dmesg - info11
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32-358.18.1.el6.x86_64 (mockbuild@c6b10.bsys.dev.centos.org) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Wed Aug 28 17:19:38 UTC 2013
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000be7b1d00 (usable)
BIOS-e820: 00000000be7b1d00 - 00000000be7b3d00 (ACPI NVS)
BIOS-e820: 00000000be7b3d00 - 00000000bf000000 (reserved)
BIOS-e820: 00000000f4000000 - 00000000f8000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed40000 (reserved)
BIOS-e820: 00000000fed45000 - 0000000100000000 (reserved)
DMI 2.4 present.
SMBIOS version 2.4 @ 0xF9C00
DMI: Hewlett-Packard HP Compaq dc7700 Convertible Minitower/0A58h, BIOS 786E1 v01.10 04/13/2007
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0xbe7b1 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-E3FFF write-protect
E4000-EFFFF write-back
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FC0000000 write-back
2 base 0BE800000 mask FFF800000 uncachable
3 base 0BF000000 mask FFF000000 uncachable
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3048MB, range: 8MB, type UC
reg 3, base: 3056MB, range: 16MB, type UC
total RAM covered: 3048M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 32M num_reg: 4 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3048MB, range: 8MB, type UC
reg 3, base: 3056MB, range: 16MB, type UC
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000be7b1000
0000000000 - 00be600000 page 2M
00be600000 - 00be7b1000 page 4k
kernel direct mapping tables up to be7b1000 @ 8000-d000
RAMDISK: 37027000 - 37fef87f
ACPI: RSDP 00000000000e7610 00014 (v00 COMPAQ)
ACPI: RSDT 00000000be7c3d40 00040 (v01 HPQOEM SLIC-BPC 20070413 00000000)
ACPI: FACP 00000000be7c3de8 00074 (v01 COMPAQ BROADH2O 00000001 00000000)
ACPI: DSDT 00000000be7c4143 096B7 (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
ACPI: FACS 00000000be7c3d00 00040
ACPI: APIC 00000000be7c3e5c 00068 (v01 COMPAQ BROADH2O 00000001 00000000)
ACPI: ASF! 00000000be7c3ec4 00063 (v32 COMPAQ BROADH2O 00000001 00000000)
ACPI: MCFG 00000000be7c3f27 0003C (v01 COMPAQ BROADH2O 00000001 00000000)
ACPI: TCPA 00000000be7c3f63 00032 (v01 COMPAQ BROADH2O 00000001 00000000)
ACPI: SLIC 00000000be7c3f95 00176 (v01 HPQOEM SLIC-BPC 00000001 00000000)
ACPI: HPET 00000000be7c410b 00038 (v01 COMPAQ BROADH2O 00000001 00000000)
ACPI: Local APIC address 0xfee00000
Setting APIC routing to flat.
No NUMA configuration found
Faking a node at 0000000000000000-00000000be7b1000
Bootmem setup node 0 0000000000000000-00000000be7b1000
NODE_DATA [000000000000b000 - 000000000003efff]
bootmap [000000000003f000 - 0000000000056cf7] pages 18
(7 early reservations) ==> bootmem [0000000000 - 00be7b1000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 000201b0a4] TEXT DATA BSS ==> [0001000000 - 000201b0a4]
#3 [0037027000 - 0037fef87f] RAMDISK ==> [0037027000 - 0037fef87f]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [000201c000 - 000201c0f6] BRK ==> [000201c000 - 000201c0f6]
#6 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000]
found SMP MP-table at [ffff8800000f9bf0] f9bf0
Reserving 129MB of memory at 48MB for crashkernel (System RAM: 3047MB)
[ffffea0000000000-ffffea00009fffff] PMD -> [ffff880002600000-ffff880002ffffff] on node 0
[ffffea0000a00000-ffffea00029fffff] PMD -> [ffff88000b200000-ffff88000d1fffff] on node 0
Zone PFN ranges:
DMA 0x00000001 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000001 -> 0x0000009f
0: 0x00000100 -> 0x000be7b1
On node 0 totalpages: 780111
DMA zone: 56 pages used for memmap
DMA zone: 102 pages reserved
DMA zone: 3840 pages, LIFO batch:0
DMA32 zone: 10611 pages used for memmap
DMA32 zone: 765502 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0xf808
ACPI: Local APIC address 0xfee00000
Setting APIC routing to flat.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e8000
PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
Allocating PCI resources starting at bf000000 (gap: bf000000:35000000)
Booting paravirtualized kernel on bare hardware
NR_CPUS:4096 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 31 pages/cpu @ffff880002200000 s94552 r8192 d24232 u1048576
pcpu-alloc: s94552 r8192 d24232 u1048576 alloc=1*2097152
pcpu-alloc: [0] 0 1
Built 1 zonelists in Node order, mobility grouping on. Total pages: 769342
Policy zone: DMA32
PID hash table entries: 4096 (order: 3, 32768 bytes)
Checking aperture...
No AGP bridge found
Memory: 2911920k/3120836k available (5222k kernel code, 392k absent, 208524k reserved, 7119k data, 1264k init)
Hierarchical RCU implementation.
NR_IRQS:33024 nr_irqs:424
Console: colour VGA+ 80x25
console [tty0] enabled
allocated 12582912 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2393.949 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4787.89 BogoMIPS (lpj=2393949)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
Initializing cgroup subsys net_prio
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20090903
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 21439 entries in 85 pages
APIC routing finalized to flat.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Performance Events: PEBS fmt0-, Core2 events, Intel PMU driver.
PEBS disabled due to CPU errata.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1 Ok.
Brought up 2 CPUs
Total of 2 processors activated (9575.79 BogoMIPS).
sizeof(vma)=200 bytes
sizeof(page)=56 bytes
sizeof(inode)=592 bytes
sizeof(dentry)=192 bytes
sizeof(ext3inode)=800 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=232 bytes
sizeof(task_struct)=2648 bytes
devtmpfs: initialized
PM: Registering ACPI NVS region at be7b1d00 (8192 bytes)
regulator: core version 0.5
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f4000000 segment 0 buses 0 - 63
PCI: MCFG area at f4000000 reserved in E820
PCI: Using MMCONFIG at f4000000 - f7ffffff
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
HEST: Table not found.
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI Error (dsfield-0143): [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff8800bcf44858), AE_ALREADY_EXISTS
ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20090903/nspredef-336)
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A08:00: host bridge window [mem 0xf8000000-0xfebfffff] (ignored)
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A08:00: host bridge window [io 0x1000-0x2fff] (ignored)
pci_root PNP0A08:00: host bridge window [io 0x3000-0x6fff] (ignored)
pci_root PNP0A08:00: host bridge window [io 0x7000-0xafff] (ignored)
pci_root PNP0A08:00: host bridge window [io 0xb000-0xffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0xbf000000-0xf3ffffff] (ignored)
pci 0000:00:02.0: reg 10: [mem 0xf0400000-0xf04fffff]
pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
pci 0000:00:02.0: reg 20: [io 0x1100-0x1107]
pci 0000:00:03.0: reg 10: [mem 0xf0525900-0xf052590f 64bit]
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:19.0: reg 10: [mem 0xf0500000-0xf051ffff]
pci 0000:00:19.0: reg 14: [mem 0xf0524000-0xf0524fff]
pci 0000:00:19.0: reg 18: [io 0x1000-0x101f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20: [io 0x1020-0x103f]
pci 0000:00:1a.1: reg 20: [io 0x1040-0x105f]
pci 0000:00:1a.7: reg 10: [mem 0xf0525000-0xf05253ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10: [mem 0xf0520000-0xf0523fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.0: reg 20: [io 0x1060-0x107f]
pci 0000:00:1d.1: reg 20: [io 0x1080-0x109f]
pci 0000:00:1d.7: reg 10: [mem 0xf0525400-0xf05257ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io 0xf800-0xf87f] claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0xfa00-0xfa3f] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0400 (mask 007f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0480 (mask 000f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0cb0 (mask 000f)
pci 0000:00:1f.2: reg 10: [io 0x1108-0x110f]
pci 0000:00:1f.2: reg 14: [io 0x1118-0x111b]
pci 0000:00:1f.2: reg 18: [io 0x1110-0x1117]
pci 0000:00:1f.2: reg 1c: [io 0x111c-0x111f]
pci 0000:00:1f.2: reg 20: [io 0x10e0-0x10ef]
pci 0000:00:1f.2: reg 24: [io 0x10f0-0x10ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1c.0: PCI bridge to [bus 20-20]
pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
ACPI Error (dsfield-0143): [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff8800bcf44858), AE_ALREADY_EXISTS
ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20090903/nspredef-336)
pci0000:00: Requesting ACPI _OSC control (0x1d)
ACPI Error (dsfield-0143): [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff8800bcf44858), AE_ALREADY_EXISTS
ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20090903/nspredef-336)
Unable to assume _OSC PCIe control. Disabling ASPM
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:00:02.0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: old code would have set cacheline size to 32 bytes, but clflush_size = 64
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [io 0x00f0-0x00ff]
pnp 00:01: [irq 13]
pnp 00:01: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:02: [io 0x0000-0x000f]
pnp 00:02: [io 0x0080-0x008f]
pnp 00:02: [io 0x00c0-0x00df]
pnp 00:02: [dma 4]
pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:03: [io 0x0070-0x0071]
pnp 00:03: [irq 8]
pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:04: [io 0x0061]
pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:05: [irq 12]
pnp 00:05: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
pnp 00:06: [io 0x0060]
pnp 00:06: [io 0x0064]
pnp 00:06: [irq 1]
pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:07: [irq 7]
pnp 00:07: [dma 3]
pnp 00:07: [io 0x0378-0x037f]
pnp 00:07: [io 0x0778-0x077d]
pnp 00:07: Plug and Play ACPI device, IDs PNP0401 (active)
pnp 00:08: [irq 4]
pnp 00:08: [io 0x03f8-0x03ff]
pnp 00:08: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
pnp 00:09: [irq 6]
pnp 00:09: [dma 2]
pnp 00:09: [io 0x03f0-0x03f5]
pnp 00:09: [io 0x03f7]
pnp 00:09: Plug and Play ACPI device, IDs PNP0700 (active)
pnp 00:0a: [mem 0xfec00000-0xfec00fff]
pnp 00:0a: Plug and Play ACPI device, IDs PNP0003 (active)
pnp 00:0b: [mem 0xfed00000-0xfed003ff]
pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:0c: [io 0x0010-0x001f]
pnp 00:0c: [io 0x0050-0x0053]
pnp 00:0c: [io 0x0072-0x0077]
pnp 00:0c: [io 0x0090-0x009f]
pnp 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0d: [io 0x0400-0x041f]
pnp 00:0d: [io 0x0420-0x043f]
pnp 00:0d: [io 0x0440-0x045f]
pnp 00:0d: [io 0x0460-0x047f]
pnp 00:0d: [io 0x0480-0x048f]
pnp 00:0d: [io 0xf800-0xf81f]
pnp 00:0d: [io 0xf820-0xf83f]
pnp 00:0d: [io 0xf840-0xf85f]
pnp 00:0d: [io 0xf860-0xf87f]
pnp 00:0d: [io 0xfa00-0xfa3f]
pnp 00:0d: [io 0xfc00-0xfc7f]
pnp 00:0d: [io 0xfc80-0xfcff]
pnp 00:0d: [io 0xfe00-0xfe7f]
pnp 00:0d: [io 0xfe80-0xfeff]
pnp 00:0d: disabling [io 0xf800-0xf81f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
pnp 00:0d: disabling [io 0xf820-0xf83f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
pnp 00:0d: disabling [io 0xf840-0xf85f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
pnp 00:0d: disabling [io 0xf860-0xf87f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
pnp 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0e: [io 0x004e-0x004f]
pnp 00:0e: [io 0x04d0-0x04d1]
pnp 00:0e: [io 0x0cb0-0x0cbf]
pnp 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0f: [mem 0x00000000-0x0009ffff]
pnp 00:0f: [mem 0x00100000-0xbeffffff]
pnp 00:0f: [mem 0x000e4000-0x000fffff]
pnp 00:0f: [mem 0xfec01000-0xfecfffff]
pnp 00:0f: [mem 0xfed00400-0xfed3ffff]
pnp 00:0f: [mem 0xfed40000-0xffffffff]
pnp 00:0f: [mem 0xf4000000-0xf7ffffff]
pnp 00:0f: [mem 0x000cd000-0x000e3fff]
pnp 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
system 00:0d: [io 0x0400-0x041f] has been reserved
system 00:0d: [io 0x0420-0x043f] has been reserved
system 00:0d: [io 0x0440-0x045f] has been reserved
system 00:0d: [io 0x0460-0x047f] has been reserved
system 00:0d: [io 0x0480-0x048f] has been reserved
system 00:0d: [io 0xfa00-0xfa3f] has been reserved
system 00:0d: [io 0xfc00-0xfc7f] has been reserved
system 00:0d: [io 0xfc80-0xfcff] has been reserved
system 00:0d: [io 0xfe00-0xfe7f] has been reserved
system 00:0d: [io 0xfe80-0xfeff] has been reserved
system 00:0e: [io 0x04d0-0x04d1] has been reserved
system 00:0e: [io 0x0cb0-0x0cbf] has been reserved
system 00:0f: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0f: [mem 0x00100000-0xbeffffff] could not be reserved
system 00:0f: [mem 0x000e4000-0x000fffff] could not be reserved
system 00:0f: [mem 0xfec01000-0xfecfffff] has been reserved
system 00:0f: [mem 0xfed00400-0xfed3ffff] has been reserved
system 00:0f: [mem 0xfed40000-0xffffffff] could not be reserved
system 00:0f: [mem 0xf4000000-0xf7ffffff] has been reserved
system 00:0f: [mem 0x000cd000-0x000e3fff] has been reserved
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:1c.0: BAR 14: assigned [mem 0xc0000000-0xc01fffff]
pci 0000:00:1c.0: BAR 15: assigned [mem 0xc0200000-0xc03fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
pci 0000:00:1c.0: PCI bridge to [bus 20-20]
pci 0000:00:1c.0: PCI bridge to [bus 20-20]
pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:1c.0: bridge window [mem 0xc0000000-0xc01fffff]
pci 0000:00:1c.0: bridge window [mem 0xc0200000-0xc03fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 07-07]
pci 0000:00:1e.0: PCI bridge to [bus 07-07]
pci 0000:00:1e.0: bridge window [io disabled]
pci 0000:00:1e.0: bridge window [mem disabled]
pci 0000:00:1e.0: bridge window [mem pref disabled]
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
pci_bus 0000:20: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:20: resource 1 [mem 0xc0000000-0xc01fffff]
pci_bus 0000:20: resource 2 [mem 0xc0200000-0xc03fffff 64bit pref]
pci_bus 0000:07: resource 4 [io 0x0000-0xffff]
pci_bus 0000:07: resource 5 [mem 0x00000000-0xfffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
alloc irq_desc for 20 on node -1
alloc kstat_irqs on node -1
pci 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1a.0: PCI INT A disabled
alloc irq_desc for 21 on node -1
alloc kstat_irqs on node -1
pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
pci 0000:00:1a.1: PCI INT B disabled
alloc irq_desc for 22 on node -1
alloc kstat_irqs on node -1
pci 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
pci 0000:00:1a.7: PCI INT C disabled
pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1d.0: PCI INT A disabled
pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
pci 0000:00:1d.1: PCI INT B disabled
pci 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1d.7: PCI INT A disabled
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 16162k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1384165109.429:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 5718
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
ksign: Installing public key data
Loading keyring
- Added public key 2B202C2FC9DD26CD
- User ID: CentOS (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: setting latency timer to 64
alloc irq_desc for 24 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
intel_idle: MWAIT substates: 0x20
intel_idle: does not run on family 6 model 15
ipmi message handler version 39.2
IPMI System Interface driver.
ipmi_si: Adding default-specified kcs state machine
ipmi_si: Trying default-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
ipmi_si: Interface detection failed
ipmi_si: Adding default-specified smic state machine
ipmi_si: Trying default-specified smic state machine at i/o address 0xca9, slave address 0x0, irq 0
ipmi_si: Interface detection failed
ipmi_si: Adding default-specified bt state machine
ipmi_si: Trying default-specified bt state machine at i/o address 0xe4, slave address 0x0, irq 0
ipmi_si: Interface detection failed
ipmi_si: Unable to find any System Interface(s)
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PBTN]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
ACPI: acpi_idle registered with cpuidle
ACPI: SSDT 00000000be7ce637 00320 (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
ERST: Table is not found!
GHES: HEST is not enabled!
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 965Q Chipset
agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
agpgart-intel 0000:00:00.0: detected 8192K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
crash memory driver: version 1.1
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.7: irq 22, io mem 0xf0525000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32-358.18.1.el6.x86_64 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf0525400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32-358.18.1.el6.x86_64 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001020
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32-358.18.1.el6.x86_64 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001040
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.32-358.18.1.el6.x86_64 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001060
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.32-358.18.1.el6.x86_64 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001080
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.32-358.18.1.el6.x86_64 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.1
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
registered taskstats version 1
rtc_cmos 00:03: setting system clock to 2013-11-11 10:18:30 UTC (1384165110)
Initalizing network drop monitor service
Freeing unused kernel memory: 1264k freed
Write protecting the kernel read-only data: 10240k
Freeing unused kernel memory: 900k freed
Freeing unused kernel memory: 1672k freed
dracut: dracut-004-303.el6
dracut: rd_NO_LUKS: removing cryptoluks activation
dracut: rd_NO_LVM: removing LVM activation
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.23.6-ioctl (2012-07-25) initialised: dm-devel@redhat.com
udev: starting version 147
[drm] Initialized drm 1.1.0 20060810
alloc irq_desc for 16 on node -1
alloc kstat_irqs on node -1
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
alloc irq_desc for 25 on node -1
alloc kstat_irqs on node -1
i915 0000:00:02.0: irq 25 for MSI/MSI-X
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] Driver supports precise vblank timestamp query.
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm] initialized overlay support
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 160x64
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
Slow work thread pool: Starting up
Slow work thread pool: Ready
ACPI Exception: AE_NOT_FOUND, Evaluating _DOD (20090903/video-1917)
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
ACPI: Video Device [GFX0] (multi-head: no rom: yes post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
dracut: Starting plymouth daemon
usb 5-1: new low speed USB device number 2 using uhci_hcd
dracut: rd_NO_DM: removing DM RAID activation
dracut: rd_NO_MD: removing MD RAID activation
ata_piix 0000:00:1f.2: version 2.13
alloc irq_desc for 18 on node -1
alloc kstat_irqs on node -1
ata_piix 0000:00:1f.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
usb 5-1: New USB device found, idVendor=413c, idProduct=2106
usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: Dell QuietKey Keyboard
usb 5-1: Manufacturer: DELL
usb 5-1: configuration #1 chosen from 1 choice
input: DELL Dell QuietKey Keyboard as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input4
generic-usb 0003:413C:2106.0001: input,hidraw0: USB HID v1.10 Keyboard [DELL Dell QuietKey Keyboard] on usb-0000:00:1d.0-1/input0
Refined TSC clocksource calibration: 2393.999 MHz.
Switching to clocksource tsc
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x10e0 irq 14
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x10e8 irq 15
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.01: SATA link down (SStatus 0 SControl 300)
ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.01: SATA link down (SStatus 0 SControl 300)
ata2.01: link offline, clearing class 3 to NONE
ata1.00: ATA-7: ST3250820AS, 3.CHL, max UDMA/100
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: ATAPI: HL-DT-STDVD+-RW GSA-H31L, W618, max UDMA/100
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3250820AS 3.CH PQ: 0 ANSI: 5
ata2.00: configured for UDMA/100
scsi 1:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-H31L W618 PQ: 0 ANSI: 5
ACPI: WMI: Mapper loaded
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
dracut: Mounted root filesystem /dev/sda1
dracut: Loading SELinux policy
type=1404 audit(1384165112.815:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 2048 avtab hash slots, 278017 rules.
SELinux: 2048 avtab hash slots, 278017 rules.
SELinux: 9 users, 12 roles, 3900 types, 205 bools, 1 sens, 1024 cats
SELinux: 81 classes, 278017 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda1, type ext2), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1384165113.584:3): policy loaded auid=4294967295 ses=4294967295
dracut:
dracut: Switching root
readahead: starting
udev: starting version 147
e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
alloc irq_desc for 19 on node -1
alloc kstat_irqs on node -1
e1000e 0000:00:19.0: PCI INT B -> GSI 19 (level, low) -> IRQ 19
e1000e 0000:00:19.0: setting latency timer to 64
e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
alloc irq_desc for 26 on node -1
alloc kstat_irqs on node -1
e1000e 0000:00:19.0: irq 26 for MSI/MSI-X
e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:0f:fe:57:ad:c2
e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:00:19.0: eth0: MAC: 6, PHY: 6, PBA No: 1002FF-0FF
snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
alloc irq_desc for 27 on node -1
alloc kstat_irqs on node -1
snd_hda_intel 0000:00:1b.0: irq 27 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: setting latency timer to 64
hda_codec: ALC262: SKU not ready 0x411111f0
input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07rh
iTCO_wdt: Found a ICH8DO TCO device (Version=2, TCOBASE=0xf860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
microcode: CPU0 sig=0x6f6, pf=0x1, revision=0xc6
platform microcode: firmware: requesting intel-ucode/06-0f-06
microcode: CPU1 sig=0x6f6, pf=0x1, revision=0xc6
platform microcode: firmware: requesting intel-ucode/06-0f-06
Microcode Update Driver: v2.00 , Peter Oruba
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
microcode: CPU0 updated to revision 0xd0, date = 2010-09-30
microcode: CPU1 updated to revision 0xd0, date = 2010-09-30
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
ppdev: user-space parallel port driver
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
Adding 2047992k swap on /dev/sda2. Priority:-1 extents:1 across:2047992k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
e1000e 0000:00:19.0: irq 26 for MSI/MSI-X
e1000e 0000:00:19.0: irq 26 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
Bridge firewalling registered
device virbr0-nic entered promiscuous mode
virbr0: starting userspace STP failed, starting kernel STP
device virbr1-nic entered promiscuous mode
virbr1: starting userspace STP failed, starting kernel STP
Ebtables v2.0 registered
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
lo: Disabled Privacy Extensions
SELinux: initialized (dev proc, type proc), uses genfs_contexts
hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
fuse init (API version 7.13)
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts