dmesg - db410c
msm_otg 78d9000.phy: no vddcx
msm_hsusb_host 78d9000.ehci: EHCI Host Controller
msm_hsusb_host 78d9000.ehci: new USB bus registered, assigned bus number 1
msm_hsusb_host 78d9000.ehci: irq 149, io mem 0x078d9000
ov5645 1-0078: ov5645_s_power: on = 1
1b0c000.qcom,cci supply qcom,gdscr-vdd not found, using dummy regulator
msm_cci_init:1016: hw_version = 0x10000008
msm_hsusb_host 78d9000.ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 4.4.9-linaro-lt-qcom ehci_hcd
usb usb1: SerialNumber: 78d9000.ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ov5645 1-0078: ov5645_set_power_on: Enter
msm_cci_irq:1279 MASTER_0 error 0x8000000
ov5645 1-0078: ov5645_write_reg: write reg error -22: reg=3103, val=11
ov5645 1-0078: could not set init registers
ov5645 1-0078: ov5645_set_power_off: Enter
ov5645 1-0078: could not power up OV5645
ov5645: probe of 1-0078 failed with error -22
qcom-camss 1b0ac00.camss: notifier->num_subdevs = 1
qcom-camss 1b0ac00.camss: msm_csiphy_subdev_init: Enter
qcom-camss 1b0ac00.camss: msm_csiphy_subdev_init: Exit
qcom-camss 1b0ac00.camss: msm_csiphy_subdev_init: Enter
qcom-camss 1b0ac00.camss: msm_csiphy_subdev_init: Exit
input: gpio_keys as /devices/platform/gpio_keys/input/input1
rtc-pm8xxx 200f000.spmi:pm8916@0:rtc@6000: setting system clock to 1970-01-01 00:36:29 UTC (2189)
ALSA device list:
#0: DB410c
Freeing unused kernel memory: 572K (ffffffc000c1e000 - ffffffc000cad000)
Freeing alternatives memory: 64K (ffffffc000cad000 - ffffffc000cbd000)
random: systemd-udevd urandom read with 12 bits of entropy available
usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
usb 1-1: New USB device found, idVendor=0424, idProduct=2513
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: (null)
usb 1-1.2: new high-speed USB device number 3 using msm_hsusb_host
usb 1-1.2: New USB device found, idVendor=1a40, idProduct=0101
usb 1-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1.2: Product: USB 2.0 Hub
hub 1-1.2:1.0: USB hub found
hub 1-1.2:1.0: 4 ports detected
systemd[1]: System time before build time, advancing clock.
systemd[1]: Failed to insert module 'kdbus': Function not implemented
systemd[1]: systemd 230 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
systemd[1]: Detected architecture arm64.
systemd[1]: Set hostname to .
usb 1-1.2.2: new low-speed USB device number 4 using msm_hsusb_host
usb 1-1.2.2: New USB device found, idVendor=04ca, idProduct=008a
usb 1-1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2.2: Product: USB Optical Mouse
usb 1-1.2.2: Manufacturer: PixArt
input: PixArt USB Optical Mouse as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2.2/1-1.2.2:1.0/0003:04CA:008A.0001/input/input2
hid-generic 0003:04CA:008A.0001: input: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-78d9000.ehci-1.2.2/input0
systemd[1]: Listening on Journal Socket (/dev/log).
systemd[1]: Reached target Encrypted Volumes.
systemd[1]: Listening on udev Control Socket.
usb 1-1.2.3: new low-speed USB device number 5 using msm_hsusb_host
systemd[1]: Reached target Swap.
systemd[1]: Listening on Journal Audit Socket.
systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
systemd[1]: Listening on Syslog Socket.
systemd[1]: Listening on udev Kernel Socket.
usb 1-1.2.3: New USB device found, idVendor=04ca, idProduct=007d
usb 1-1.2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
systemd[1]: Started Forward Password Requests to Wall Directory Watch.
usb 1-1.2.3: Product: USB wired keyboard
usb 1-1.2.3: Manufacturer: Liteon Technology Corp.
input: Liteon Technology Corp. USB wired keyboard as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2.3/1-1.2.3:1.0/0003:04CA:007D.0002/input/input3
systemd[1]: Created slice User and Session Slice.
hid-generic 0003:04CA:007D.0002: input: USB HID v1.11 Keyboard [Liteon Technology Corp. USB wired keyboard] on usb-78d9000.ehci-1.2.3/input0
input: Liteon Technology Corp. USB wired keyboard as /devices/platform/soc/78d9000.ehci/usb1/1-1/1-1.2/1-1.2.3/1-1.2.3:1.1/0003:04CA:007D.0003/input/input4
systemd[1]: Listening on Journal Socket.
systemd[1]: Created slice System Slice.
hid-generic 0003:04CA:007D.0003: input: USB HID v1.11 Device [Liteon Technology Corp. USB wired keyboard] on usb-78d9000.ehci-1.2.3/input1
systemd[1]: Starting Nameserver information manager...
systemd[1]: Reached target Slices.
systemd[1]: Mounting Huge Pages File System...
systemd[1]: Created slice system-getty.slice.
systemd[1]: Starting Load Kernel Modules...
systemd[1]: Mounting POSIX Message Queue File System...
systemd[1]: Created slice system-serial\x2dgetty.slice.
systemd[1]: Mounting Debug File System...
systemd[1]: Starting Create list of required static device nodes for the current kernel...
systemd[1]: Reached target Remote File Systems (Pre).
systemd[1]: Reached target Remote File Systems.
systemd[1]: Starting LSB: Prepare console...
systemd[1]: Starting Journal Service...
systemd[1]: Mounted Debug File System.
systemd[1]: Mounted POSIX Message Queue File System.
systemd[1]: Mounted Huge Pages File System.
systemd[1]: Started Load Kernel Modules.
systemd[1]: Started Create list of required static device nodes for the current kernel.
systemd[1]: Started Nameserver information manager.
systemd[1]: Started Journal Service.
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
alloc_contig_range: [bc078, bc080) PFNs busy
systemd-journald[1430]: Received request to flush runtime journal from PID 1
qcom-camss 1b0ac00.camss: ispif_set_power: Enter, on = 1
remoteproc1: powering up soc:vidc_tzpil@0
qcom-camss 1b0ac00.camss: ispif_set_power: Exit, on = 1
remoteproc1: Booting fw image venus.mdt, size 6812
qcom-camss 1b0ac00.camss: msm_vfe_subdev_set_power: Enter, on = 1
qcom-camss 1b0ac00.camss: VFE HW Version = 0x10030000
qcom-camss 1b0ac00.camss: msm_vfe_subdev_set_power: Exit, on = 1
qcom-camss 1b0ac00.camss: ispif_set_power: Enter, on = 0
qcom-camss 1b0ac00.camss: ispif_set_power: Exit, on = 0
qcom-camss 1b0ac00.camss: msm_vfe_subdev_set_power: Enter, on = 0
qcom-camss 1b0ac00.camss: msm_vfe_subdev_set_power: Exit, on = 0
qcom-tz-pil soc:vidc_tzpil@0: start successful
remoteproc1: remote processor soc:vidc_tzpil@0 is now up
remoteproc2: powering up a204000.wcnss
remoteproc2: Booting fw image wcnss.mdt, size 7260
remoteproc2: remote processor a204000.wcnss is now up
qcom_wcnss_ctrl pronto.wcnss: WCNSS Version 1.5 1.2
1c00000.qcom,adreno-3xx supply vdd not found, using dummy regulator
1c00000.qcom,adreno-3xx supply vddcx not found, using dummy regulator
msm 1a00000.qcom,mdss_mdp: A306: using IOMMU
adreno 1c00000.qcom,adreno-3xx: couldn't get gfx3d1_user context
adreno 1c00000.qcom,adreno-3xx: couldn't get gfx3d1_priv context
alloc_contig_range: [bc0a0, bc0a8) PFNs busy
wcn36xx: mac address: 02:00:09:58:1d:88
random: nonblocking pool is initialized
wcn36xx: firmware WLAN version 'WCN v2.0 RadioPhy vRhea_GF_1.12 with 19.2MHz XO' and CRM version 'CNSS-PR-2-0-1-2-c1-00010'
wcn36xx: firmware API 1.5.1.2, 41 stations, 2 bssids
wcn36xx: FW Cap MCC
wcn36xx: FW Cap P2P
wcn36xx: FW Cap SLM_SESSIONIZATION
wcn36xx: FW Cap DOT11AC_OPMODE
wcn36xx: FW Cap SAP32STA
wcn36xx: FW Cap TDLS
wcn36xx: FW Cap P2P_GO_NOA_DECOUPLE_INIT_SCAN
wcn36xx: FW Cap WLANACTIVE_OFFLOAD
wcn36xx: FW Cap BEACON_OFFLOAD
wcn36xx: FW Cap SCAN_OFFLOAD
wcn36xx: FW Cap BCN_MISS_OFFLOAD
wcn36xx: FW Cap STA_POWERSAVE
wcn36xx: FW Cap STA_ADVANCED_PWRSAVE
wcn36xx: FW Cap BCN_FILTER
wcn36xx: FW Cap RTT
wcn36xx: FW Cap RATECTRL
wcn36xx: FW Cap WOW
wcn36xx: FW Cap WLAN_ROAM_SCAN_OFFLOAD
wcn36xx: FW Cap SPECULATIVE_PS_POLL
wcn36xx: FW Cap IBSS_HEARTBEAT_OFFLOAD
wcn36xx: FW Cap WLAN_SCAN_OFFLOAD
wcn36xx: FW Cap WLAN_PERIODIC_TX_PTRN
wcn36xx: FW Cap ADVANCE_TDLS
wcn36xx: FW Cap BATCH_SCAN
wcn36xx: FW Cap FW_IN_TX_PATH
wcn36xx: FW Cap EXTENDED_NSOFFLOAD_SLOT
wcn36xx: FW Cap CH_SWITCH_V1
wcn36xx: FW Cap HT40_OBSS_SCAN
wcn36xx: FW Cap UPDATE_CHANNEL_LIST
wcn36xx: FW Cap WLAN_MCADDR_FLT
wcn36xx: FW Cap WLAN_CH144
wcn36xx: FW Cap TDLS_SCAN_COEXISTENCE
wcn36xx: FW Cap LINK_LAYER_STATS_MEAS
wcn36xx: FW Cap EXTENDED_SCAN
wcn36xx: FW Cap DYNAMIC_WMM_PS
wcn36xx: FW Cap MAC_SPOOFED_SCAN
wcn36xx: FW Cap FW_STATS
wcn36xx: FW Cap WPS_PRBRSP_TMPL
wcn36xx: FW Cap BCN_IE_FLT_DELTA
wlan0: authenticate with 00:25:45:35:e4:f0
wlan0: send auth to 00:25:45:35:e4:f0 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:25:45:35:e4:f0 (try 1/3)
wlan0: RX AssocResp from 00:25:45:35:e4:f0 (capab=0x431 status=0 aid=1)
wlan0: associated
wlan0: Limiting TX power to 5 dBm as advertised by 00:25:45:35:e4:f0
cfg80211: Regulatory domain changed to country: CA
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
wcn36xx: ERROR hal_remove_bsskey response failed err=6
wlan0: authenticate with 00:25:45:35:e9:d0
wlan0: send auth to 00:25:45:35:e9:d0 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:25:45:35:e9:d0 (try 1/3)
wlan0: RX AssocResp from 00:25:45:35:e9:d0 (capab=0x431 status=0 aid=4)
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
wlan0: associated
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
wlan0: Limiting TX power to 11 dBm as advertised by 00:25:45:35:e9:d0
cfg80211: Regulatory domain changed to country: CA
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
wlan0: deauthenticated from 00:25:45:35:e9:d0 (Reason: 2=PREV_AUTH_NOT_VALID)
wcn36xx: ERROR hal_remove_bsskey response failed err=16
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
wlan0: authenticate with 00:25:45:35:e4:00
wlan0: send auth to 00:25:45:35:e4:00 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:25:45:35:e4:00 (try 1/3)
wlan0: RX AssocResp from 00:25:45:35:e4:00 (capab=0x431 status=0 aid=2)
wlan0: associated
cfg80211: Regulatory domain changed to country: CA
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
wlan0: Limiting TX power to 14 dBm as advertised by 00:25:45:35:e4:00
wcn36xx: ERROR hal_remove_bsskey response failed err=6
wlan0: authenticate with 00:25:45:35:e9:d0
wlan0: send auth to 00:25:45:35:e9:d0 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:25:45:35:e9:d0 (try 1/3)
wlan0: RX AssocResp from 00:25:45:35:e9:d0 (capab=0x431 status=0 aid=4)
wlan0: associated
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
wlan0: Limiting TX power to 11 dBm as advertised by 00:25:45:35:e9:d0
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
cfg80211: Regulatory domain changed to country: CA
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
wlan0: Limiting TX power to 8 dBm as advertised by 00:25:45:35:e9:d0
wlan0: deauthenticated from 00:25:45:35:e9:d0 (Reason: 7=CLASS3_FRAME_FROM_NONASSOC_STA)
wcn36xx: ERROR hal_remove_bsskey response failed err=16
wlan0: authenticate with 00:25:45:35:e9:d0
wlan0: send auth to 00:25:45:35:e9:d0 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:25:45:35:e9:d0 (try 1/3)
wlan0: RX AssocResp from 00:25:45:35:e9:d0 (capab=0x431 status=0 aid=1)
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
wlan0: associated
wlan0: Limiting TX power to 8 dBm as advertised by 00:25:45:35:e9:d0
cfg80211: Regulatory domain changed to country: CA
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
usb 1-1.1: new high-speed USB device number 6 using msm_hsusb_host
usb 1-1.1: New USB device found, idVendor=0951, idProduct=1666
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: DataTraveler 3.0
usb 1-1.1: Manufacturer: Kingston
usb 1-1.1: SerialNumber: 60A44C4138F0BFC0898B011D
usb-storage 1-1.1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 1-1.1:1.0
scsi 0:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6
sd 0:0:0:0: [sda] 15138816 512-byte logical blocks: (7.75 GB/7.22 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
wlan0: deauthenticated from 00:25:45:35:e9:d0 (Reason: 1=UNSPECIFIED)
wcn36xx: ERROR hal_remove_bsskey response failed err=16
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
wlan0: authenticate with 00:25:45:35:e2:40
wlan0: send auth to 00:25:45:35:e2:40 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:25:45:35:e2:40 (try 1/3)
wlan0: RX AssocResp from 00:25:45:35:e2:40 (capab=0x431 status=0 aid=3)
wlan0: associated
wlan0: Limiting TX power to 5 dBm as advertised by 00:25:45:35:e2:40
cfg80211: Regulatory domain changed to country: CA
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s)
cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
wlan0: Limiting TX power to 8 dBm as advertised by 00:25:45:35:e2:40
usb 1-1.2: clear tt 1 (0040) error -71
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2: clear tt 1 (0050) error -71
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2: clear tt 1 (0050) error -71
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: Cannot enable. Maybe the USB cable is bad?
usb 1-1.2-port2: cannot disable (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: Cannot enable. Maybe the USB cable is bad?
usb 1-1.2-port2: cannot disable (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: Cannot enable. Maybe the USB cable is bad?
usb 1-1.2-port2: cannot disable (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: cannot reset (err = -71)
usb 1-1.2-port2: Cannot enable. Maybe the USB cable is bad?
usb 1-1.2-port2: cannot disable (err = -71)
usb 1-1.2-port2: cannot disable (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
hub 1-1.2:1.0: hub_port_status failed (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: Cannot enable. Maybe the USB cable is bad?
usb 1-1.2-port3: cannot disable (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: cannot reset (err = -71)
usb 1-1.2-port3: Cannot enable. Maybe the USB cable is bad?
usb 1-1.2-port3: cannot disable (err = -71)
usb 1-1.2: USB disconnect, device number 3
usb 1-1.2.2: USB disconnect, device number 4
usb 1-1.2.3: USB disconnect, device number 5
usb 1-1.2-port3: cannot reset (err = -71)