dmesg - cfq
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32-358.23.2.el6.x86_64 (mockbuild@c6b9.bsys.dev.centos.org) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Wed Oct 16 18:37:12 UTC 2013
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000099c00 (usable)
BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007de72000 (usable)
BIOS-e820: 000000007de72000 - 000000007deb1000 (reserved)
BIOS-e820: 000000007deb1000 - 000000007dfba000 (ACPI data)
BIOS-e820: 000000007dfba000 - 000000007e1d4000 (ACPI NVS)
BIOS-e820: 000000007e1d4000 - 000000007f381000 (reserved)
BIOS-e820: 000000007f381000 - 000000007f800000 (ACPI NVS)
BIOS-e820: 0000000080000000 - 0000000090000000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed40000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000c80000000 (usable)
DMI 2.7 present.
SMBIOS version 2.7 @ 0xF04D0
DMI: Supermicro SSG-6037R-E1R16N/X9DRi-LN4+/X9DR3-LN4+, BIOS 3.0 07/05/2013
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0xc80000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000000 mask 3FF800000000 write-back
1 base 000800000000 mask 3FFC00000000 write-back
2 base 000C00000000 mask 3FFF80000000 write-back
3 base 000080000000 mask 3FFF80000000 uncachable
4 disabled
5 disabled
6 disabled
7 disabled
8 disabled
9 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 32GB, type WB
reg 1, base: 32GB, range: 16GB, type WB
reg 2, base: 48GB, range: 2GB, type WB
reg 3, base: 2GB, range: 2GB, type UC
total RAM covered: 49152M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 64K num_reg: 6 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 4GB, range: 4GB, type WB
reg 2, base: 8GB, range: 8GB, type WB
reg 3, base: 16GB, range: 16GB, type WB
reg 4, base: 32GB, range: 16GB, type WB
reg 5, base: 48GB, range: 2GB, type WB
e820 update range: 0000000080000000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0x7de72 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
Using GB pages for direct mapping
init_memory_mapping: 0000000000000000-000000007de72000
0000000000 - 0040000000 page 1G
0040000000 - 007de00000 page 2M
007de00000 - 007de72000 page 4k
kernel direct mapping tables up to 7de72000 @ 10000-13000
init_memory_mapping: 0000000100000000-0000000c80000000
0100000000 - 0c80000000 page 1G
kernel direct mapping tables up to c80000000 @ 12000-13000
RAMDISK: 371e9000 - 37fefb43
ACPI: RSDP 00000000000f04a0 00024 (v02 SUPERM)
ACPI: XSDT 000000007dee7088 0008C (v01 SUPERM SMCI--MB 00000001 AMI 00010013)
ACPI: FACP 000000007def1ac8 000F4 (v04 SUPERM SMCI--MB 00000001 AMI 00010013)
ACPI: DSDT 000000007dee71a0 0A924 (v02 SUPERM SMCI--MB 00000000 INTL 20091112)
ACPI: FACS 000000007e1cb080 00040
ACPI: APIC 000000007def1bc0 00090 (v03 00000001 AMI 00010013)
ACPI: FPDT 000000007def1c50 00044 (v01 00000001 AMI 00010013)
ACPI: HPET 000000007def1c98 00038 (v01 SUPERM SMCI--MB 00000001 AMI. 00000005)
ACPI: PRAD 000000007def1cd0 000BE (v02 PRADID PRADTID 00000001 MSFT 04000000)
ACPI: SPMI 000000007def1d90 00040 (v05 A M I OEMSPMI 00000000 AMI. 00000000)
ACPI: SSDT 000000007def1dd0 C7AE8 (v02 INTEL CpuPm 00004000 INTL 20091112)
ACPI: EINJ 000000007dfb98b8 00130 (v01 AMI AMI EINJ 00000000 00000000)
ACPI: ERST 000000007dfb99e8 00230 (v01 AMIER AMI ERST 00000000 00000000)
ACPI: HEST 000000007dfb9c18 000A8 (v01 AMI AMI HEST 00000000 00000000)
ACPI: BERT 000000007dfb9cc0 00030 (v01 AMI AMI BERT 00000000 00000000)
ACPI: DMAR 000000007dfb9cf0 000BC (v01 A M I OEMDMAR 00000001 INTL 00000001)
ACPI: MCFG 000000007dfb9db0 0003C (v01 SUPERM SMCI--MB 00000001 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
Setting APIC routing to flat.
No NUMA configuration found
Faking a node at 0000000000000000-0000000c80000000
Bootmem setup node 0 0000000000000000-0000000c80000000
NODE_DATA [0000000000012000 - 0000000000045fff]
bootmap [0000000000100000 - 000000000028ffff] pages 190
(7 early reservations) ==> bootmem [0000000000 - 0c80000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 000201b0e4] TEXT DATA BSS ==> [0001000000 - 000201b0e4]
#3 [00371e9000 - 0037fefb43] RAMDISK ==> [00371e9000 - 0037fefb43]
#4 [0000099c00 - 0000100000] BIOS reserved ==> [0000099c00 - 0000100000]
#5 [000201c000 - 000201c674] BRK ==> [000201c000 - 000201c674]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
found SMP MP-table at [ffff8800000fd8c0] fd8c0
Reserving 132MB of memory at 48MB for crashkernel (System RAM: 51200MB)
[ffffea0000000000-ffffea00105fffff] PMD -> [ffff880028600000-ffff880036ffffff] on node 0
[ffffea0010600000-ffffea002bbfffff] PMD -> [ffff880038000000-ffff8800535fffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00c80000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x00000099
0: 0x00000100 -> 0x0007de72
0: 0x00100000 -> 0x00c80000
On node 0 totalpages: 12574203
DMA zone: 56 pages used for memmap
DMA zone: 107 pages reserved
DMA zone: 3814 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 497322 pages, LIFO batch:31
Normal zone: 164864 pages used for memmap
Normal zone: 11893760 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
Setting APIC routing to flat.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x02] address[0xfec01000] gsi_base[24])
IOAPIC[1]: apic_id 2, version 32, address 0xfec01000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 48
PM: Registered nosave memory: 0000000000099000 - 000000000009a000
PM: Registered nosave memory: 000000000009a000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 000000007de72000 - 000000007deb1000
PM: Registered nosave memory: 000000007deb1000 - 000000007dfba000
PM: Registered nosave memory: 000000007dfba000 - 000000007e1d4000
PM: Registered nosave memory: 000000007e1d4000 - 000000007f381000
PM: Registered nosave memory: 000000007f381000 - 000000007f800000
PM: Registered nosave memory: 000000007f800000 - 0000000080000000
PM: Registered nosave memory: 0000000080000000 - 0000000090000000
PM: Registered nosave memory: 0000000090000000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed40000
PM: Registered nosave memory: 00000000fed40000 - 00000000ff000000
PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at 90000000 (gap: 90000000:6ed1c000)
Booting paravirtualized kernel on bare hardware
NR_CPUS:4096 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 31 pages/cpu @ffff880028200000 s94552 r8192 d24232 u524288
pcpu-alloc: s94552 r8192 d24232 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 12394896
Policy zone: Normal
PID hash table entries: 4096 (order: 3, 32768 bytes)
xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
Checking aperture...
No AGP bridge found
dmar: Queued invalidation will be enabled to support x2apic and Intr-remapping.
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
Memory: 49375580k/52428800k available (5223k kernel code, 2131988k absent, 921232k reserved, 7119k data, 1264k init)
Hierarchical RCU implementation.
NR_IRQS:33024 nr_irqs:848
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
allocated 201326592 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2500.147 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 5000.29 BogoMIPS (lpj=2500147)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes)
Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
Initializing cgroup subsys net_prio
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 21 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20090903
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 21439 entries in 85 pages
dmar: Host address width 46
dmar: DRHD base: 0x000000fbffc000 flags: 0x1
dmar: IOMMU 0: reg_base_addr fbffc000 ver 1:0 cap d2078c106f0466 ecap f020de
dmar: RMRR base: 0x0000007de87000 end: 0x0000007de93fff
dmar: ATSR flags: 0x0
dmar: RHSA base: 0x000000fbffc000 proximity domain: 0x0
IOAPIC id 0 under DRHD base 0xfbffc000
IOAPIC id 2 under DRHD base 0xfbffc000
HPET id 0 under DRHD base 0xfbffc000
Enabled IRQ remapping in x2apic mode
Enabling x2apic
Enabled x2apic
APIC routing finalized to cluster x2apic.
alloc irq_desc for 48 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
alloc irq_2_iommu on node 0
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Xeon(R) CPU E5-2609 v2 @ 2.50GHz stepping 04
Performance Events: PEBS fmt1+, generic architected perfmon, Intel PMU driver.
... version: 3
... bit width: 48
... generic registers: 8
... value mask: 0000ffffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 00000007000000ff
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1 #2 #3 Ok.
Brought up 4 CPUs
Total of 4 processors activated (20001.17 BogoMIPS).
sizeof(vma)=200 bytes
sizeof(page)=56 bytes
sizeof(inode)=592 bytes
sizeof(dentry)=192 bytes
sizeof(ext3inode)=800 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=232 bytes
sizeof(task_struct)=2648 bytes
devtmpfs: initialized
PM: Registering ACPI NVS region at 7dfba000 (2203648 bytes)
PM: Registering ACPI NVS region at 7f381000 (4714496 bytes)
regulator: core version 0.5
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base 80000000 segment 0 buses 0 - 255
PCI: MCFG area at 80000000 reserved in E820
PCI: Using MMCONFIG at 80000000 - 8fffffff
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: EC: Look up EC in DSDT
_OSC request data:1 17
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Dynamic OEM Table Load - [PRAD] OemId [PRADID] OemTableId [PRADTID]
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
HEST: Table parsing has been initialized.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x03af]
pci_root PNP0A08:00: host bridge window [io 0x03e0-0x0cf7]
pci_root PNP0A08:00: host bridge window [io 0x03b0-0x03df]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff]
pci_root PNP0A08:00: host bridge window [mem 0xfed08000-0xfed08fff]
pci_root PNP0A08:00: host bridge window [mem 0xfed0e000-0xfed0ffff]
pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfbffffff]
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:01.1: PME# supported from D0 D3hot D3cold
pci 0000:00:01.1: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: reg 10: [mem 0xfb11c000-0xfb11ffff 64bit]
pci 0000:00:04.1: reg 10: [mem 0xfb118000-0xfb11bfff 64bit]
pci 0000:00:04.2: reg 10: [mem 0xfb114000-0xfb117fff 64bit]
pci 0000:00:04.3: reg 10: [mem 0xfb110000-0xfb113fff 64bit]
pci 0000:00:04.4: reg 10: [mem 0xfb10c000-0xfb10ffff 64bit]
pci 0000:00:04.5: reg 10: [mem 0xfb108000-0xfb10bfff 64bit]
pci 0000:00:04.6: reg 10: [mem 0xfb104000-0xfb107fff 64bit]
pci 0000:00:04.7: reg 10: [mem 0xfb100000-0xfb103fff 64bit]
pci 0000:00:05.4: reg 10: [mem 0xfb125000-0xfb125fff]
pci 0000:00:11.0: PME# supported from D0 D3hot D3cold
pci 0000:00:11.0: PME# disabled
pci 0000:00:16.0: reg 10: [mem 0xfed0e000-0xfed0e00f 64bit]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:16.0: PME# disabled
pci 0000:00:16.1: reg 10: [mem 0xfed0f000-0xfed0f00f 64bit]
pci 0000:00:16.1: PME# supported from D0 D3hot D3cold
pci 0000:00:16.1: PME# disabled
pci 0000:00:1a.0: reg 10: [mem 0xfb123000-0xfb1233ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.0: reg 10: [mem 0xfb122000-0xfb1223ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10: [io 0xf050-0xf057]
pci 0000:00:1f.2: reg 14: [io 0xf040-0xf043]
pci 0000:00:1f.2: reg 18: [io 0xf030-0xf037]
pci 0000:00:1f.2: reg 1c: [io 0xf020-0xf023]
pci 0000:00:1f.2: reg 20: [io 0xf000-0xf01f]
pci 0000:00:1f.2: reg 24: [mem 0xfb121000-0xfb1217ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10: [mem 0xfb120000-0xfb1200ff 64bit]
pci 0000:00:1f.3: reg 20: [io 0x1180-0x119f]
pci 0000:00:1f.6: reg 10: [mem 0xfed08000-0xfed08fff 64bit]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:02:00.0: reg 10: [mem 0xf9680000-0xf96fffff 64bit pref]
pci 0000:02:00.0: reg 18: [io 0xe020-0xe03f]
pci 0000:02:00.0: reg 20: [mem 0xf9b04000-0xf9b07fff 64bit pref]
pci 0000:02:00.0: reg 30: [mem 0xfbe80000-0xfbefffff pref]
pci 0000:02:00.0: PME# supported from D0 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.0: reg 190: [mem 0xf9900000-0xf9903fff 64bit pref]
pci 0000:02:00.1: reg 10: [mem 0xf9600000-0xf967ffff 64bit pref]
pci 0000:02:00.1: reg 18: [io 0xe000-0xe01f]
pci 0000:02:00.1: reg 20: [mem 0xf9b00000-0xf9b03fff 64bit pref]
pci 0000:02:00.1: reg 30: [mem 0xfbe00000-0xfbe7ffff pref]
pci 0000:02:00.1: PME# supported from D0 D3hot
pci 0000:02:00.1: PME# disabled
pci 0000:02:00.1: reg 184: [mem 0xf9800000-0xf9803fff 64bit pref]
pci 0000:02:00.1: reg 190: [mem 0xf9700000-0xf9703fff 64bit pref]
pci 0000:00:01.1: PCI bridge to [bus 02-03]
pci 0000:00:01.1: bridge window [io 0xe000-0xefff]
pci 0000:00:01.1: bridge window [mem 0xfbe00000-0xfbefffff]
pci 0000:00:01.1: bridge window [mem 0xf9600000-0xf9bfffff 64bit pref]
pci 0000:04:00.0: reg 10: [mem 0xfba20000-0xfba3ffff]
pci 0000:04:00.0: reg 14: [mem 0xfb800000-0xfb9fffff]
pci 0000:04:00.0: reg 18: [io 0xd020-0xd03f]
pci 0000:04:00.0: reg 1c: [mem 0xfba44000-0xfba47fff]
pci 0000:04:00.0: reg 30: [mem 0xfb600000-0xfb7fffff pref]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:04:00.1: reg 10: [mem 0xfba00000-0xfba1ffff]
pci 0000:04:00.1: reg 14: [mem 0xfb400000-0xfb5fffff]
pci 0000:04:00.1: reg 18: [io 0xd000-0xd01f]
pci 0000:04:00.1: reg 1c: [mem 0xfba40000-0xfba43fff]
pci 0000:04:00.1: reg 30: [mem 0xfb200000-0xfb3fffff pref]
pci 0000:04:00.1: PME# supported from D0 D3hot D3cold
pci 0000:04:00.1: PME# disabled
pci 0000:00:02.0: PCI bridge to [bus 04-04]
pci 0000:00:02.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:02.0: bridge window [mem 0xfb200000-0xfbafffff]
pci 0000:00:02.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:05:00.0: reg 10: [io 0xc000-0xc0ff]
pci 0000:05:00.0: reg 14: [mem 0xfbd60000-0xfbd63fff 64bit]
pci 0000:05:00.0: reg 1c: [mem 0xfbd00000-0xfbd3ffff 64bit]
pci 0000:05:00.0: reg 30: [mem 0xfbd40000-0xfbd5ffff pref]
pci 0000:05:00.0: supports D1 D2
pci 0000:00:03.0: PCI bridge to [bus 05-05]
pci 0000:00:03.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:03.0: bridge window [mem 0xfbd00000-0xfbdfffff]
pci 0000:00:03.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:06:00.0: reg 10: [mem 0xf947c000-0xf947ffff 64bit pref]
pci 0000:06:00.0: reg 18: [mem 0xf9000000-0xf93fffff 64bit pref]
pci 0000:06:00.0: reg 20: [io 0xb000-0xb0ff]
pci 0000:06:00.0: reg 164: [mem 0xf9400000-0xf9403fff 64bit pref]
pci 0000:00:11.0: PCI bridge to [bus 06-06]
pci 0000:00:11.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:11.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:11.0: bridge window [mem 0xf9000000-0xf94fffff 64bit pref]
pci 0000:07:00.0: reg 10: [mem 0xfbc60000-0xfbc7ffff]
pci 0000:07:00.0: reg 18: [io 0xa060-0xa07f]
pci 0000:07:00.0: reg 1c: [mem 0xfbc8c000-0xfbc8ffff]
pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 10: [mem 0xfbc40000-0xfbc5ffff]
pci 0000:07:00.1: reg 18: [io 0xa040-0xa05f]
pci 0000:07:00.1: reg 1c: [mem 0xfbc88000-0xfbc8bfff]
pci 0000:07:00.1: PME# supported from D0 D3hot D3cold
pci 0000:07:00.1: PME# disabled
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.2: reg 10: [mem 0xfbc20000-0xfbc3ffff]
pci 0000:07:00.2: reg 18: [io 0xa020-0xa03f]
pci 0000:07:00.2: reg 1c: [mem 0xfbc84000-0xfbc87fff]
pci 0000:07:00.2: PME# supported from D0 D3hot D3cold
pci 0000:07:00.2: PME# disabled
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.2: reg 190: [mem 0xf9c40000-0xf9c43fff 64bit pref]
pci 0000:07:00.3: reg 10: [mem 0xfbc00000-0xfbc1ffff]
pci 0000:07:00.3: reg 18: [io 0xa000-0xa01f]
pci 0000:07:00.3: reg 1c: [mem 0xfbc80000-0xfbc83fff]
pci 0000:07:00.3: PME# supported from D0 D3hot D3cold
pci 0000:07:00.3: PME# disabled
pci 0000:07:00.3: reg 184: [mem 0xf9c20000-0xf9c23fff 64bit pref]
pci 0000:07:00.3: reg 190: [mem 0xf9c00000-0xf9c03fff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 07-08]
pci 0000:00:1c.0: bridge window [io 0xa000-0xafff]
pci 0000:00:1c.0: bridge window [mem 0xfbc00000-0xfbcfffff]
pci 0000:00:1c.0: bridge window [mem 0xf9c00000-0xf9cfffff 64bit pref]
pci 0000:09:01.0: reg 10: [mem 0xf8000000-0xf8ffffff pref]
pci 0000:09:01.0: reg 14: [mem 0xfb000000-0xfb003fff]
pci 0000:09:01.0: reg 18: [mem 0xfa800000-0xfaffffff]
pci 0000:00:1e.0: PCI bridge to [bus 09-09] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xfa800000-0xfb0fffff]
pci 0000:00:1e.0: bridge window [mem 0xf8000000-0xf8ffffff 64bit pref]
pci 0000:00:1e.0: bridge window [io 0x0000-0x03af] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x03e0-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x03b0-0x03df] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xfed08000-0xfed08fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xfed0e000-0xfed0ffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfbffffff] (subtractive decode)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT]
pci0000:00: Requesting ACPI _OSC control (0x1d)
pci0000:00: ACPI _OSC control (0x11) granted
ACPI: PCI Root Bridge [UNC0] (domain 0000 [bus ff])
pci0000:ff: Requesting ACPI _OSC control (0x1d)
pci0000:ff: ACPI _OSC control (0x1d) granted
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
vgaarb: device added: PCI:0000:09:01.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:09:01.0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: old code would have set cacheline size to 32 bytes, but clflush_size = 64
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
alloc irq_desc for 49 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
alloc irq_desc for 50 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
alloc irq_desc for 51 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
alloc irq_desc for 52 on node 0
alloc kstat_irqs on node 0
alloc irq_2_iommu on node 0
HPET: 8 timers in total, 4 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 49, 50, 51, 52, 0, 0
hpet0: 8 comparators, 64-bit 14.318180 MHz counter
hpet: hpet2 irq 49 for MSI
hpet: hpet3 irq 50 for MSI
hpet: hpet4 irq 51 for MSI
hpet: hpet5 irq 52 for MSI
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [mem 0xfc000000-0xfcffffff]
pnp 00:01: [mem 0xfd000000-0xfdffffff]
pnp 00:01: [mem 0xfe000000-0xfeafffff]
pnp 00:01: [mem 0xfeb00000-0xfebfffff]
pnp 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:02: [mem 0xfbffc000-0xfbffdfff]
pnp 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:03: [dma 4]
pnp 00:03: [io 0x0000-0x000f]
pnp 00:03: [io 0x0081-0x0083]
pnp 00:03: [io 0x0087]
pnp 00:03: [io 0x0089-0x008b]
pnp 00:03: [io 0x008f]
pnp 00:03: [io 0x00c0-0x00df]
pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:04: [io 0x0070-0x0071]
pnp 00:04: [irq 8]
pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:05: [io 0x0061]
pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:06: [io 0x0010-0x001f]
pnp 00:06: [io 0x0022-0x003f]
pnp 00:06: [io 0x0044-0x005f]
pnp 00:06: [io 0x0062-0x0063]
pnp 00:06: [io 0x0065-0x006f]
pnp 00:06: [io 0x0072-0x007f]
pnp 00:06: [io 0x0080]
pnp 00:06: [io 0x0084-0x0086]
pnp 00:06: [io 0x0088]
pnp 00:06: [io 0x008c-0x008e]
pnp 00:06: [io 0x0090-0x009f]
pnp 00:06: [io 0x00a2-0x00bf]
pnp 00:06: [io 0x00e0-0x00ef]
pnp 00:06: [io 0x04d0-0x04d1]
pnp 00:06: [mem 0x00000400-0x000004ff]
pnp 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:07: [io 0x00f0-0x00ff]
pnp 00:07: [irq 13]
pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:09: [io 0x0b00-0x0b7f]
pnp 00:09: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:09: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:09: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0a: [io 0x03f8-0x03ff]
pnp 00:0a: [irq 4]
pnp 00:0a: [dma 0 disabled]
pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0b: [io 0x02f8-0x02ff]
pnp 00:0b: [irq 3]
pnp 00:0b: [dma 0 disabled]
pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0c: [io 0x0ca2]
pnp 00:0c: [io 0x0ca3]
pnp 00:0c: Plug and Play ACPI device, IDs IPI0001 (active)
pnp 00:0d: [io 0x0400-0x0453]
pnp 00:0d: [io 0x0458-0x047f]
pnp 00:0d: [io 0x1180-0x119f]
pnp 00:0d: [io 0x0500-0x057f]
pnp 00:0d: [mem 0xfed1c000-0xfed1ffff]
pnp 00:0d: [mem 0xfec00000-0xfecfffff]
pnp 00:0d: [mem 0xff000000-0xffffffff]
pnp 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:0e: [io 0x0454-0x0457]
pnp 00:0e: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
pnp 00:0f: [mem 0xfed00000-0xfed003ff]
pnp 00:0f: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:10: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:11: [mem 0x00000000-0x0009ffff]
pnp 00:11: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 18 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: [mem 0xfc000000-0xfcffffff] has been reserved
system 00:01: [mem 0xfd000000-0xfdffffff] has been reserved
system 00:01: [mem 0xfe000000-0xfeafffff] has been reserved
system 00:01: [mem 0xfeb00000-0xfebfffff] has been reserved
system 00:02: [mem 0xfbffc000-0xfbffdfff] could not be reserved
system 00:06: [io 0x04d0-0x04d1] has been reserved
system 00:06: [mem 0x00000400-0x000004ff] could not be reserved
system 00:09: [io 0x0b00-0x0b7f] has been reserved
system 00:0d: [io 0x0400-0x0453] has been reserved
system 00:0d: [io 0x0458-0x047f] has been reserved
system 00:0d: [io 0x1180-0x119f] has been reserved
system 00:0d: [io 0x0500-0x057f] has been reserved
system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:0d: [mem 0xfec00000-0xfecfffff] could not be reserved
system 00:0d: [mem 0xff000000-0xffffffff] has been reserved
system 00:0e: [io 0x0454-0x0457] has been reserved
system 00:11: [mem 0x00000000-0x0009ffff] could not be reserved
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:06:00.0: reg 164: [mem 0xf9400000-0xf9403fff 64bit pref]
pci 0000:00:11.0: BAR 14: assigned [mem 0x90000000-0x900fffff]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io disabled]
pci 0000:00:01.0: bridge window [mem disabled]
pci 0000:00:01.0: bridge window [mem pref disabled]
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.0: reg 190: [mem 0xf9900000-0xf9903fff 64bit pref]
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.1: reg 184: [mem 0xf9800000-0xf9803fff 64bit pref]
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.0: reg 190: [mem 0xf9900000-0xf9903fff 64bit pref]
pci 0000:02:00.1: reg 190: [mem 0xf9700000-0xf9703fff 64bit pref]
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.0: reg 190: [mem 0xf9900000-0xf9903fff 64bit pref]
pci 0000:02:00.1: reg 184: [mem 0xf9800000-0xf9803fff 64bit pref]
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.0: reg 184: [mem 0xf9a00000-0xf9a03fff 64bit pref]
pci 0000:02:00.0: BAR 7: assigned [mem 0xf9700000-0xf97fffff 64bit pref]
pci 0000:02:00.0: BAR 7: set to [mem 0xf9700000-0xf97fffff 64bit pref] (PCI address [0xf9700000-0xf97fffff]
pci 0000:02:00.0: reg 190: [mem 0xf9900000-0xf9903fff 64bit pref]
pci 0000:02:00.0: reg 190: [mem 0xf9900000-0xf9903fff 64bit pref]
pci 0000:02:00.0: BAR 10: assigned [mem 0xf9800000-0xf98fffff 64bit pref]
pci 0000:02:00.0: BAR 10: set to [mem 0xf9800000-0xf98fffff 64bit pref] (PCI address [0xf9800000-0xf98fffff]
pci 0000:02:00.1: reg 184: [mem 0xf9800000-0xf9803fff 64bit pref]
pci 0000:02:00.1: reg 184: [mem 0xf9800000-0xf9803fff 64bit pref]
pci 0000:02:00.1: BAR 7: assigned [mem 0xf9900000-0xf99fffff 64bit pref]
pci 0000:02:00.1: BAR 7: set to [mem 0xf9900000-0xf99fffff 64bit pref] (PCI address [0xf9900000-0xf99fffff]
pci 0000:02:00.1: reg 190: [mem 0xf9700000-0xf9703fff 64bit pref]
pci 0000:02:00.1: reg 190: [mem 0xf9700000-0xf9703fff 64bit pref]
pci 0000:02:00.1: BAR 10: assigned [mem 0xf9a00000-0xf9afffff 64bit pref]
pci 0000:02:00.1: BAR 10: set to [mem 0xf9a00000-0xf9afffff 64bit pref] (PCI address [0xf9a00000-0xf9afffff]
pci 0000:00:01.1: PCI bridge to [bus 02-03]
pci 0000:00:01.1: PCI bridge to [bus 02-03]
pci 0000:00:01.1: bridge window [io 0xe000-0xefff]
pci 0000:00:01.1: bridge window [mem 0xfbe00000-0xfbefffff]
pci 0000:00:01.1: bridge window [mem 0xf9600000-0xf9bfffff 64bit pref]
pci 0000:00:02.0: PCI bridge to [bus 04-04]
pci 0000:00:02.0: PCI bridge to [bus 04-04]
pci 0000:00:02.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:02.0: bridge window [mem 0xfb200000-0xfbafffff]
pci 0000:00:02.0: bridge window [mem pref disabled]
pci 0000:00:03.0: PCI bridge to [bus 05-05]
pci 0000:00:03.0: PCI bridge to [bus 05-05]
pci 0000:00:03.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:03.0: bridge window [mem 0xfbd00000-0xfbdfffff]
pci 0000:00:03.0: bridge window [mem pref disabled]
pci 0000:06:00.0: reg 164: [mem 0xf9400000-0xf9403fff 64bit pref]
pci 0000:06:00.0: reg 164: [mem 0xf9400000-0xf9403fff 64bit pref]
pci 0000:06:00.0: reg 164: [mem 0xf9400000-0xf9403fff 64bit pref]
pci 0000:06:00.0: BAR 7: assigned [mem 0xf9400000-0xf947bfff 64bit pref]
pci 0000:06:00.0: BAR 7: set to [mem 0xf9400000-0xf947bfff 64bit pref] (PCI address [0xf9400000-0xf947bfff]
pci 0000:00:11.0: PCI bridge to [bus 06-06]
pci 0000:00:11.0: PCI bridge to [bus 06-06]
pci 0000:00:11.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:11.0: bridge window [mem 0x90000000-0x900fffff]
pci 0000:00:11.0: bridge window [mem 0xf9000000-0xf94fffff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.2: reg 190: [mem 0xf9c40000-0xf9c43fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.3: reg 184: [mem 0xf9c20000-0xf9c23fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.2: reg 190: [mem 0xf9c40000-0xf9c43fff 64bit pref]
pci 0000:07:00.3: reg 190: [mem 0xf9c00000-0xf9c03fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.2: reg 190: [mem 0xf9c40000-0xf9c43fff 64bit pref]
pci 0000:07:00.3: reg 184: [mem 0xf9c20000-0xf9c23fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: reg 184: [mem 0xf9ce0000-0xf9ce3fff 64bit pref]
pci 0000:07:00.0: BAR 7: assigned [mem 0xf9c00000-0xf9c1ffff 64bit pref]
pci 0000:07:00.0: BAR 7: set to [mem 0xf9c00000-0xf9c1ffff 64bit pref] (PCI address [0xf9c00000-0xf9c1ffff]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.0: reg 190: [mem 0xf9cc0000-0xf9cc3fff 64bit pref]
pci 0000:07:00.0: BAR 10: assigned [mem 0xf9c20000-0xf9c3ffff 64bit pref]
pci 0000:07:00.0: BAR 10: set to [mem 0xf9c20000-0xf9c3ffff 64bit pref] (PCI address [0xf9c20000-0xf9c3ffff]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: reg 184: [mem 0xf9ca0000-0xf9ca3fff 64bit pref]
pci 0000:07:00.1: BAR 7: assigned [mem 0xf9c40000-0xf9c5ffff 64bit pref]
pci 0000:07:00.1: BAR 7: set to [mem 0xf9c40000-0xf9c5ffff 64bit pref] (PCI address [0xf9c40000-0xf9c5ffff]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.1: reg 190: [mem 0xf9c80000-0xf9c83fff 64bit pref]
pci 0000:07:00.1: BAR 10: assigned [mem 0xf9c60000-0xf9c7ffff 64bit pref]
pci 0000:07:00.1: BAR 10: set to [mem 0xf9c60000-0xf9c7ffff 64bit pref] (PCI address [0xf9c60000-0xf9c7ffff]
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.2: reg 184: [mem 0xf9c60000-0xf9c63fff 64bit pref]
pci 0000:07:00.2: BAR 7: assigned [mem 0xf9c80000-0xf9c9ffff 64bit pref]
pci 0000:07:00.2: BAR 7: set to [mem 0xf9c80000-0xf9c9ffff 64bit pref] (PCI address [0xf9c80000-0xf9c9ffff]
pci 0000:07:00.2: reg 190: [mem 0xf9c40000-0xf9c43fff 64bit pref]
pci 0000:07:00.2: reg 190: [mem 0xf9c40000-0xf9c43fff 64bit pref]
pci 0000:07:00.2: BAR 10: assigned [mem 0xf9ca0000-0xf9cbffff 64bit pref]
pci 0000:07:00.2: BAR 10: set to [mem 0xf9ca0000-0xf9cbffff 64bit pref] (PCI address [0xf9ca0000-0xf9cbffff]
pci 0000:07:00.3: reg 184: [mem 0xf9c20000-0xf9c23fff 64bit pref]
pci 0000:07:00.3: reg 184: [mem 0xf9c20000-0xf9c23fff 64bit pref]
pci 0000:07:00.3: BAR 7: assigned [mem 0xf9cc0000-0xf9cdffff 64bit pref]
pci 0000:07:00.3: BAR 7: set to [mem 0xf9cc0000-0xf9cdffff 64bit pref] (PCI address [0xf9cc0000-0xf9cdffff]
pci 0000:07:00.3: reg 190: [mem 0xf9c00000-0xf9c03fff 64bit pref]
pci 0000:07:00.3: reg 190: [mem 0xf9c00000-0xf9c03fff 64bit pref]
pci 0000:07:00.3: BAR 10: assigned [mem 0xf9ce0000-0xf9cfffff 64bit pref]
pci 0000:07:00.3: BAR 10: set to [mem 0xf9ce0000-0xf9cfffff 64bit pref] (PCI address [0xf9ce0000-0xf9cfffff]
pci 0000:00:1c.0: PCI bridge to [bus 07-08]
pci 0000:00:1c.0: PCI bridge to [bus 07-08]
pci 0000:00:1c.0: bridge window [io 0xa000-0xafff]
pci 0000:00:1c.0: bridge window [mem 0xfbc00000-0xfbcfffff]
pci 0000:00:1c.0: bridge window [mem 0xf9c00000-0xf9cfffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 09-09]
pci 0000:00:1e.0: PCI bridge to [bus 09-09]
pci 0000:00:1e.0: bridge window [io disabled]
pci 0000:00:1e.0: bridge window [mem 0xfa800000-0xfb0fffff]
pci 0000:00:1e.0: bridge window [mem 0xf8000000-0xf8ffffff 64bit pref]
alloc irq_desc for 26 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
pci 0000:00:01.0: PCI INT A -> GSI 26 (level, low) -> IRQ 26
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:01.1: PCI INT A -> GSI 26 (level, low) -> IRQ 26
pci 0000:00:01.1: setting latency timer to 64
alloc irq_desc for 33 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
pci 0000:00:02.0: PCI INT A -> GSI 33 (level, low) -> IRQ 33
pci 0000:00:02.0: setting latency timer to 64
alloc irq_desc for 41 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
pci 0000:00:03.0: PCI INT A -> GSI 41 (level, low) -> IRQ 41
pci 0000:00:03.0: setting latency timer to 64
alloc irq_desc for 16 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
pci 0000:00:11.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:11.0: setting latency timer to 64
alloc irq_desc for 17 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x03af]
pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7]
pci_bus 0000:00: resource 6 [io 0x03b0-0x03df]
pci_bus 0000:00: resource 7 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
pci_bus 0000:00: resource 10 [mem 0xfed08000-0xfed08fff]
pci_bus 0000:00: resource 11 [mem 0xfed0e000-0xfed0ffff]
pci_bus 0000:00: resource 12 [mem 0x80000000-0xfbffffff]
pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
pci_bus 0000:02: resource 1 [mem 0xfbe00000-0xfbefffff]
pci_bus 0000:02: resource 2 [mem 0xf9600000-0xf9bfffff 64bit pref]
pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:04: resource 1 [mem 0xfb200000-0xfbafffff]
pci_bus 0000:05: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:05: resource 1 [mem 0xfbd00000-0xfbdfffff]
pci_bus 0000:06: resource 0 [io 0xb000-0xbfff]
pci_bus 0000:06: resource 1 [mem 0x90000000-0x900fffff]
pci_bus 0000:06: resource 2 [mem 0xf9000000-0xf94fffff 64bit pref]
pci_bus 0000:07: resource 0 [io 0xa000-0xafff]
pci_bus 0000:07: resource 1 [mem 0xfbc00000-0xfbcfffff]
pci_bus 0000:07: resource 2 [mem 0xf9c00000-0xf9cfffff 64bit pref]
pci_bus 0000:09: resource 1 [mem 0xfa800000-0xfb0fffff]
pci_bus 0000:09: resource 2 [mem 0xf8000000-0xf8ffffff 64bit pref]
pci_bus 0000:09: resource 4 [io 0x0000-0x03af]
pci_bus 0000:09: resource 5 [io 0x03e0-0x0cf7]
pci_bus 0000:09: resource 6 [io 0x03b0-0x03df]
pci_bus 0000:09: resource 7 [io 0x0d00-0xffff]
pci_bus 0000:09: resource 8 [mem 0x000a0000-0x000bffff]
pci_bus 0000:09: resource 9 [mem 0x000c0000-0x000dffff]
pci_bus 0000:09: resource 10 [mem 0xfed08000-0xfed08fff]
pci_bus 0000:09: resource 11 [mem 0xfed0e000-0xfed0ffff]
pci_bus 0000:09: resource 12 [mem 0x80000000-0xfbffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1a.0: PCI INT A disabled
alloc irq_desc for 23 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1d.0: PCI INT A disabled
pci 0000:04:00.0: Disabling L0s
pci 0000:04:00.1: Disabling L0s
pci 0000:09:01.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 14362k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1382967210.653:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 32768
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
ksign: Installing public key data
Loading keyring
- Added public key 11EE41BC87D92128
- User ID: CentOS (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
intel_idle: MWAIT substates: 0x1120
intel_idle: v0.4 model 0x3E
intel_idle: lapic_timer_reliable_states 0xffffffff
ipmi message handler version 39.2
IPMI System Interface driver.
ipmi_si: Adding ACPI-specified kcs state machine
ipmi_si: Adding SMBIOS-specified kcs state machine: duplicate interface
ipmi_si: Adding ACPI-specified kcs state machine: duplicate interface
ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
ipmi: Found new BMC (man_id: 0x002a7c, prod_id: 0x0626, dev_id: 0x20)
IPMI kcs interface initialized
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
ACPI: acpi_idle yielding to intel_idle
ERST: Error Record Serialization Table (ERST) support is initialized.
GHES: APEI firmware first mode is enabled by WHEA _OSC.
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
crash memory driver: version 1.1
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.0: irq 16, io mem 0xfb123000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32-358.23.2.el6.x86_64 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xfb122000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32-358.23.2.el6.x86_64 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
PNP: No PS/2 controller found. Probing ports directly.
mice: PS/2 mouse device common for all mice
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
registered taskstats version 1
rtc_cmos 00:04: setting system clock to 2013-10-28 13:33:31 UTC (1382967211)
Initalizing network drop monitor service
Freeing unused kernel memory: 1264k freed
Write protecting the kernel read-only data: 10240k
Freeing unused kernel memory: 900k freed
Freeing unused kernel memory: 1672k freed
dracut: dracut-004-303.el6
dracut: rd_NO_LUKS: removing cryptoluks activation
dracut: rd_NO_LVM: removing LVM activation
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.23.6-ioctl (2012-07-25) initialised: dm-devel@redhat.com
udev: starting version 147
dracut: Starting plymouth daemon
ahci 0000:00:1f.2: version 3.0
alloc irq_desc for 18 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ahci 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
alloc irq_desc for 53 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ahci 0000:00:1f.2: irq 53 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfb121000 port 0xfb121100 irq 53
ata2: SATA max UDMA/133 abar m2048@0xfb121000 port 0xfb121180 irq 53
ata3: SATA max UDMA/133 abar m2048@0xfb121000 port 0xfb121200 irq 53
ata4: SATA max UDMA/133 abar m2048@0xfb121000 port 0xfb121280 irq 53
ata5: SATA max UDMA/133 abar m2048@0xfb121000 port 0xfb121300 irq 53
ata6: SATA max UDMA/133 abar m2048@0xfb121000 port 0xfb121380 irq 53
usb 1-1: new high speed USB device number 2 using ehci_hcd
usb 1-1: New USB device found, idVendor=8087, idProduct=0024
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
Refined TSC clocksource calibration: 2499.999 MHz.
Switching to clocksource tsc
ata3: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: ATA-8: ST9250610NS, SN03, max UDMA/133
ata1.00: ATA-8: ST9250610NS, SN03, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST9250610NS SN03 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access ATA ST9250610NS SN03 PQ: 0 ANSI: 5
ACPI: WMI: Mapper loaded
usb 2-1: new high speed USB device number 2 using ehci_hcd
megasas: 06.504.01.00-rh1 Mon. Oct. 8 17:00:00 PDT 2012
megasas: 0x1000:0x0079:0x15d9:0x0700: bus 5:slot 0:func 0
alloc irq_desc for 40 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
megaraid_sas 0000:05:00.0: PCI INT A -> GSI 40 (level, low) -> IRQ 40
megaraid_sas 0000:05:00.0: setting latency timer to 64
megasas: FW now in Ready state
alloc irq_desc for 54 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
megaraid_sas 0000:05:00.0: irq 54 for MSI/MSI-X
megasas_init_mfi: fw_support_ieee=0
megasas: INIT adapter done
usb 2-1: New USB device found, idVendor=8087, idProduct=0024
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
scsi6 : LSI SAS based MegaRAID driver
scsi 6:0:2:0: Direct-Access ATA ST31000524NS SN12 PQ: 0 ANSI: 5
scsi 6:0:3:0: Direct-Access ATA ST31000520AS CC32 PQ: 0 ANSI: 5
scsi 6:0:6:0: Direct-Access ATA WDC WD1001FALS-0 1D05 PQ: 0 ANSI: 5
scsi 6:0:7:0: Direct-Access ATA WDC WD1001FALS-0 1D05 PQ: 0 ANSI: 5
scsi 6:0:10:0: Direct-Access ATA WDC WD1001FALS-0 1D05 PQ: 0 ANSI: 5
scsi 6:0:11:0: Direct-Access ATA WDC WD30EFRX-68A 0A80 PQ: 0 ANSI: 5
scsi 6:0:15:0: Direct-Access ATA WDC WD30EFRX-68A 0A80 PQ: 0 ANSI: 5
scsi 6:0:16:0: Enclosure LSI CORP SAS2X28 0717 PQ: 0 ANSI: 5
scsi 6:0:19:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:0:20:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:0:21:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:0:22:0: Direct-Access SEAGATE ST3000NM0023 0003 PQ: 0 ANSI: 6
scsi 6:0:23:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:0:24:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:0:25:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:0:26:0: Direct-Access SEAGATE ST3000NM0023 A001 PQ: 0 ANSI: 6
scsi 6:2:0:0: Direct-Access SMC SMC2108 2.13 PQ: 0 ANSI: 5
scsi 6:2:1:0: Direct-Access SMC SMC2108 2.13 PQ: 0 ANSI: 5
usb 1-1.3: new full speed USB device number 3 using ehci_hcd
isci: Intel(R) C600 SAS Controller Driver - version 1.1.0-rh
isci 0000:06:00.0: driver configured for rev: 6 silicon
isci 0000:06:00.0: firmware: requesting isci/isci_firmware.bin
isci 0000:06:00.0: OEM SAS parameters (version: 1.0) loaded (firmware)
isci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
isci 0000:06:00.0: setting latency timer to 64
isci 0000:06:00.0: SCU controller 0: phy 3-0 cables: {short, short, short, short}
scsi7 : isci
alloc irq_desc for 55 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
isci 0000:06:00.0: irq 55 for MSI/MSI-X
alloc irq_desc for 56 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
isci 0000:06:00.0: irq 56 for MSI/MSI-X
usb 1-1.3: New USB device found, idVendor=0557, idProduct=2221
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.3: Product: Hermon USB hidmouse Device
usb 1-1.3: Manufacturer: Winbond Electronics Corp
usb 1-1.3: configuration #1 chosen from 1 choice
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input3
generic-usb 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.3/input0
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/input/input4
generic-usb 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.3/input1
usb 2-1.2: new low speed USB device number 3 using ehci_hcd
usb 2-1.2: New USB device found, idVendor=04b3, idProduct=3025
usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1.2: Product: USB NetVista Full Width Keyboard.
usb 2-1.2: Manufacturer: LITE-ON Technology
usb 2-1.2: configuration #1 chosen from 1 choice
input: LITE-ON Technology USB NetVista Full Width Keyboard. as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input5
generic-usb 0003:04B3:3025.0003: input,hidraw2: USB HID v1.10 Keyboard [LITE-ON Technology USB NetVista Full Width Keyboard.] on usb-0000:00:1d.0-1.2/input0
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 6:2:0:0: [sdc] 7804682240 512-byte logical blocks: (3.99 TB/3.63 TiB)
sd 6:2:0:0: [sdc] 4096-byte physical blocks
sd 6:2:1:0: [sdd] 52734357504 512-byte logical blocks: (26.9 TB/24.5 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 6:2:1:0: [sdd] 4096-byte physical blocks
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:2:0:0: [sdc] Write Protect is off
sd 6:2:0:0: [sdc] Mode Sense: 1f 00 00 08
sd 6:2:1:0: [sdd] Write Protect is off
sd 6:2:1:0: [sdd] Mode Sense: 1f 00 00 08
sd 6:2:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
sd 6:2:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sdd:
sdc: sdb1 sdb2 sdb3
sda1 sda2 sda3
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 0:0:0:0: [sda] Attached SCSI disk
sdd1
sd 6:2:1:0: [sdd] Attached SCSI disk
sd 6:2:0:0: [sdc] Attached SCSI disk
md: bind
md: bind
md: raid1 personality registered for level 1
bio: create slab at 1
md/raid1:md0: active with 2 out of 2 mirrors
created bitmap (1 pages) for device md0
md0: bitmap initialized from disk: read 1 pages, set 0 of 657 bits
md0: detected capacity change from 0 to 44040060928
md0: unknown partition table
EXT4-fs (md0): mounted filesystem with ordered data mode. Opts:
dracut: Mounted root filesystem /dev/md0
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
type=1404 audit(1382967213.226:2): selinux=0 auid=4294967295 ses=4294967295
dracut:
dracut: Switching root
udev: starting version 147
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07rh
iTCO_wdt: Found a Patsburg TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
scsi 6:0:16:0: Attached scsi generic sg2 type 13
sd 6:2:0:0: Attached scsi generic sg3 type 0
sd 6:2:1:0: Attached scsi generic sg4 type 0
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
PTP clock support registered
dca service started, version 1.12.1
md: bind
md: bind
md/raid1:md1: active with 2 out of 2 mirrors
created bitmap (2 pages) for device md1
md1: bitmap initialized from disk: read 1 pages, set 0 of 2943 bits
md1: detected capacity change from 0 to 197494964224
md1: unknown partition table
ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.9.15-k
ixgbe: Copyright (c) 1999-2012 Intel Corporation.
alloc irq_desc for 27 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.0: PCI INT A -> GSI 27 (level, low) -> IRQ 27
ixgbe 0000:02:00.0: setting latency timer to 64
alloc irq_desc for 57 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.0: irq 57 for MSI/MSI-X
alloc irq_desc for 58 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.0: irq 58 for MSI/MSI-X
alloc irq_desc for 59 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.0: irq 59 for MSI/MSI-X
alloc irq_desc for 60 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.0: irq 60 for MSI/MSI-X
alloc irq_desc for 61 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.0: irq 61 for MSI/MSI-X
ixgbe 0000:02:00.0: Multiqueue Enabled: Rx Queue count = 4, Tx Queue count = 4
ixgbe 0000:02:00.0: registered PHC device on 0000:02:00.0
ixgbe 0000:02:00.0: (PCI Express:5.0GT/s:Width x4) 00:25:90:c6:c2:94
ixgbe 0000:02:00.0: MAC: 2, PHY: 9, SFP+: 3, PBA No: 400900-000
ixgbe 0000:02:00.0: PCI-Express bandwidth available for this card is not sufficient for optimal performance.
ixgbe 0000:02:00.0: For optimal performance a x8 PCI-Express slot is required.
ixgbe 0000:02:00.0: Intel(R) 10 Gigabit Network Connection
alloc irq_desc for 30 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.1: PCI INT B -> GSI 30 (level, low) -> IRQ 30
ixgbe 0000:02:00.1: setting latency timer to 64
alloc irq_desc for 62 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.1: irq 62 for MSI/MSI-X
alloc irq_desc for 63 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.1: irq 63 for MSI/MSI-X
alloc irq_desc for 64 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.1: irq 64 for MSI/MSI-X
alloc irq_desc for 65 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.1: irq 65 for MSI/MSI-X
alloc irq_desc for 66 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
ixgbe 0000:02:00.1: irq 66 for MSI/MSI-X
ixgbe 0000:02:00.1: Multiqueue Enabled: Rx Queue count = 4, Tx Queue count = 4
ixgbe 0000:02:00.1: registered PHC device on 0000:02:00.1
ixgbe 0000:02:00.1: (PCI Express:5.0GT/s:Width x4) 00:25:90:c6:c2:95
ixgbe 0000:02:00.1: MAC: 2, PHY: 9, SFP+: 4, PBA No: 400900-000
ixgbe 0000:02:00.1: PCI-Express bandwidth available for this card is not sufficient for optimal performance.
ixgbe 0000:02:00.1: For optimal performance a x8 PCI-Express slot is required.
ixgbe 0000:02:00.1: Intel(R) 10 Gigabit Network Connection
igb: Intel(R) Gigabit Ethernet Network Driver - version 4.0.1-k
igb: Copyright (c) 2007-2012 Intel Corporation.
alloc irq_desc for 32 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
igb 0000:04:00.0: setting latency timer to 64
alloc irq_desc for 67 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 67 for MSI/MSI-X
alloc irq_desc for 68 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 68 for MSI/MSI-X
alloc irq_desc for 69 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 69 for MSI/MSI-X
alloc irq_desc for 70 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 70 for MSI/MSI-X
alloc irq_desc for 71 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 71 for MSI/MSI-X
alloc irq_desc for 72 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 72 for MSI/MSI-X
alloc irq_desc for 73 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 73 for MSI/MSI-X
alloc irq_desc for 74 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 74 for MSI/MSI-X
alloc irq_desc for 75 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.0: irq 75 for MSI/MSI-X
igb 0000:04:00.0: Intel(R) Gigabit Ethernet Network Connection
igb 0000:04:00.0: eth2: (PCIe:2.5Gb/s:Width x4) 00:25:90:c4:63:cc
igb 0000:04:00.0: eth2: PBA No: 0101FF-0FF
igb 0000:04:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
alloc irq_desc for 36 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: PCI INT B -> GSI 36 (level, low) -> IRQ 36
igb 0000:04:00.1: setting latency timer to 64
alloc irq_desc for 76 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 76 for MSI/MSI-X
alloc irq_desc for 77 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 77 for MSI/MSI-X
alloc irq_desc for 78 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 78 for MSI/MSI-X
alloc irq_desc for 79 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 79 for MSI/MSI-X
alloc irq_desc for 80 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 80 for MSI/MSI-X
alloc irq_desc for 81 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 81 for MSI/MSI-X
alloc irq_desc for 82 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 82 for MSI/MSI-X
alloc irq_desc for 83 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 83 for MSI/MSI-X
alloc irq_desc for 84 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:04:00.1: irq 84 for MSI/MSI-X
igb 0000:04:00.1: Intel(R) Gigabit Ethernet Network Connection
igb 0000:04:00.1: eth3: (PCIe:2.5Gb/s:Width x4) 00:25:90:c4:63:cd
igb 0000:04:00.1: eth3: PBA No: 0101FF-0FF
igb 0000:04:00.1: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
igb 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
igb 0000:07:00.0: setting latency timer to 64
alloc irq_desc for 85 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 85 for MSI/MSI-X
alloc irq_desc for 86 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 86 for MSI/MSI-X
alloc irq_desc for 87 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 87 for MSI/MSI-X
alloc irq_desc for 88 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 88 for MSI/MSI-X
alloc irq_desc for 89 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 89 for MSI/MSI-X
alloc irq_desc for 90 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 90 for MSI/MSI-X
alloc irq_desc for 91 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 91 for MSI/MSI-X
alloc irq_desc for 92 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 92 for MSI/MSI-X
alloc irq_desc for 93 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.0: irq 93 for MSI/MSI-X
igb 0000:07:00.0: added PHC on eth4
igb 0000:07:00.0: Intel(R) Gigabit Ethernet Network Connection
igb 0000:07:00.0: eth4: (PCIe:5.0Gb/s:Width x4) 00:25:90:86:1a:a2
igb 0000:07:00.0: eth4: PBA No: 105900-000
igb 0000:07:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
igb 0000:07:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
igb 0000:07:00.1: setting latency timer to 64
alloc irq_desc for 94 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 94 for MSI/MSI-X
alloc irq_desc for 95 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 95 for MSI/MSI-X
alloc irq_desc for 96 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 96 for MSI/MSI-X
alloc irq_desc for 97 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 97 for MSI/MSI-X
alloc irq_desc for 98 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 98 for MSI/MSI-X
alloc irq_desc for 99 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 99 for MSI/MSI-X
alloc irq_desc for 100 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 100 for MSI/MSI-X
alloc irq_desc for 101 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 101 for MSI/MSI-X
alloc irq_desc for 102 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.1: irq 102 for MSI/MSI-X
igb 0000:07:00.1: added PHC on eth5
igb 0000:07:00.1: Intel(R) Gigabit Ethernet Network Connection
igb 0000:07:00.1: eth5: (PCIe:5.0Gb/s:Width x4) 00:25:90:86:1a:a3
igb 0000:07:00.1: eth5: PBA No: 105900-000
igb 0000:07:00.1: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
igb 0000:07:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
igb 0000:07:00.2: setting latency timer to 64
alloc irq_desc for 103 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 103 for MSI/MSI-X
alloc irq_desc for 104 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 104 for MSI/MSI-X
alloc irq_desc for 105 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 105 for MSI/MSI-X
alloc irq_desc for 106 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 106 for MSI/MSI-X
alloc irq_desc for 107 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 107 for MSI/MSI-X
alloc irq_desc for 108 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 108 for MSI/MSI-X
alloc irq_desc for 109 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 109 for MSI/MSI-X
alloc irq_desc for 110 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 110 for MSI/MSI-X
alloc irq_desc for 111 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.2: irq 111 for MSI/MSI-X
igb 0000:07:00.2: added PHC on eth6
igb 0000:07:00.2: Intel(R) Gigabit Ethernet Network Connection
igb 0000:07:00.2: eth6: (PCIe:5.0Gb/s:Width x4) 00:25:90:86:1a:a4
igb 0000:07:00.2: eth6: PBA No: 105900-000
igb 0000:07:00.2: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
alloc irq_desc for 19 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
igb 0000:07:00.3: setting latency timer to 64
alloc irq_desc for 112 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 112 for MSI/MSI-X
alloc irq_desc for 113 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 113 for MSI/MSI-X
alloc irq_desc for 114 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 114 for MSI/MSI-X
alloc irq_desc for 115 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 115 for MSI/MSI-X
alloc irq_desc for 116 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 116 for MSI/MSI-X
alloc irq_desc for 117 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 117 for MSI/MSI-X
alloc irq_desc for 118 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 118 for MSI/MSI-X
alloc irq_desc for 119 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 119 for MSI/MSI-X
alloc irq_desc for 120 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
igb 0000:07:00.3: irq 120 for MSI/MSI-X
igb 0000:07:00.3: added PHC on eth7
igb 0000:07:00.3: Intel(R) Gigabit Ethernet Network Connection
igb 0000:07:00.3: eth7: (PCIe:5.0Gb/s:Width x4) 00:25:90:86:1a:a5
igb 0000:07:00.3: eth7: PBA No: 105900-000
igb 0000:07:00.3: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
ses 6:0:16:0: Attached Enclosure device
EXT4-fs (md1): mounted filesystem with ordered data mode. Opts:
Adding 8191992k swap on /dev/sda2. Priority:-1 extents:1 across:8191992k
Adding 8191992k swap on /dev/sdb2. Priority:-2 extents:1 across:8191992k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ipmi device interface
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
netlink: 12 bytes leftover after parsing attributes.
Fusion MPT base driver 3.04.20
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT misc device (ioctl) driver 3.04.20
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
mpt2sas version 13.101.00.00 loaded
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
bonding: Unknown parameter `-o'
bonding: Unknown parameter `-o'
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
bonding: MII link monitoring set to 100 ms
ADDRCONF(NETDEV_UP): bond0: link is not ready
8021q: adding VLAN 0 to HW filter on device bond0
ADDRCONF(NETDEV_UP): bond0: link is not ready
8021q: adding VLAN 0 to HW filter on device bond0
usb 2-1.2: USB disconnect, device number 3
usb 1-1.3: USB disconnect, device number 3
usb 1-1.3: new full speed USB device number 4 using ehci_hcd
usb 1-1.3: New USB device found, idVendor=0557, idProduct=2221
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.3: Product: Hermon USB hidmouse Device
usb 1-1.3: Manufacturer: Winbond Electronics Corp
usb 1-1.3: configuration #1 chosen from 1 choice
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input6
generic-usb 0003:0557:2221.0004: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.3/input0
input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.1/input/input7
generic-usb 0003:0557:2221.0005: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.3/input1
bonding: unable to remove non-existent slave eth0 for bond bond0.
bonding: unable to remove non-existent slave eth1 for bond bond0.
ADDRCONF(NETDEV_UP): bond0: link is not ready
8021q: adding VLAN 0 to HW filter on device bond0
bonding: bond0: Adding slave eth0.
8021q: adding VLAN 0 to HW filter on device eth0
bonding: bond0: enslaving eth0 as a backup interface with a down link.
bonding: bond0: Adding slave eth1.
ixgbe 0000:02:00.0: eth0: detected SFP+: 3
8021q: adding VLAN 0 to HW filter on device eth1
bonding: bond0: enslaving eth1 as a backup interface with a down link.
ADDRCONF(NETDEV_UP): bond0: link is not ready
8021q: adding VLAN 0 to HW filter on device bond0
ixgbe 0000:02:00.1: eth1: detected SFP+: 4
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
bond0: no IPv6 routers present
bonding: bond0: Removing slave eth0
bonding: bond0: Warning: the permanent HWaddr of eth0 - 00:25:90:c6:c2:94 - is still in use by bond0. Set the HWaddr of eth0 to a different address to avoid conflicts.
bonding: bond0: Removing an active aggregator
bonding: bond0: releasing active interface eth0
bonding: bond0: Removing slave eth1
bonding: bond0: Removing an active aggregator
bonding: bond0: releasing active interface eth1
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): bond0: link is not ready
8021q: adding VLAN 0 to HW filter on device bond0
bonding: bond0: Adding slave eth0.
8021q: adding VLAN 0 to HW filter on device eth0
bonding: bond0: enslaving eth0 as a backup interface with a down link.
bonding: bond0: Adding slave eth1.
ixgbe 0000:02:00.0: eth0: detected SFP+: 3
8021q: adding VLAN 0 to HW filter on device eth1
bonding: bond0: enslaving eth1 as a backup interface with a down link.
ADDRCONF(NETDEV_UP): bond0: link is not ready
8021q: adding VLAN 0 to HW filter on device bond0
ixgbe 0000:02:00.1: eth1: detected SFP+: 4
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
bond0: no IPv6 routers present
sdc:
sdc: sdc1
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS (sdc1): Mounting Filesystem
XFS (sdc1): Ending clean mount
Slow work thread pool: Starting up
Slow work thread pool: Ready
FS-Cache: Loaded
Registering the id_resolver key type
FS-Cache: Netfs 'nfs' registered for caching
ixgbe 0000:02:00.1: eth1: NIC Link is Down
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.1: eth1: NIC Link is Down
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.1: eth1: NIC Link is Down
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.1: eth1: NIC Link is Down
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
md: data-check of RAID array md1
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
md: using 128k window, over a total of 192866176k.
md: delaying data-check of md0 until md1 has finished (they share one or more physical units)
md: md1: data-check done.
md: data-check of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
md: using 128k window, over a total of 43007872k.
md: md0: data-check done.
XFS (sdd1): Mounting Filesystem
XFS (sdd1): Ending clean mount
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bonding: bond0: Warning: No 802.3ad response from the link partner for any adapters in the bond
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: changing MTU from 1500 to 9216
ixgbe 0000:02:00.1: eth1: changing MTU from 1500 to 9216
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.0: eth0: detected SFP+: 3
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.1: eth1: detected SFP+: 4
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: NIC Link is Down
ixgbe 0000:02:00.1: eth1: NIC Link is Down
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
ixgbe 0000:02:00.0: eth0: changing MTU from 9216 to 9000
ixgbe 0000:02:00.1: eth1: changing MTU from 9216 to 9000
ixgbe 0000:02:00.0: eth0: detected SFP+: 3
bonding: bond0: link status definitely down for interface eth0, disabling it
ixgbe 0000:02:00.1: eth1: detected SFP+: 4
bonding: bond0: link status definitely down for interface eth1, disabling it
ixgbe 0000:02:00.0: eth0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth0, 10000 Mbps full duplex.
ixgbe 0000:02:00.1: eth1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
bond0: link status definitely up for interface eth1, 10000 Mbps full duplex.
XFS (sdc1): Mounting Filesystem
XFS (sdc1): Ending clean mount