dmesg - gmpbench_ocz
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 3.11.0-14-generic (buildd@allspice) (gcc version 4.8.1 (Ubuntu/Linaro 4.8.1-10ubuntu8) ) #21-Ubuntu SMP Tue Nov 12 17:04:55 UTC 2013 (Ubuntu 3.11.0-14.21-generic 3.11.7)
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
e820: BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009cbff] usable
BIOS-e820: [mem 0x000000000009cc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x00000000dff6ffff] usable
BIOS-e820: [mem 0x00000000dff70000-0x00000000dff7dfff] ACPI data
BIOS-e820: [mem 0x00000000dff7e000-0x00000000dffcffff] ACPI NVS
BIOS-e820: [mem 0x00000000dffd0000-0x00000000dfffffff] reserved
BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved
BIOS-e820: [mem 0x0000000100000000-0x000000011fffffff] usable
NX (Execute Disable) protection: active
SMBIOS 2.5 present.
DMI: System manufacturer P5Q3 DELUXE/P5Q3 DELUXE, BIOS 2105 05/26/2009
e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
No AGP bridge found
e820: last_pfn = 0x120000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-DFFFF write-protect
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F00000000 write-back
1 base 100000000 mask FE0000000 write-back
2 base 0E0000000 mask FE0000000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 4GB, type WB
reg 1, base: 4GB, range: 512MB, type WB
reg 2, base: 3584MB, range: 512MB, type UC
total RAM covered: 4096M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 1G num_reg: 3 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 4GB, type WB
reg 1, base: 3584MB, range: 512MB, type UC
reg 2, base: 4GB, range: 512MB, type WB
e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
e820: last_pfn = 0xdff70 max_arch_pfn = 0x400000000
found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
Scanning 1 areas for low memory corruption
Base memory trampoline at [ffff880000096000] 96000 size 24576
init_memory_mapping: [mem 0x00000000-0x000fffff]
[mem 0x00000000-0x000fffff] page 4k
BRK [0x01fd1000, 0x01fd1fff] PGTABLE
BRK [0x01fd2000, 0x01fd2fff] PGTABLE
BRK [0x01fd3000, 0x01fd3fff] PGTABLE
init_memory_mapping: [mem 0x11fe00000-0x11fffffff]
[mem 0x11fe00000-0x11fffffff] page 2M
BRK [0x01fd4000, 0x01fd4fff] PGTABLE
init_memory_mapping: [mem 0x11c000000-0x11fdfffff]
[mem 0x11c000000-0x11fdfffff] page 2M
init_memory_mapping: [mem 0x100000000-0x11bffffff]
[mem 0x100000000-0x11bffffff] page 2M
init_memory_mapping: [mem 0x00100000-0xdff6ffff]
[mem 0x00100000-0x001fffff] page 4k
[mem 0x00200000-0xdfdfffff] page 2M
[mem 0xdfe00000-0xdff6ffff] page 4k
RAMDISK: [mem 0x350a0000-0x36847fff]
ACPI: RSDP 00000000000faff0 00024 (v02 ACPIAM)
ACPI: XSDT 00000000dff70100 0005C (v01 A_M_I_ OEMXSDT 05000926 MSFT 00000097)
ACPI: FACP 00000000dff70290 000F4 (v03 A_M_I_ OEMFACP 05000926 MSFT 00000097)
ACPI: DSDT 00000000dff70440 09722 (v01 A0991 A0991001 00000001 INTL 20060113)
ACPI: FACS 00000000dff7e000 00040
ACPI: APIC 00000000dff70390 0006C (v01 A_M_I_ OEMAPIC 05000926 MSFT 00000097)
ACPI: MCFG 00000000dff70400 0003C (v01 A_M_I_ OEMMCFG 05000926 MSFT 00000097)
ACPI: OEMB 00000000dff7e040 00089 (v01 A_M_I_ AMI_OEM 05000926 MSFT 00000097)
ACPI: HPET 00000000dff79b70 00038 (v01 A_M_I_ OEMHPET 05000926 MSFT 00000097)
ACPI: OSFR 00000000dff79bb0 000B0 (v01 A_M_I_ OEMOSFR 05000926 MSFT 00000097)
ACPI: SSDT 00000000dff7e9d0 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20060113)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at [mem 0x0000000000000000-0x000000011fffffff]
Initmem setup node 0 [mem 0x00000000-0x11fffffff]
NODE_DATA [mem 0x11fff7000-0x11fffbfff]
[ffffea0000000000-ffffea00047fffff] PMD -> [ffff88011b600000-ffff88011f5fffff] on node 0
Zone ranges:
DMA [mem 0x00001000-0x00ffffff]
DMA32 [mem 0x01000000-0xffffffff]
Normal [mem 0x100000000-0x11fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00001000-0x0009bfff]
node 0: [mem 0x00100000-0xdff6ffff]
node 0: [mem 0x100000000-0x11fffffff]
On node 0 totalpages: 1048331
DMA zone: 64 pages used for memmap
DMA zone: 21 pages reserved
DMA zone: 3995 pages, LIFO batch:0
DMA32 zone: 14270 pages used for memmap
DMA32 zone: 913264 pages, LIFO batch:31
Normal zone: 2048 pages used for memmap
Normal zone: 131072 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a301 base: 0xfed00000
smpboot: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: [mem 0x0009c000-0x0009cfff]
PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
PM: Registered nosave memory: [mem 0xdff70000-0xdff7dfff]
PM: Registered nosave memory: [mem 0xdff7e000-0xdffcffff]
PM: Registered nosave memory: [mem 0xdffd0000-0xdfffffff]
PM: Registered nosave memory: [mem 0xe0000000-0xfedfffff]
PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
PM: Registered nosave memory: [mem 0xfee01000-0xffdfffff]
PM: Registered nosave memory: [mem 0xffe00000-0xffffffff]
e820: [mem 0xe0000000-0xfedfffff] available for PCI devices
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 29 pages/cpu @ffff88011fc00000 s86720 r8192 d23872 u524288
pcpu-alloc: s86720 r8192 d23872 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Node order, mobility grouping on. Total pages: 1031928
Policy zone: Normal
PID hash table entries: 4096 (order: 3, 32768 bytes)
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 4020460K/4193324K available (7143K kernel code, 1082K rwdata, 3260K rodata, 1364K init, 1420K bss, 172864K reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
Offload RCU callbacks from all CPUs
Offload RCU callbacks from CPUs: 0-255.
NR_IRQS:16640 nr_irqs:712 16
Console: colour dummy device 80x25
console [tty0] enabled
allocated 16777216 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
tsc: Fast TSC calibration failed
tsc: PIT calibration matches HPET. 1 loops
tsc: Detected 3199.878 MHz processor
Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.75 BogoMIPS (lpj=12799512)
pid_max: default: 32768 minimum: 301
Security Framework initialized
AppArmor: AppArmor initialized
Yama: becoming mindful.
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
Initializing cgroup subsys hugetlb
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
tlb_flushall_shift: -1
Freeing SMP alternatives memory: 28K (ffffffff81e65000 - ffffffff81e6c000)
ACPI: Core revision 20130517
ACPI: All ACPI Tables successfully acquired
ftrace: allocating 27804 entries in 109 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
smpboot: CPU0: Intel(R) Core(TM)2 Quad CPU Q9450 @ 2.66GHz (fam: 06, model: 17, stepping: 07)
Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
smpboot: Booting Node 0, Processors #1 #2 #3 OK
Brought up 4 CPUs
smpboot: Total of 4 processors activated (25599.02 BogoMIPS)
devtmpfs: initialized
EVM: security.selinux
EVM: security.SMACK64
EVM: security.capability
PM: Registering ACPI NVS region [mem 0xdff7e000-0xdffcffff] (335872 bytes)
regulator-dummy: no parameters
RTC time: 10:45:24, date: 01/02/14
NET: Registered protocol family 16
ACPI: bus type PCI registered
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: SSDT 00000000dff7e0d0 00235 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00235 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
ACPI: SSDT 00000000dff7e310 00235 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00235 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
ACPI: SSDT 00000000dff7e550 00235 (v01 DpgPmm P003Ist 00000012 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00235 (v01 DpgPmm P003Ist 00000012 INTL 20060113)
ACPI: SSDT 00000000dff7e790 00235 (v01 DpgPmm P004Ist 00000012 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00235 (v01 DpgPmm P004Ist 00000012 INTL 20060113)
ACPI: Interpreter enabled
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130517/hwxface-571)
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: root bus resource [mem 0xf0000000-0xffffffff]
pci 0000:00:00.0: [8086:2e20] type 00 class 0x060000
DMAR: Forcing write-buffer flush capability
DMAR: Disabling IOMMU for graphics on this chipset
pci 0000:00:01.0: [8086:2e21] type 01 class 0x060400
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: System wakeup disabled by ACPI
pci 0000:00:1a.0: [8086:3a37] type 00 class 0x0c0300
pci 0000:00:1a.0: reg 0x20: [io 0xb800-0xb81f]
pci 0000:00:1a.0: System wakeup disabled by ACPI
pci 0000:00:1a.1: [8086:3a38] type 00 class 0x0c0300
pci 0000:00:1a.1: reg 0x20: [io 0xb880-0xb89f]
pci 0000:00:1a.1: System wakeup disabled by ACPI
pci 0000:00:1a.2: [8086:3a39] type 00 class 0x0c0300
pci 0000:00:1a.2: reg 0x20: [io 0xbc00-0xbc1f]
pci 0000:00:1a.2: System wakeup disabled by ACPI
pci 0000:00:1a.7: [8086:3a3c] type 00 class 0x0c0320
pci 0000:00:1a.7: reg 0x10: [mem 0xfcfffc00-0xfcffffff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: System wakeup disabled by ACPI
pci 0000:00:1b.0: [8086:3a3e] type 00 class 0x040300
pci 0000:00:1b.0: reg 0x10: [mem 0xfcff8000-0xfcffbfff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: [8086:3a40] type 01 class 0x060400
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: System wakeup disabled by ACPI
pci 0000:00:1c.4: [8086:3a48] type 01 class 0x060400
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: System wakeup disabled by ACPI
pci 0000:00:1c.5: [8086:3a4a] type 01 class 0x060400
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: System wakeup disabled by ACPI
pci 0000:00:1d.0: [8086:3a34] type 00 class 0x0c0300
pci 0000:00:1d.0: reg 0x20: [io 0xb080-0xb09f]
pci 0000:00:1d.0: System wakeup disabled by ACPI
pci 0000:00:1d.1: [8086:3a35] type 00 class 0x0c0300
pci 0000:00:1d.1: reg 0x20: [io 0xb400-0xb41f]
pci 0000:00:1d.1: System wakeup disabled by ACPI
pci 0000:00:1d.2: [8086:3a36] type 00 class 0x0c0300
pci 0000:00:1d.2: reg 0x20: [io 0xb480-0xb49f]
pci 0000:00:1d.2: System wakeup disabled by ACPI
pci 0000:00:1d.7: [8086:3a3a] type 00 class 0x0c0320
pci 0000:00:1d.7: reg 0x10: [mem 0xfcfff800-0xfcfffbff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
pci 0000:00:1e.0: System wakeup disabled by ACPI
pci 0000:00:1f.0: [8086:3a16] type 00 class 0x060100
pci 0000:00:1f.0: address space collision: [io 0x0800-0x087f] conflicts with ACPI CPU throttle [??? 0x00000810-0x00000815 flags 0x80000000]
pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 001f)
pci 0000:00:1f.2: [8086:3a22] type 00 class 0x010601
pci 0000:00:1f.2: reg 0x10: [io 0xac00-0xac07]
pci 0000:00:1f.2: reg 0x14: [io 0xa880-0xa883]
pci 0000:00:1f.2: reg 0x18: [io 0xa800-0xa807]
pci 0000:00:1f.2: reg 0x1c: [io 0xa480-0xa483]
pci 0000:00:1f.2: reg 0x20: [io 0xa400-0xa41f]
pci 0000:00:1f.2: reg 0x24: [mem 0xfcffe800-0xfcffefff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.3: [8086:3a30] type 00 class 0x0c0500
pci 0000:00:1f.3: reg 0x10: [mem 0xfcfff400-0xfcfff4ff 64bit]
pci 0000:00:1f.3: reg 0x20: [io 0x0400-0x041f]
pci 0000:01:00.0: [10de:11c6] type 00 class 0x030000
pci 0000:01:00.0: reg 0x10: [mem 0xfd000000-0xfdffffff]
pci 0000:01:00.0: reg 0x14: [mem 0xf0000000-0xf7ffffff 64bit pref]
pci 0000:01:00.0: reg 0x1c: [mem 0xf8000000-0xf9ffffff 64bit pref]
pci 0000:01:00.0: reg 0x24: [io 0xcc00-0xcc7f]
pci 0000:01:00.0: reg 0x30: [mem 0xfe900000-0xfe97ffff pref]
pci 0000:01:00.1: [10de:0e0b] type 00 class 0x040300
pci 0000:01:00.1: reg 0x10: [mem 0xfe9fc000-0xfe9fffff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:01.0: bridge window [mem 0xfd000000-0xfe9fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf9ffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 04]
pci 0000:00:1c.0: bridge window [mem 0xfbf00000-0xfbffffff 64bit pref]
pci 0000:03:00.0: [11ab:6121] type 00 class 0x01018f
pci 0000:03:00.0: reg 0x10: [io 0xec00-0xec07]
pci 0000:03:00.0: reg 0x14: [io 0xe880-0xe883]
pci 0000:03:00.0: reg 0x18: [io 0xe800-0xe807]
pci 0000:03:00.0: reg 0x1c: [io 0xe480-0xe483]
pci 0000:03:00.0: reg 0x20: [io 0xe400-0xe40f]
pci 0000:03:00.0: reg 0x24: [mem 0xfebffc00-0xfebfffff]
pci 0000:03:00.0: supports D1
pci 0000:03:00.0: PME# supported from D0 D1 D3hot
pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.4: PCI bridge to [bus 03]
pci 0000:00:1c.4: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.4: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:02:00.0: [11ab:4364] type 00 class 0x020000
pci 0000:02:00.0: reg 0x10: [mem 0xfeafc000-0xfeafffff 64bit]
pci 0000:02:00.0: reg 0x18: [io 0xd800-0xd8ff]
pci 0000:02:00.0: reg 0x30: [mem 0xfeac0000-0xfeadffff pref]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:1c.5: PCI bridge to [bus 02]
pci 0000:00:1c.5: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.5: bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xffffffff] (subtractive decode)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: Enabled 3 GPEs in block 00 to 3F
ACPI: \_SB_.PCI0: notify handler is installed
Found 1 acpi root devices
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:01:00.0
SCSI subsystem initialized
ACPI: bus type ATA registered
libata version 3.00 loaded.
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009cc00-0x0009ffff]
e820: reserve RAM buffer [mem 0xdff70000-0xdfffffff]
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
HPET: 4 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
Switched to clocksource hpet
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
ACPI: bus type PNP registered
system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:01: [dma 4]
pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
system 00:05: [io 0x0290-0x029f] has been reserved
system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:06: [io 0x04d0-0x04d1] has been reserved
system 00:06: [io 0x0800-0x087f] could not be reserved
system 00:06: [io 0x0500-0x057f] could not be reserved
system 00:06: [mem 0xfed08000-0xfed08fff] has been reserved
system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:06: [mem 0xfed50000-0xfed8ffff] has been reserved
system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:07: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:08: Plug and Play ACPI device, IDs INT0800 (active)
system 00:09: [mem 0xffc00000-0xffdfffff] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0a: [dma 0 disabled]
pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
system 00:0d: [mem 0xe0000000-0xefffffff] has been reserved
system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0e: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:0e: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0e: [mem 0x00100000-0xdfffffff] could not be reserved
system 00:0e: [mem 0xe0000000-0xffffffff] could not be reserved
system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 15 devices
ACPI: bus type PNP unregistered
pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 04] add_size 1000
pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 04] add_size 400000
pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000
pci 0000:00:1c.5: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
pci 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 400000
pci 0000:00:1c.4: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
pci 0000:00:1c.5: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
pci 0000:00:1c.0: BAR 14: assigned [mem 0xfa000000-0xfa3fffff]
pci 0000:00:1c.4: BAR 15: assigned [mem 0xfa400000-0xfa5fffff 64bit pref]
pci 0000:00:1c.5: BAR 15: assigned [mem 0xfa600000-0xfa7fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:01.0: bridge window [mem 0xfd000000-0xfe9fffff]
pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf9ffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 04]
pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
pci 0000:00:1c.0: bridge window [mem 0xfa000000-0xfa3fffff]
pci 0000:00:1c.0: bridge window [mem 0xfbf00000-0xfbffffff 64bit pref]
pci 0000:00:1c.4: PCI bridge to [bus 03]
pci 0000:00:1c.4: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.4: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1c.4: bridge window [mem 0xfa400000-0xfa5fffff 64bit pref]
pci 0000:00:1c.5: PCI bridge to [bus 02]
pci 0000:00:1c.5: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.5: bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:00:1c.5: bridge window [mem 0xfa600000-0xfa7fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 05]
pci 0000:00:1c.0: enabling device (0106 -> 0107)
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0xf0000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:01: resource 1 [mem 0xfd000000-0xfe9fffff]
pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf9ffffff 64bit pref]
pci_bus 0000:04: resource 0 [io 0x1000-0x1fff]
pci_bus 0000:04: resource 1 [mem 0xfa000000-0xfa3fffff]
pci_bus 0000:04: resource 2 [mem 0xfbf00000-0xfbffffff 64bit pref]
pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff]
pci_bus 0000:03: resource 2 [mem 0xfa400000-0xfa5fffff 64bit pref]
pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
pci_bus 0000:02: resource 2 [mem 0xfa600000-0xfa7fffff 64bit pref]
pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:05: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:05: resource 8 [mem 0xf0000000-0xffffffff]
NET: Registered protocol family 2
TCP established hash table entries: 32768 (order: 7, 524288 bytes)
TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP: reno registered
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
pci 0000:01:00.0: Boot video device
PCI: CLS 32 bytes, default 64
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 24224K (ffff8800350a0000 - ffff880036848000)
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB [mem 0xdbf70000-0xdff70000] (64MB) mapped at [ffff8800dbf70000-ffff8800dff6ffff]
Scanning for low memory corruption every 60 seconds
Initialise module verification
audit: initializing netlink socket (disabled)
type=2000 audit(1388659523.504:1): initialized
bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
zbud: loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
fuse init (API version 7.22)
msgmni has been set to 7899
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X
pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
intel_idle: does not run on family 6 model 23
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
ACPI: Requesting acpi_cpufreq
GHES: HEST is not enabled!
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Linux agpgart interface v0.103
brd: module loaded
loop: module loaded
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:1a.7: setting latency timer to 64
ehci-pci 0000:00:1a.7: EHCI Host Controller
ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:1a.7: debug port 1
ehci-pci 0000:00:1a.7: cache line size of 32 is not supported
ehci-pci 0000:00:1a.7: irq 18, io mem 0xfcfffc00
ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.11.0-14-generic ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci-pci 0000:00:1d.7: setting latency timer to 64
ehci-pci 0000:00:1d.7: EHCI Host Controller
ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci-pci 0000:00:1d.7: debug port 1
ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
ehci-pci 0000:00:1d.7: irq 23, io mem 0xfcfff800
ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 3.11.0-14-generic ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform: OHCI generic platform driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 3.11.0-14-generic uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 3.11.0-14-generic uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000bc00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 3.11.0-14-generic uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 3.11.0-14-generic uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 3.11.0-14-generic uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b480
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 3.11.0-14-generic uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
ledtrig-cpu: registered to indicate activity on CPUs
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Key type dns_resolver registered
PM: Hibernation image not present or could not be loaded.
Loading module verification certificates
MODSIGN: Loaded cert 'Magrathea: Glacier signing key: 4f57df1a3429640d83ffde722907e1377213486f'
registered taskstats version 1
Key type trusted registered
Key type encrypted registered
AppArmor: AppArmor sha1 policy hashing enabled
Magic number: 14:412:779
rtc_cmos 00:02: setting system clock to 2014-01-02 10:45:24 UTC (1388659524)
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
Freeing unused kernel memory: 1364K (ffffffff81d10000 - ffffffff81e65000)
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 1036K (ffff8800016fd000 - ffff880001800000)
Freeing unused kernel memory: 836K (ffff880001b2f000 - ffff880001c00000)
systemd-udevd[117]: starting version 204
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
libahci: module verification failed: signature and/or required key missing - tainting kernel
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ccc ems sxs
ahci 0000:00:1f.2: setting latency timer to 64
sky2: driver version 1.30
sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 3
sky2 0000:02:00.0: irq 45 for MSI/MSI-X
sky2 0000:02:00.0 eth0: addr 00:22:15:0a:c6:ce
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfcffe800 port 0xfcffe900 irq 44
ata2: SATA max UDMA/133 abar m2048@0xfcffe800 port 0xfcffe980 irq 44
ata3: SATA max UDMA/133 abar m2048@0xfcffe800 port 0xfcffea00 irq 44
ata4: SATA max UDMA/133 abar m2048@0xfcffe800 port 0xfcffea80 irq 44
ata5: SATA max UDMA/133 abar m2048@0xfcffe800 port 0xfcffeb00 irq 44
ata6: SATA max UDMA/133 abar m2048@0xfcffe800 port 0xfcffeb80 irq 44
usb 2-5: new high-speed USB device number 2 using ehci-pci
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 2-5: New USB device found, idVendor=05e3, idProduct=0608
usb 2-5: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-5: Product: USB2.0 Hub
hub 2-5:1.0: USB hub found
hub 2-5:1.0: 4 ports detected
ata1.00: ATA-8: OCZ-VERTEX2, 1.37, max UDMA/133
ata1.00: 117231408 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.37 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
usb 2-6: new high-speed USB device number 3 using ehci-pci
tsc: Refined TSC clocksource calibration: 3199.882 MHz
usb 2-6: New USB device found, idVendor=046d, idProduct=0802
usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=2
usb 2-6: SerialNumber: 8C557850
ata2: SATA link down (SStatus 0 SControl 300)
usb 4-1: new low-speed USB device number 2 using uhci_hcd
usb 4-1: New USB device found, idVendor=046d, idProduct=c00c
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: USB Optical Mouse
usb 4-1: Manufacturer: Logitech
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input3
hid-generic 0003:046D:C00C.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1a.1-1/input0
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-9: Samsung SSD 840 Series, DXT06B0Q, max UDMA/133
ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA Samsung SSD 840 DXT0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2
sd 2:0:0:0: [sdb] Attached SCSI disk
ata4: SATA link down (SStatus 0 SControl 300)
Switched to clocksource tsc
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi6 : pata_marvell
scsi7 : pata_marvell
ata7: PATA max UDMA/100 cmd 0xec00 ctl 0xe880 bmdma 0xe400 irq 16
ata8: PATA max UDMA/133 cmd 0xe800 ctl 0xe480 bmdma 0xe408 irq 16
ata7.01: ATAPI: HL-DT-ST DVDRAM GSA-H42L, SL01, max UDMA/66
ata7.01: configured for UDMA/66
scsi 6:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-H42L SL01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 6:0:1:0: Attached scsi CD-ROM sr0
sr 6:0:1:0: Attached scsi generic sg2 type 5
vesafb: mode is 1280x1024x32, linelength=5120, pages=0
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
mtrr: type mismatch for f9000000,800000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,400000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,200000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,100000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,80000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,40000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,20000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,10000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,8000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,4000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,2000 old: write-back new: write-combining
mtrr: type mismatch for f9000000,1000 old: write-back new: write-combining
vesafb: framebuffer at 0xf9000000, mapped to 0xffffc90010800000, using 5120k, total 5120k
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
EXT4-fs (sda1): INFO: recovery required on readonly filesystem
EXT4-fs (sda1): write access will be enabled during recovery
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
Adding 4095996k swap on /dev/sdb2. Priority:-1 extents:1 across:4095996k SSFS
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
systemd-udevd[346]: starting version 204
lp: driver loaded but no devices found
[drm] Initialized drm 1.1.0 20060810
w83627ehf: Found W83667HG chip at 0x290
ACPI Warning: 0x0000000000000295-0x0000000000000296 SystemIO conflicts with Region \_SB_.PCI0.SBRG.SIOR.HWRE 1 (20130517/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI Warning: 0x0000000000000828-0x000000000000082f SystemIO conflicts with Region \PMRG 1 (20130517/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPS0 1 (20130517/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPS0 1 (20130517/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting gpio_ich
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[drm] Initialized nvidia-drm 0.0.0 20130102 for 0000:01:00.0 on minor 0
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 331.20 Wed Oct 30 17:43:35 PDT 2013
snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
microcode: CPU0 sig=0x10677, pf=0x10, revision=0x705
EXT4-fs (sda1): re-mounted. Opts: discard,errors=remount-ro
type=1400 audit(1388659529.101:2): apparmor="STATUS" operation="profile_load" parent=396 profile="unconfined" name="/sbin/dhclient" pid=426 comm="apparmor_parser"
type=1400 audit(1388659529.101:3): apparmor="STATUS" operation="profile_load" parent=396 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=426 comm="apparmor_parser"
type=1400 audit(1388659529.101:4): apparmor="STATUS" operation="profile_load" parent=396 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=426 comm="apparmor_parser"
type=1400 audit(1388659529.105:5): apparmor="STATUS" operation="profile_replace" parent=396 profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=426 comm="apparmor_parser"
type=1400 audit(1388659529.105:6): apparmor="STATUS" operation="profile_replace" parent=396 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=426 comm="apparmor_parser"
type=1400 audit(1388659529.105:7): apparmor="STATUS" operation="profile_replace" parent=396 profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=426 comm="apparmor_parser"
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device (046d:0802)
input: UVC Camera (046d:0802) as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6:1.0/input/input4
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: discard,errors=remount-ro
FS-Cache: Loaded
FS-Cache: Netfs 'cifs' registered for caching
Key type cifs.spnego registered
Key type cifs.idmap registered
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: cifs_mount failed w/return code = -101
microcode: CPU1 sig=0x10677, pf=0x10, revision=0x705
microcode: CPU2 sig=0x10677, pf=0x10, revision=0x705
microcode: CPU3 sig=0x10677, pf=0x10, revision=0x705
microcode: Microcode Update Driver: v2.00 , Peter Oruba
usb_audio: Warning! Unlikely big volume range (=6144), cval->res is probably wrong.
usb_audio: [5] FU [Mic Capture Volume] ch = 1, val = 1536/7680/1[ 5.503907] usbcore: registered new interface driver snd-usb-audio
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
hda_intel: Disabling MSI
hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
hda-intel 0000:01:00.1: Disabling 64bit DMA
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
hda-intel 0000:01:00.1: Enable delay in RIRB handling
init: failsafe main process (595) killed by TERM signal
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
init: avahi-cups-reload main process (773) terminated with status 1
ppdev: user-space parallel port driver
type=1400 audit(1388659529.589:8): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-freerdp/freerdp-session-wrapper" pid=819 comm="apparmor_parser"
type=1400 audit(1388659529.589:9): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="chromium_browser" pid=819 comm="apparmor_parser"
type=1400 audit(1388659529.589:10): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=818 comm="apparmor_parser"
type=1400 audit(1388659529.589:11): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="chromium_browser" pid=818 comm="apparmor_parser"
type=1400 audit(1388659529.593:12): apparmor="STATUS" operation="profile_replace" parent=813 profile="unconfined" name="chromium_browser" pid=818 comm="apparmor_parser"
type=1400 audit(1388659529.597:13): apparmor="STATUS" operation="profile_replace" parent=813 profile="unconfined" name="chromium_browser" pid=819 comm="apparmor_parser"
type=1400 audit(1388659529.601:14): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="/usr/bin/evince" pid=822 comm="apparmor_parser"
type=1400 audit(1388659529.601:15): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="sanitized_helper" pid=822 comm="apparmor_parser"
type=1400 audit(1388659529.601:16): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="/usr/bin/evince-previewer" pid=822 comm="apparmor_parser"
type=1400 audit(1388659529.601:17): apparmor="STATUS" operation="profile_load" parent=813 profile="unconfined" name="sanitized_helper" pid=822 comm="apparmor_parser"
sky2 0000:02:00.0 eth0: enabling interface
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input5
input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input6
input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input7
input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input8
init: anacron main process (1010) terminated with status 1
init: atd main process (1005) terminated with status 1
init: atd main process ended, respawning
init: nvidia-persistenced main process (1073) terminated with status 1
init: gdm main process (1050) killed by TERM signal
nvidia 0000:01:00.0: irq 47 for MSI/MSI-X
NVRM: Your system is not currently configured to drive a VGA console
NVRM: on the primary VGA device. The NVIDIA Linux graphics driver
NVRM: requires the use of a text-mode VGA console. Use of other console
NVRM: drivers including, but not limited to, vesafb, may result in
NVRM: corruption and stability problems, and is not supported.
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: cifs_mount failed w/return code = -101
CIFS VFS: Error connecting to socket. Aborting operation.
CIFS VFS: cifs_mount failed w/return code = -101
sky2 0000:02:00.0 eth0: Link is up at 1000 Mbps, full duplex, flow control both
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
init: anacron main process (1504) terminated with status 1
init: plymouth-stop pre-start process (2356) terminated with status 1
perf samples too long (2502 > 2500), lowering kernel.perf_event_max_sample_rate to 50000