been reserved
system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:03: [io 0x0800-0x087f] has been reserved
system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:05: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
pnp 00:06: [dma 0 disabled]
pnp 00:06: Plug and Play ACPI device, IDs PNP0401 (active)
pnp 00:07: Plug and Play ACPI device, IDs HPQ8001 PNP0303 (active)
pnp 00:08: Plug and Play ACPI device, IDs SYN300a SYN0100 SYN0002 PNP0f13 (active)
system 00:09: [mem 0x20000000-0x201fffff] could not be reserved
system 00:09: [mem 0x40004000-0x40004fff] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 10 devices
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'bang_bang'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
thermal_sys: Registered thermal governor 'power_allocator'
clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
pci 0000:01:00.0: can't claim BAR 6 [mem 0xfff80000-0xffffffff pref]: no compatible bridge window
pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 02-3a] add_size 1000
pci 0000:00:1c.7: bridge window [io 0x1000-0x0fff] to [bus 3c] add_size 1000
pci 0000:00:1c.7: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 3c] add_size 200000 add_align 100000
pci 0000:00:1c.7: BAR 15: assigned [mem 0x4f300000-0x4f4fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
pci 0000:00:1c.7: BAR 13: assigned [io 0x5000-0x5fff]
pci 0000:01:00.0: BAR 6: assigned [mem 0xc8080000-0xc80fffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:01.0: bridge window [mem 0xc7000000-0xc80fffff]
pci 0000:00:01.0: bridge window [mem 0x50000000-0x61ffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 02-3a]
pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:1c.0: bridge window [mem 0xb0000000-0xc60fffff]
pci 0000:00:1c.0: bridge window [mem 0x70000000-0x91ffffff 64bit pref]
pci 0000:00:1c.6: PCI bridge to [bus 3b]
pci 0000:00:1c.6: bridge window [mem 0xc8900000-0xc89fffff]
pci 0000:00:1c.7: PCI bridge to [bus 3c]
pci 0000:00:1c.7: bridge window [io 0x5000-0x5fff]
pci 0000:00:1c.7: bridge window [mem 0xc8800000-0xc88fffff]
pci 0000:00:1c.7: bridge window [mem 0x4f300000-0x4f4fffff 64bit pref]
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
pci_bus 0000:00: resource 7 [mem 0x4f200000-0xdfffffff window]
pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfedfffff window]
pci_bus 0000:00: resource 9 [mem 0xfee01000-0xffffffff window]
pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:01: resource 1 [mem 0xc7000000-0xc80fffff]
pci_bus 0000:01: resource 2 [mem 0x50000000-0x61ffffff 64bit pref]
pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:02: resource 1 [mem 0xb0000000-0xc60fffff]
pci_bus 0000:02: resource 2 [mem 0x70000000-0x91ffffff 64bit pref]
pci_bus 0000:3b: resource 1 [mem 0xc8900000-0xc89fffff]
pci_bus 0000:3c: resource 0 [io 0x5000-0x5fff]
pci_bus 0000:3c: resource 1 [mem 0xc8800000-0xc88fffff]
pci_bus 0000:3c: resource 2 [mem 0x4f300000-0x4f4fffff 64bit pref]
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 16384 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
TCP: Hash tables configured (established 262144 bind 65536)
UDP hash table entries: 16384 (order: 7, 524288 bytes, linear)
UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes, linear)
NET: Registered protocol family 1
NET: Registered protocol family 44
pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
pci 0000:00:14.0: enabling device (0000 -> 0002)
pci 0000:01:00.1: D0 power state depends on 0000:01:00.0
PCI: CLS 64 bytes, default 64
Trying to unpack rootfs image as initramfs...
Initramfs unpacking failed: Decoding failed
Freeing initrd memory: 96596K
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0x1cb80000-0x20b80000] (64MB)
check: Scanning for low memory corruption every 60 seconds
Initialise system trusted keyrings
Key type blacklist registered
workingset: timestamp_bits=36 max_order=23 bucket_order=0
zbud: loaded
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse: init (API version 7.31)
*** VALIDATE fuse ***
*** VALIDATE fuse ***
Platform Keyring initialized
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
io scheduler mq-deadline registered
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
efifb: probing for efifb
efifb: No BGRT, not showing boot graphics
efifb: framebuffer at 0xa0000000, using 3072k, total 3072k
efifb: mode is 1024x768x32, linelength=4096, pages=1
efifb: scrolling: redraw
efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
fbcon: Deferring console take-over
fb0: EFI VGA frame buffer device
intel_idle: MWAIT substates: 0x42120
intel_idle: v0.4.1 model 0x3C
intel_idle: lapic_timer_reliable_states 0xffffffff
ACPI: AC Adapter [AC] (on-line)
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
ACPI: Sleep Button [SLPB]
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [CPUZ] (63 C)
ACPI BIOS Error (bug): Could not resolve symbol [\_TZ.PSL.CFGD], AE_NOT_FOUND (20190816/psargs-330)
No Local Variables are initialized for Method [PSL_]
No Arguments are initialized for method [PSL_]
ACPI Error: Aborting method \_TZ.PSL due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
ACPI Error: Aborting method \_TZ.GFXZ._PSL due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
ACPI: Invalid passive threshold
thermal LNXTHERM:01: registered as thermal_zone1
ACPI: Thermal Zone [GFXZ] (60 C)
thermal LNXTHERM:02: registered as thermal_zone2
ACPI: Thermal Zone [EXTZ] (0 C)
thermal LNXTHERM:03: registered as thermal_zone3
ACPI: Thermal Zone [LOCZ] (0 C)
ACPI BIOS Error (bug): Could not resolve symbol [\_TZ.PSL.CFGD], AE_NOT_FOUND (20190816/psargs-330)
No Local Variables are initialized for Method [PSL_]
No Arguments are initialized for method [PSL_]
ACPI Error: Aborting method \_TZ.PSL due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
ACPI Error: Aborting method \_TZ.BATZ._PSL due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
ACPI: Invalid passive threshold
thermal LNXTHERM:04: registered as thermal_zone4
ACPI: Thermal Zone [BATZ] (34 C)
thermal LNXTHERM:05: registered as thermal_zone5
ACPI: Thermal Zone [PCHZ] (59 C)
00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
battery: ACPI: Battery Slot [BAT0] (battery present)
battery: ACPI: Battery Slot [BAT1] (battery absent)
Linux agpgart interface v0.103
tpm_tis 00:01: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: TPM is disabled/deactivated (0x7)
loop: module loaded
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
PPP generic driver version 2.4.2
VFIO - User Level meta-driver version: 0.3
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:1a.0: EHCI Host Controller
ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:1a.0: debug port 2
ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
ehci-pci 0000:00:1a.0: irq 16, io mem 0xc8a3a000
ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 5.4.0-53-generic ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ehci-pci 0000:00:1d.0: EHCI Host Controller
ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci-pci 0000:00:1d.0: debug port 2
ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
ehci-pci 0000:00:1d.0: irq 17, io mem 0xc8a39000
ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 5.4.0-53-generic ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-platform: OHCI generic platform driver
uhci_hcd: USB Universal Host Controller Interface driver
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 5.4.0-53-generic xhci-hcd
usb usb3: SerialNumber: 0000:00:14.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 15 ports detected
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 5.4.0-53-generic xhci-hcd
usb usb4: SerialNumber: 0000:00:14.0
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb: port power management may be unreliable
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042: Detected active multiplexing controller, rev 1.1
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: registered as rtc0
rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
i2c /dev entries driver
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
platform eisa.0: Probing EISA bus 0
platform eisa.0: EISA: Cannot allocate resource for mainboard
platform eisa.0: Cannot allocate resource for EISA slot 1
platform eisa.0: Cannot allocate resource for EISA slot 2
platform eisa.0: Cannot allocate resource for EISA slot 3
platform eisa.0: Cannot allocate resource for EISA slot 4
platform eisa.0: Cannot allocate resource for EISA slot 5
platform eisa.0: Cannot allocate resource for EISA slot 6
platform eisa.0: Cannot allocate resource for EISA slot 7
platform eisa.0: Cannot allocate resource for EISA slot 8
platform eisa.0: EISA: Detected 0 cards
intel_pstate: Intel P-state driver initializing
ledtrig-cpu: registered to indicate activity on CPUs
EFI Variables Facility v0.08 2004-May-17
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
usb 1-1: new high-speed USB device number 2 using ehci-pci
drop_monitor: Initializing network drop monitor service
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
Key type dns_resolver registered
RAS: Correctable Errors collector initialized.
microcode: sig=0x306c3, pf=0x10, revision=0x28
microcode: Microcode Update Driver: v2.2.
IPI shorthand broadcast: enabled
sched_clock: Marking stable (3102141899, 380696)->(3113606352, -11083757)
registered taskstats version 1
Loading compiled-in X.509 certificates
Loaded X.509 cert 'Build time autogenerated kernel key: eb955faf7c22797fadc5b822779862097cf478a9'
zswap: loaded using pool lzo/zbud
Key type ._fscrypt registered
Key type .fscrypt registered
usb 2-1: new high-speed USB device number 2 using ehci-pci
usb 3-1: new high-speed USB device number 2 using xhci_hcd
Key type big_key registered
Key type trusted registered
Key type encrypted registered
AppArmor: AppArmor sha1 policy hashing enabled
integrity: Loading X.509 certificate: UEFI:MokListRT
integrity: Loaded X.509 cert 'SomeOrg: shim: a01ee84e9b37ace407961cc468c5909447878469'
integrity: Loading X.509 certificate: UEFI:MokListRT
integrity: Loaded X.509 cert 'Canonical Ltd. Master Certificate Authority: ad91990bc22ab1f517048c23b6655a268e345a63'
ima: Allocated hash algorithm: sha1
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: Error Communicating to TPM chip
ima: No architecture policies found
evm: Initialising EVM extended attributes:
evm: security.selinux
evm: security.SMACK64
evm: security.SMACK64EXEC
evm: security.SMACK64TRANSMUTE
evm: security.SMACK64MMAP
evm: security.apparmor
evm: security.ima
evm: security.capability
evm: HMAC attrs: 0x1
PM: Magic number: 12:412:758
tty ttyS9: hash matches
rtc_cmos 00:04: setting system clock to 2020-11-30T23:43:49 UTC (1606779829)
Freeing unused decrypted memory: 2040K
Freeing unused kernel image memory: 2716K
Write protecting the kernel read-only data: 22528k
Freeing unused kernel image memory: 2008K
Freeing unused kernel image memory: 1188K
x86/mm: Checked W+X mappings: passed, no W+X pages found.
x86/mm: Checking user space page tables
x86/mm: Checked W+X mappings: passed, no W+X pages found.
Run /init as init process
usb 1-1: New USB device found, idVendor=8087, idProduct=8008, bcdDevice= 0.04
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 3-1: New USB device found, idVendor=0424, idProduct=5434, bcdDevice=30.82
usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
acpi PNP0C14:01: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
usb 2-1: New USB device found, idVendor=8087, idProduct=8000, bcdDevice= 0.04
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
ACPI Warning: SystemIO range 0x0000000000001828-0x000000000000182F conflicts with OpRegion 0x0000000000001800-0x000000000000187F (\PMIO) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: SystemIO range 0x0000000000000840-0x000000000000084F conflicts with OpRegion 0x0000000000000800-0x000000000000085F (\_SB.PCI0.PEGP.DGFX.GPIO) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000840-0x000000000000084F conflicts with OpRegion 0x0000000000000800-0x0000000000000BFF (\GPIO) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: SystemIO range 0x0000000000000830-0x000000000000083F conflicts with OpRegion 0x0000000000000800-0x000000000000085F (\_SB.PCI0.PEGP.DGFX.GPIO) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000830-0x000000000000083F conflicts with OpRegion 0x0000000000000800-0x000000000000083F (\GPRL) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000830-0x000000000000083F conflicts with OpRegion 0x0000000000000800-0x0000000000000BFF (\GPIO) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: SystemIO range 0x0000000000000800-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000085F (\_SB.PCI0.PEGP.DGFX.GPIO) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000800-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000083F (\GPRL) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000800-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x0000000000000BFF (\GPIO) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000800-0x000000000000082F conflicts with OpRegion 0x0000000000000810-0x0000000000000813 (\IO_D) (20190816/utaddress-204)
ACPI Warning: SystemIO range 0x0000000000000800-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000080F (\IO_T) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting gpio_ich
rtsx_pci 0000:3c:00.0: enabling device (0000 -> 0002)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
i801_smbus 0000:00:1f.3: SPD Write Disable is set
i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x2f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst
cryptd: max_cpu_qlen set to 1000
AVX2 version of gcm_enc/dec engaged.
AES CTR mode by8 optimization enabled
scsi host0: ahci
scsi host1: ahci
scsi host2: ahci
scsi host3: ahci
scsi host4: ahci
scsi host5: ahci
ata1: SATA max UDMA/133 abar m2048@0xc8a38000 port 0xc8a38100 irq 31
ata2: SATA max UDMA/133 abar m2048@0xc8a38000 port 0xc8a38180 irq 31
ata3: SATA max UDMA/133 abar m2048@0xc8a38000 port 0xc8a38200 irq 31
ata4: SATA max UDMA/133 abar m2048@0xc8a38000 port 0xc8a38280 irq 31
ata5: DUMMY
ata6: SATA max UDMA/133 abar m2048@0xc8a38000 port 0xc8a38380 irq 31
e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
nvidia: loading out-of-tree module taints kernel.
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
usb 4-1: New USB device found, idVendor=0424, idProduct=5434, bcdDevice=30.82
usb 4-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
usb 4-1: Product: USB5534
usb 4-1: Manufacturer: SMSC
usb 4-1: SerialNumber: 1239567
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 4 ports detected
e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) a0:48:1c:d4:d7:df
e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
e1000e 0000:00:19.0 enp0s25: renamed from eth0
checking generic (a0000000 300000) vs hw (a0000000 10000000)
fb0: switching to inteldrmfb from EFI VGA
i915 0000:00:02.0: vgaarb: deactivate vga console
[drm:i915_gem_init_stolen [i915]] *ERROR* conflict detected with stolen region: [mem 0x2f200000-0x4f1fffff]
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
nvidia-nvlink: Nvlink Core is being initialized, major device number 240
nvidia 0000:01:00.0: enabling device (0000 -> 0003)
nvidia 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none
i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] Panel advertises DPCD backlight support, but VBT disagrees. If your backlight controls don't work try booting with i915.enable_dpcd_backlight=1. If your machine needs this, please file a _new_ bug report on bugs.freedesktop.org against DRI -> DRM/Intel
usb 3-2: new full-speed USB device number 3 using xhci_hcd
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 450.80.02 Wed Sep 23 01:13:39 UTC 2020
[drm] Initialized i915 1.6.0 20190822 for 0000:00:02.0 on minor 0
ACPI: Video Device [DGFX] (multi-head: yes rom: yes post: no)
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input10
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input11
fbcon: i915drmfb (fb0) is primary device
fbcon: Deferring console take-over
i915 0000:00:02.0: fb0: i915drmfb frame buffer device
tsc: Refined TSC clocksource calibration: 2394.453 MHz
clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2283bf4e6f2, max_idle_ns: 440795216136 ns
clocksource: Switched to clocksource tsc
ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata1.00: supports DRM functions and may not be fully accessible
ata1.00: ATA-11: Samsung SSD 860 EVO 500GB, RVT04B6Q, max UDMA/133
ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 32), AA
ata1.00: supports DRM functions and may not be fully accessible
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA Samsung SSD 860 4B6Q PQ: 0 ANSI: 5
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb 3-2: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=12.10
usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-2: Product: USB Receiver
usb 3-2: Manufacturer: Logitech
ata1.00: Enabling discard_zeroes_data
sda: sda1 sda2 sda3
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] supports TCG Opal
sd 0:0:0:0: [sda] Attached SCSI disk
usb 3-1.1: new full-speed USB device number 4 using xhci_hcd
usb 3-1.1: config 1 has an invalid interface number: 3 but max is 2
usb 3-1.1: config 1 has an invalid interface number: 3 but max is 2
usb 3-1.1: config 1 has an invalid interface number: 3 but max is 2
usb 3-1.1: config 1 has no interface number 2
usb 3-1.1: New USB device found, idVendor=262a, idProduct=9023, bcdDevice= 0.01
usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1.1: Product: DAC Audio
usb 3-1.1: Manufacturer: E+ Corp.
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: supports DRM functions and may not be fully accessible
ata2.00: NCQ Send/Recv Log not supported
ata2.00: ATA-9: SAMSUNG MZ7PD256HCGM-000H7, DXM06H6Q, max UDMA/133
ata2.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 32), AA
ata2.00: supports DRM functions and may not be fully accessible
ata2.00: NCQ Send/Recv Log not supported
ata2.00: configured for UDMA/133
usb 3-5: new full-speed USB device number 5 using xhci_hcd
scsi 1:0:0:0: Direct-Access ATA SAMSUNG MZ7PD256 6H6Q PQ: 0 ANSI: 5
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] 500118192 512-byte logical blocks: (256 GB/238 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2
sd 1:0:0:0: [sdb] supports TCG Opal
sd 1:0:0:0: [sdb] Attached SCSI disk
usb 3-5: New USB device found, idVendor=138a, idProduct=003f, bcdDevice= 1.04
usb 3-5: New USB device strings: Mfr=0, Product=0, SerialNumber=1
usb 3-5: SerialNumber: 00b0ea874a91
mmc0: cannot verify signal voltage switch
input: PS/2 Generic Mouse as /devices/platform/i8042/serio2/input/input9
usb 3-1.3: new full-speed USB device number 6 using xhci_hcd
mmc0: new ultra high speed SDR104 SDXC card at address 59b4
mmcblk0: mmc0:59b4 ED2S5 119 GiB
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
mmcblk0: p1
usb 3-1.3: New USB device found, idVendor=28bd, idProduct=0094, bcdDevice= 0.00
usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1.3: Product: STAR G640
usb 3-1.3: Manufacturer: XP-PEN
ata3.00: ATA-8: ST500LT012-1DG142, 0002LVM1, max UDMA/133
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32)
usb 3-7: new high-speed USB device number 7 using xhci_hcd
usb 3-7: New USB device found, idVendor=04f2, idProduct=b3ed, bcdDevice=66.61
usb 3-7: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 3-7: Product: HP HD Webcam
usb 3-7: Manufacturer: Chicony Electronics Co.,Ltd.
usb 3-7: SerialNumber: 200901010001
usb 3-1.4: new low-speed USB device number 8 using xhci_hcd
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST500LT012-1DG14 LVM1 PQ: 0 ANSI: 5
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/466 GiB)
sd 2:0:0:0: [sdc] 4096-byte physical blocks
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI removable disk
usb 3-1.4: New USB device found, idVendor=046d, idProduct=c521, bcdDevice=57.01
usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1.4: Product: USB Receiver
usb 3-1.4: Manufacturer: Logitech
usb 3-8: new high-speed USB device number 9 using xhci_hcd
psmouse serio3: synaptics: queried max coordinates: x [..5660], y [..4730]
psmouse serio3: synaptics: queried min coordinates: x [1324..], y [1248..]
psmouse serio3: synaptics: Your touchpad (PNP: SYN300a SYN0100 SYN0002 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
ata4: SATA link down (SStatus 0 SControl 300)
usb 3-8: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
usb 3-8: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 3-8:1.0: USB hub found
hub 3-8:1.0: 2 ports detected
psmouse serio3: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd40123/0x840300/0x26800/0x0, board id: 2706, fw id: 1486004
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio3/input/input12
usb 3-12: new full-speed USB device number 10 using xhci_hcd
ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
usb 3-12: New USB device found, idVendor=8087, idProduct=07dc, bcdDevice= 0.01
usb 3-12: New USB device strings: Mfr=0, Product=0, SerialNumber=0
ata6.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
ata6.00: NCQ Send/Recv Log not supported
ata6.00: ATA-9: SAMSUNG MZMPD256HAGM-000H1, DXM41H0Q, max UDMA/133
ata6.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata6.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
ata6.00: NCQ Send/Recv Log not supported
ata6.00: configured for UDMA/133
hidraw: raw HID events driver (C) Jiri Kosina
scsi 5:0:0:0: Direct-Access ATA SAMSUNG MZMPD256 1H0Q PQ: 0 ANSI: 5
sd 5:0:0:0: Attached scsi generic sg3 type 0
sd 5:0:0:0: [sdd] 500118192 512-byte logical blocks: (256 GB/238 GiB)
sd 5:0:0:0: [sdd] Write Protect is off
sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd3 sdd4 sdd5
sd 5:0:0:0: [sdd] Attached SCSI disk
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.0/0003:046D:C52B.0001/input/input14
hid-generic 0003:046D:C52B.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:14.0-2/input0
input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:046D:C52B.0002/input/input15
input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:046D:C52B.0002/input/input16
input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:046D:C52B.0002/input/input17
hid-generic 0003:046D:C52B.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-2/input1
hid-generic 0003:046D:C52B.0003: hiddev1,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
hid-generic 0003:262A:9023.0004: No inputs registered, leaving
hid-generic 0003:262A:9023.0004: hidraw3: USB HID v1.00 Device [E+ Corp. DAC Audio] on usb-0000:00:14.0-1.1/input0
input: XP-PEN STAR G640 Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.0/0003:28BD:0094.0005/input/input20
hid-generic 0003:28BD:0094.0005: input,hidraw4: USB HID v1.00 Mouse [XP-PEN STAR G640] on usb-0000:00:14.0-1.3/input0
input: XP-PEN STAR G640 as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:28BD:0094.0006/input/input21
input: XP-PEN STAR G640 as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:28BD:0094.0006/input/input22
input: XP-PEN STAR G640 Keyboard as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:28BD:0094.0006/input/input23
hid-generic 0003:28BD:0094.0006: input,hiddev2,hidraw5: USB HID v1.00 Keyboard [XP-PEN STAR G640] on usb-0000:00:14.0-1.3/input1
hid-generic 0003:28BD:0094.0007: hiddev3,hidraw6: USB HID v1.00 Device [XP-PEN STAR G640] on usb-0000:00:14.0-1.3/input2
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:046D:C521.0008/input/input24
hid-generic 0003:046D:C521.0008: input,hidraw7: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-1.4/input0
input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:046D:C521.0009/input/input25
hid-generic 0003:046D:C521.0009: input,hiddev4,hidraw8: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-1.4/input1
logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
input: Logitech Unifying Device. Wireless PID:2008 Keyboard as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.2/0003:046D:C52B.0003/0003:046D:2008.000A/input/input28
input: Logitech Unifying Device. Wireless PID:2008 Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.2/0003:046D:C52B.0003/0003:046D:2008.000A/input/input29
input: Logitech Unifying Device. Wireless PID:2008 System Control as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.2/0003:046D:C52B.0003/0003:046D:2008.000A/input/input30
hid-generic 0003:046D:2008.000A: input,hidraw1: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2008] on usb-0000:00:14.0-2/input2:1
input: Logitech Unifying Device. Wireless PID:101b Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.2/0003:046D:C52B.0003/0003:046D:101B.000B/input/input35
hid-generic 0003:046D:101B.000B: input,hidraw2: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:101b] on usb-0000:00:14.0-2/input2:3
input: Logitech MK700 as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.2/0003:046D:C52B.0003/0003:046D:2008.000A/input/input39
logitech-hidpp-device 0003:046D:2008.000A: input,hidraw1: USB HID v1.11 Keyboard [Logitech MK700] on usb-0000:00:14.0-2/input2:1
input: Logitech M705 as /devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.2/0003:046D:C52B.0003/0003:046D:101B.000B/input/input40
logitech-hidpp-device 0003:046D:101B.000B: input,hidraw2: USB HID v1.11 Mouse [Logitech M705] on usb-0000:00:14.0-2/input2:3
logitech-hidpp-device 0003:046D:2008.000A: HID++ 1.0 device connected.
EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
systemd[1]: Inserted module 'autofs4'
systemd[1]: systemd 245.4-4ubuntu3.3 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
systemd[1]: Detected architecture x86-64.
systemd[1]: Set hostname to .
systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
systemd[1]: Created slice system-modprobe.slice.
systemd[1]: Created slice Cryptsetup Units Slice.
systemd[1]: Created slice system-systemd\x2dfsck.slice.
systemd[1]: Created slice User and Session Slice.
systemd[1]: Started Forward Password Requests to Wall Directory Watch.
systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
systemd[1]: Reached target User and Group Name Lookups.
systemd[1]: Reached target Remote File Systems.
systemd[1]: Reached target Slices.
systemd[1]: Listening on Device-mapper event daemon FIFOs.
systemd[1]: Listening on LVM2 poll daemon socket.
systemd[1]: Listening on Syslog Socket.
systemd[1]: Listening on fsck to fsckd communication Socket.
systemd[1]: Listening on initctl Compatibility Named Pipe.
systemd[1]: Listening on Journal Audit Socket.
systemd[1]: Listening on Journal Socket (/dev/log).
systemd[1]: Listening on Journal Socket.
systemd[1]: Listening on udev Control Socket.
systemd[1]: Listening on udev Kernel Socket.
systemd[1]: Mounting Huge Pages File System...
systemd[1]: Mounting POSIX Message Queue File System...
systemd[1]: Mounting Kernel Debug File System...
systemd[1]: Mounting Kernel Trace File System...
systemd[1]: Starting Journal Service...
systemd[1]: Starting Availability of block devices...
systemd[1]: Starting Set the console keyboard layout...
systemd[1]: Starting Create list of static device nodes for the current kernel...
systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
systemd[1]: Starting Load Kernel Modules...
systemd[1]: Starting Remount Root and Kernel File Systems...
systemd[1]: Starting udev Coldplug all Devices...
systemd[1]: Starting Uncomplicated firewall...
systemd[1]: Mounted Huge Pages File System.
systemd[1]: Mounted POSIX Message Queue File System.
systemd[1]: Mounted Kernel Debug File System.
systemd[1]: Mounted Kernel Trace File System.
systemd[1]: Finished Availability of block devices.
systemd[1]: Finished Create list of static device nodes for the current kernel.
systemd[1]: Finished Uncomplicated firewall.
EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
systemd[1]: Finished Remount Root and Kernel File Systems.
systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
systemd[1]: Starting Load/Save Random Seed...
systemd[1]: Starting Create System Users...
systemd[1]: Finished Set the console keyboard layout.
systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
parport_pc 00:06: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 5, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP]
systemd[1]: Finished Create System Users.
systemd[1]: Starting Create Static Device Nodes in /dev...
systemd[1]: Finished Load/Save Random Seed.
systemd[1]: Finished Create Static Device Nodes in /dev.
systemd[1]: Reached target Local File Systems (Pre).
systemd[1]: Mounting Mount unit for core18, revision 1885...
systemd[1]: Mounting Mount unit for core18, revision 1932...
systemd[1]: Mounting Mount unit for discord, revision 115...
systemd[1]: Mounting Mount unit for gnome-3-28-1804, revision 145...
systemd[1]: Mounting Mount unit for gnome-3-34-1804, revision 36...
systemd[1]: Mounting Mount unit for gnome-3-34-1804, revision 60...
systemd[1]: Mounting Mount unit for gtk-common-themes, revision 1506...
systemd[1]: Mounting Mount unit for kde-frameworks-5-core18, revision 32...
systemd[1]: Mounting Mount unit for snap-store, revision 467...
systemd[1]: Mounting Mount unit for snap-store, revision 481...
systemd[1]: Mounting Mount unit for snapd, revision 9607...
systemd[1]: Mounting Mount unit for snapd, revision 9721...
systemd[1]: Mounting Mount unit for youtube-dl, revision 2925...
systemd[1]: Mounting Mount unit for youtube-dl, revision 2927...
systemd[1]: Starting udev Kernel Device Manager...
lp0: using parport0 (interrupt-driven).
systemd[1]: Finished Load Kernel Modules.
systemd[1]: Mounting FUSE Control File System...
systemd[1]: Mounting Kernel Configuration File System...
systemd[1]: Starting Apply Kernel Variables...
systemd[1]: Started Journal Service.
systemd-journald[558]: Received client request to flush runtime journal.
nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms 450.80.02 Wed Sep 23 00:48:09 UTC 2020
[drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
[drm] Initialized nvidia-drm 0.0.0 20160202 for 0000:01:00.0 on minor 1
nvidia_uvm: module verification failed: signature and/or required key missing - tainting kernel
nvidia-uvm: Loaded the UVM driver, major device number 236.
input: HP Wireless hotkeys as /devices/virtual/input/input41
hp_accel: hardware type HPZBook15 found
EDAC ie31200: No ECC support
EDAC ie31200: No ECC support
cfg80211: Loading compiled-in X.509 certificates for regulatory database
cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
mc: Linux media interface: v0.10
Bluetooth: Core ver 2.22
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
lis3lv02d: 8 bits 3DC sensor found
input: XP-PEN STAR G640 Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.0/0003:28BD:0094.0005/input/input42
input: XP-PEN STAR G640 Mouse as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.0/0003:28BD:0094.0005/input/input43
uclogic 0003:28BD:0094.0005: input,hidraw4: USB HID v1.00 Mouse [XP-PEN STAR G640] on usb-0000:00:14.0-1.3/input0
videodev: Linux video capture interface: v2.00
Intel(R) Wireless WiFi driver for Linux
Copyright(c) 2003- 2015 Intel Corporation
iwlwifi 0000:3b:00.0: enabling device (0000 -> 0002)
iwlwifi 0000:3b:00.0: loaded firmware version 17.3216344376.0 op_mode iwlmvm
uvcvideo: Found UVC 1.00 device HP HD Webcam (04f2:b3ed)
uvcvideo 3-7:1.0: Entity type for entity Extension 5 was not initialized!
uvcvideo 3-7:1.0: Entity type for entity Extension 2 was not initialized!
uvcvideo 3-7:1.0: Entity type for entity Processing 3 was not initialized!
uvcvideo 3-7:1.0: Entity type for entity Camera 1 was not initialized!
input: HP HD Webcam: HP HD Webcam as /devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7:1.0/input/input45
input: HP WMI hotkeys as /devices/virtual/input/input44
iwlwifi 0000:3b:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
RAPL PMU: hw unit of domain package 2^-14 Joules
RAPL PMU: hw unit of domain dram 2^-14 Joules
RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
iwlwifi 0000:3b:00.0: base HW address: 0c:8b:fd:73:d7:0a
usbcore: registered new interface driver btusb
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
input: XP-PEN STAR G640 Pen as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:28BD:0094.0006/input/input46
Bluetooth: hci0: read Intel version: 370710018002030d00
uclogic 0003:28BD:0094.0006: input,hidraw5: USB HID v1.00 Device [XP-PEN STAR G640] on usb-0000:00:14.0-1.3/input1
uclogic 0003:28BD:0094.0007: hiddev1,hidraw6: USB HID v1.00 Device [XP-PEN STAR G640] on usb-0000:00:14.0-1.3/input2
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
usbcore: registered new interface driver snd-usb-audio
snd_hda_intel 0000:01:00.1: enabling device (0000 -> 0002)
snd_hda_intel 0000:01:00.1: Disabling MSI
snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
snd_hda_codec_idt hdaudioC0D0: autoconfig for 92HD91BXX: line_outs=1 (0xa/0x0/0x0/0x0/0x0) type:line
snd_hda_codec_idt hdaudioC0D0: speaker_outs=1 (0xd/0x0/0x0/0x0/0x0)
snd_hda_codec_idt hdaudioC0D0: hp_outs=1 (0xb/0x0/0x0/0x0/0x0)
snd_hda_codec_idt hdaudioC0D0: mono: mono_out=0x0
snd_hda_codec_idt hdaudioC0D0: inputs:
snd_hda_codec_idt hdaudioC0D0: Mic=0xc
snd_hda_codec_idt hdaudioC0D0: Internal Mic=0x11
snd_hda_codec_idt hdaudioC0D0: Line=0xf
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input47
input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input48
input: HDA Intel PCH Dock Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input49
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input50
Bluetooth: hci0: unexpected event for opcode 0xfc2f
Bluetooth: hci0: Intel firmware patch completed and activated
ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
intel_rapl_common: Found RAPL domain package
intel_rapl_common: Found RAPL domain core
intel_rapl_common: Found RAPL domain uncore
intel_rapl_common: Found RAPL domain dram
Adding 1003516k swap on /dev/mapper/vgubuntu-swap_1. Priority:-2 extents:1 across:1003516k SSFS
iwlwifi 0000:3b:00.0 wlo1: renamed from wlan0
EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
audit: type=1400 audit(1606779848.031:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=1119 comm="apparmor_parser"
audit: type=1400 audit(1606779848.031:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=1115 comm="apparmor_parser"
audit: type=1400 audit(1606779848.031:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ippusbxd" pid=1116 comm="apparmor_parser"
audit: type=1400 audit(1606779848.031:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=1110 comm="apparmor_parser"
audit: type=1400 audit(1606779848.031:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=1110 comm="apparmor_parser"
audit: type=1400 audit(1606779848.031:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=1111 comm="apparmor_parser"
audit: type=1400 audit(1606779848.031:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=1111 comm="apparmor_parser"
audit: type=1400 audit(1606779848.035:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=1122 comm="apparmor_parser"
audit: type=1400 audit(1606779848.035:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/tcpdump" pid=1114 comm="apparmor_parser"
audit: type=1400 audit(1606779848.035:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=1124 comm="apparmor_parser"
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
NET: Registered protocol family 38
input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input51
input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input52
input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input53
input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input54
input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input55
input: HDA NVidia HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input56
input: HDA NVidia HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input57
ACPI Warning: \_SB.PCI0.PEGP.DGFX._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20190816/nsarguments-59)
e1000e: enp0s25 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): enp0s25: link becomes ready
rfkill: input handler disabled
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
rfkill: input handler enabled
exfat: module is from the staging directory, the quality is unknown, you have been warned.
exFAT: Version 1.3.0
[EXFAT] trying to mount...
rfkill: input handler disabled
[EXFAT] mounted successfully
kauditd_printk_skb: 29 callbacks suppressed
audit: type=1400 audit(1606779870.767:41): apparmor="DENIED" operation="capable" profile="/usr/lib/snapd/snap-confine" pid=2510 comm="snap-confine" capability=4 capname="fsetid"
audit: type=1400 audit(1606779872.223:42): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/mime.cache" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:43): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/globs2" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:44): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/magic" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:45): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/aliases" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:46): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/subclasses" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:47): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/icons" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:48): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/var/lib/snapd/hostfs/usr/share/mime/generic-icons" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606779872.223:49): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/etc/gnome/defaults.list" pid=2510 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1326 audit(1606779872.259:50): auid=1000 uid=1000 gid=1000 ses=3 pid=2510 comm="snap-store" exe="/snap/snap-store/481/usr/bin/snap-store" sig=0 arch=c000003e syscall=314 compat=0 ip=0x7fad70791959 code=0x50000
logitech-hidpp-device 0003:046D:101B.000B: HID++ 1.0 device connected.
SGI XFS with ACLs, security attributes, realtime, no debug enabled
JFS: nTxBlock = 8192, nTxLock = 65536
ntfs: driver 2.1.32 [Flags: R/O MODULE].
QNX4 filesystem 0.2.3 registered.
raid6: avx2x4 gen() 26833 MB/s
raid6: avx2x4 xor() 17578 MB/s
raid6: avx2x2 gen() 23743 MB/s
raid6: avx2x2 xor() 15085 MB/s
raid6: avx2x1 gen() 20660 MB/s
raid6: avx2x1 xor() 14396 MB/s
raid6: sse2x4 gen() 15372 MB/s
raid6: sse2x4 xor() 9892 MB/s
raid6: sse2x2 gen() 13027 MB/s
raid6: sse2x2 xor() 8656 MB/s
raid6: sse2x1 gen() 11057 MB/s
raid6: sse2x1 xor() 7490 MB/s
raid6: using algorithm avx2x4 gen() 26833 MB/s
raid6: .... xor() 17578 MB/s, rmw enabled
raid6: using avx2x2 recovery algorithm
xor: automatically using best checksumming function avx
Btrfs loaded, crc32c=crc32c-intel
kauditd_printk_skb: 16 callbacks suppressed
audit: type=1326 audit(1606733252.601:67): auid=1000 uid=1000 gid=1000 ses=3 pid=9206 comm="snap-store" exe="/snap/snap-store/498/usr/bin/snap-store" sig=0 arch=c000003e syscall=314 compat=0 ip=0x7f4313c12959 code=0x50000
audit: type=1107 audit(1606733252.729:68): pid=1164 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/NetworkManager" interface="org.freedesktop.DBus.Properties" member="GetAll" mask="send" name=":1.8" pid=9206 label="snap.snap-store.ubuntu-software-local-file" peer_pid=1165 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
audit: type=1107 audit(1606733253.053:69): pid=1164 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.DBus.Properties" member="GetAll" mask="send" name=":1.7" pid=9206 label="snap.snap-store.ubuntu-software-local-file" peer_pid=1189 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
audit: type=1107 audit(1606733253.053:70): pid=1164 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.PolicyKit1.Authority" member="CheckAuthorization" mask="send" name=":1.7" pid=9206 label="snap.snap-store.ubuntu-software-local-file" peer_pid=1189 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
audit: type=1400 audit(1606733255.005:71): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/var/lib/snapd/hostfs/usr/share/gdm/greeter/applications/gnome-initial-setup.desktop" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606733255.037:72): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/var/lib/snapd/hostfs/usr/share/gdm/greeter/applications/gnome-initial-setup.desktop" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1326 audit(1606733255.529:73): auid=1000 uid=1000 gid=1000 ses=3 pid=9206 comm="snap-store" exe="/snap/snap-store/498/usr/bin/snap-store" sig=0 arch=c000003e syscall=93 compat=0 ip=0x7f4313c08527 code=0x50000
audit: type=1107 audit(1606733255.557:74): pid=1164 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.DBus.Properties" member="GetAll" mask="send" name=":1.7" pid=9206 label="snap.snap-store.ubuntu-software-local-file" peer_pid=1189 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
audit: type=1107 audit(1606733255.557:75): pid=1164 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.PolicyKit1.Authority" member="CheckAuthorization" mask="send" name=":1.7" pid=9206 label="snap.snap-store.ubuntu-software-local-file" peer_pid=1189 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
audit: type=1400 audit(1606733255.809:76): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/etc/PackageKit/Vendor.conf" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
perf: interrupt took too long (2509 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
perf: interrupt took too long (3140 > 3136), lowering kernel.perf_event_max_sample_rate to 63500
perf: interrupt took too long (3934 > 3925), lowering kernel.perf_event_max_sample_rate to 50750
perf: interrupt took too long (4921 > 4917), lowering kernel.perf_event_max_sample_rate to 40500
audit: type=1400 audit(1606762118.375:77): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/var/lib/snapd/hostfs/usr/share/gdm/greeter/applications/gnome-initial-setup.desktop" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606762118.407:78): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/var/lib/snapd/hostfs/usr/share/gdm/greeter/applications/gnome-initial-setup.desktop" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1326 audit(1606762118.867:79): auid=1000 uid=1000 gid=1000 ses=3 pid=9206 comm="snap-store" exe="/snap/snap-store/498/usr/bin/snap-store" sig=0 arch=c000003e syscall=93 compat=0 ip=0x7f4313c08527 code=0x50000
audit: type=1400 audit(1606766361.930:80): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="/snap/snapd/9721/usr/lib/snapd/snap-confine" pid=45375 comm="apparmor_parser"
audit: type=1400 audit(1606766361.930:81): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="/snap/snapd/9721/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=45375 comm="apparmor_parser"
audit: type=1400 audit(1606766362.070:82): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.youtube-dl.youtube-dl" pid=45377 comm="apparmor_parser"
audit: type=1400 audit(1606766362.070:83): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="snap-update-ns.youtube-dl" pid=45379 comm="apparmor_parser"
mce: CPU5: Core temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU4: Core temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU2: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU1: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU0: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU3: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU7: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU6: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU4: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU5: Package temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU4: Core temperature/speed normal
mce: CPU3: Package temperature/speed normal
mce: CPU2: Package temperature/speed normal
mce: CPU0: Package temperature/speed normal
mce: CPU1: Package temperature/speed normal
mce: CPU5: Core temperature/speed normal
mce: CPU6: Package temperature/speed normal
mce: CPU7: Package temperature/speed normal
mce: CPU5: Package temperature/speed normal
mce: CPU4: Package temperature/speed normal
mce: CPU7: Core temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU5: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU6: Core temperature above threshold, cpu clock throttled (total events = 1)
mce: CPU4: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU6: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU7: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU1: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU0: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU3: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU2: Package temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU7: Core temperature/speed normal
mce: CPU5: Package temperature/speed normal
mce: CPU6: Core temperature/speed normal
mce: CPU4: Package temperature/speed normal
mce: CPU7: Package temperature/speed normal
mce: CPU6: Package temperature/speed normal
mce: CPU2: Package temperature/speed normal
mce: CPU3: Package temperature/speed normal
mce: CPU0: Package temperature/speed normal
mce: CPU1: Package temperature/speed normal
mce: CPU4: Core temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU5: Core temperature above threshold, cpu clock throttled (total events = 5)
mce: CPU1: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU6: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU2: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU0: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU7: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU3: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU5: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU4: Package temperature above threshold, cpu clock throttled (total events = 15)
mce: CPU5: Core temperature/speed normal
mce: CPU1: Package temperature/speed normal
mce: CPU0: Package temperature/speed normal
mce: CPU7: Package temperature/speed normal
mce: CPU6: Package temperature/speed normal
mce: CPU2: Package temperature/speed normal
mce: CPU3: Package temperature/speed normal
mce: CPU4: Core temperature/speed normal
mce: CPU5: Package temperature/speed normal
mce: CPU4: Package temperature/speed normal
audit: type=1400 audit(1606790918.783:84): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/var/lib/snapd/hostfs/usr/share/gdm/greeter/applications/gnome-initial-setup.desktop" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1400 audit(1606790918.819:85): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software-local-file" name="/var/lib/snapd/hostfs/usr/share/gdm/greeter/applications/gnome-initial-setup.desktop" pid=9206 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
audit: type=1326 audit(1606790919.364:86): auid=1000 uid=1000 gid=1000 ses=3 pid=9206 comm="snap-store" exe="/snap/snap-store/498/usr/bin/snap-store" sig=0 arch=c000003e syscall=93 compat=0 ip=0x7f4313c08527 code=0x50000
audit: type=1400 audit(1606820413.731:87): apparmor="DENIED" operation="capable" profile="/usr/sbin/cups-browsed" pid=78365 comm="cups-browsed" capability=23 capname="sys_nice"