dmesg - goblin
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.2.0-31-generic (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #50-Ubuntu SMP Fri Sep 7 16:16:45 UTC 2012 (Ubuntu 3.2.0-31.50-generic 3.2.28)
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000098000 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000cfda0000 (usable)
BIOS-e820: 00000000cfda0000 - 00000000cfdd1000 (ACPI NVS)
BIOS-e820: 00000000cfdd1000 - 00000000cfe00000 (ACPI data)
BIOS-e820: 00000000cfe00000 - 00000000cff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000022f000000 (usable)
NX (Execute Disable) protection: active
DMI 2.4 present.
DMI: Gigabyte Technology Co., Ltd. GA-A75M-S2V/GA-A75M-S2V, BIOS F5 11/03/2011
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x22f000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-C7FFF write-protect
C8000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 0000000000 mask FF80000000 write-back
1 base 0080000000 mask FFC0000000 write-back
2 base 00C0000000 mask FFF0000000 write-back
3 base 00CFE00000 mask FFFFE00000 uncachable
4 disabled
5 disabled
6 disabled
7 disabled
TOM2: 000000022f000000 aka 8944M
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3GB, range: 256MB, type WB
reg 3, base: 3326MB, range: 2MB, type UC
total RAM covered: 3326M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 4M num_reg: 4 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3GB, range: 256MB, type WB
reg 3, base: 3326MB, range: 2MB, type UC
e820 update range: 00000000cfe00000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xcfda0 max_arch_pfn = 0x400000000
found SMP MP-table at [ffff8800000f5f80] f5f80
initial memory mapped : 0 - 20000000
Base memory trampoline at [ffff880000093000] 93000 size 20480
Using GB pages for direct mapping
init_memory_mapping: 0000000000000000-00000000cfda0000
0000000000 - 00c0000000 page 1G
00c0000000 - 00cfc00000 page 2M
00cfc00000 - 00cfda0000 page 4k
kernel direct mapping tables up to cfda0000 @ 1fffd000-20000000
init_memory_mapping: 0000000100000000-000000022f000000
0100000000 - 0200000000 page 1G
0200000000 - 022f000000 page 2M
kernel direct mapping tables up to 22f000000 @ cfd9e000-cfda0000
RAMDISK: 364d2000 - 37261000
ACPI: RSDP 00000000000f7e30 00014 (v00 GBT )
ACPI: RSDT 00000000cfdd1000 0004C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
ACPI: FACP 00000000cfdd1080 00074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
ACPI: DSDT 00000000cfdd1100 04A26 (v01 GBT GBTUACPI 00001000 MSFT 0100000C)
ACPI: FACS 00000000cfda0000 00040
ACPI: MSDM 00000000cfdd5c00 00055 (v03 GBT GBTUACPI 42302E31 GBTU 01010101)
ACPI: HPET 00000000cfdd5c80 00038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
ACPI: MCFG 00000000cfdd5cc0 0003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
ACPI: EUDS 00000000cfdd5d40 00590 (v01 GBT 00000000 00000000)
ACPI: MATS 00000000cfdd62d0 00034 (v01 GBT 00000000 00000000)
ACPI: APIC 00000000cfdd5b40 000BC (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
ACPI: MATS 00000000cfdd6340 05CD1 (v01 MATS RCM 80000001 INTL 20061109)
ACPI: SSDT 00000000cfddc090 00FD8 (v01 AMD POWERNOW 00000001 AMD 00000001)
ACPI: SSDT 00000000cfddd0e0 00695 (v02 AMD ALIB 00000001 MSFT 04000000)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-000000022f000000
Initmem setup node 0 0000000000000000-000000022f000000
NODE_DATA [000000022effb000 - 000000022effffff]
[ffffea0000000000-ffffea0008bfffff] PMD -> [ffff880226600000-ffff88022e5fffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0022f000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x00000098
0: 0x00000100 -> 0x000cfda0
0: 0x00100000 -> 0x0022f000
On node 0 totalpages: 2092328
DMA zone: 64 pages used for memmap
DMA zone: 5 pages reserved
DMA zone: 3907 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 830944 pages, LIFO batch:31
Normal zone: 19392 pages used for memmap
Normal zone: 1221696 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10b9a201 base: 0xfed00000
SMP: Allowing 8 CPUs, 4 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: 0000000000098000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
PM: Registered nosave memory: 00000000cfda0000 - 00000000cfdd1000
PM: Registered nosave memory: 00000000cfdd1000 - 00000000cfe00000
PM: Registered nosave memory: 00000000cfe00000 - 00000000cff00000
PM: Registered nosave memory: 00000000cff00000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 0000000100000000
Allocating PCI resources starting at cff00000 (gap: cff00000:10100000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff88022ec00000 s83136 r8192 d23360 u262144
pcpu-alloc: s83136 r8192 d23360 u262144 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 4 5 6 7
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2056547
Policy zone: Normal
PID hash table entries: 4096 (order: 3, 32768 bytes)
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 8141580k/9158656k available (6558k kernel code, 789344k absent, 227732k reserved, 6642k data, 920k init)
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
NR_IRQS:16640 nr_irqs:744 16
spurious 8259A interrupt: IRQ7.
vt handoff: transparent VT on vt#7
Console: colour dummy device 80x25
console [tty0] enabled
allocated 67108864 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2912.046 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 5824.09 BogoMIPS (lpj=11648184)
pid_max: default: 32768 minimum: 301
Security Framework initialized
AppArmor: AppArmor initialized
Yama: becoming mindful.
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
tseg: 00cff00000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
ACPI: Core revision 20110623
ftrace: allocating 27008 entries in 106 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) II X4 641 Quad-Core Processor stepping 00
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 93000
NMI watchdog enabled, takes one hw-pmu counter.
#2
smpboot cpu 2: start_ip = 93000
NMI watchdog enabled, takes one hw-pmu counter.
#3
smpboot cpu 3: start_ip = 93000
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 4 CPUs
Total of 4 processors activated (23295.63 BogoMIPS).
devtmpfs: initialized
EVM: security.selinux
EVM: security.SMACK64
EVM: security.capability
PM: Registering ACPI NVS region at cfda0000 (200704 bytes)
print_constraints: dummy:
RTC time: 10:30:52, date: 03/25/13
NET: Registered protocol family 16
Extended Config Space enabled on 0 nodes
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
Trying to unpack rootfs image as initramfs...
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
Freeing initrd memory: 13884k freed
ACPI: No dock devices found.
HEST: Table not found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff]
pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfed44fff]
pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xfebfffff]
pci 0000:00:00.0: [1022:1705] type 0 class 0x000600
pci 0000:00:02.0: [1022:1707] type 1 class 0x000604
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: [1022:1709] type 1 class 0x000604
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:11.0: [1022:7801] type 0 class 0x000106
pci 0000:00:11.0: reg 10: [io 0xff00-0xff07]
pci 0000:00:11.0: reg 14: [io 0xfe00-0xfe03]
pci 0000:00:11.0: reg 18: [io 0xfd00-0xfd07]
pci 0000:00:11.0: reg 1c: [io 0xfc00-0xfc03]
pci 0000:00:11.0: reg 20: [io 0xfb00-0xfb0f]
pci 0000:00:11.0: reg 24: [mem 0xfe02f000-0xfe02f7ff]
pci 0000:00:12.0: [1022:7807] type 0 class 0x000c03
pci 0000:00:12.0: reg 10: [mem 0xfe02e000-0xfe02efff]
pci 0000:00:12.2: [1022:7808] type 0 class 0x000c03
pci 0000:00:12.2: reg 10: [mem 0xfe02d000-0xfe02d0ff]
pci 0000:00:12.2: supports D1 D2
pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:12.2: PME# disabled
pci 0000:00:13.0: [1022:7807] type 0 class 0x000c03
pci 0000:00:13.0: reg 10: [mem 0xfe02c000-0xfe02cfff]
pci 0000:00:13.2: [1022:7808] type 0 class 0x000c03
pci 0000:00:13.2: reg 10: [mem 0xfe02b000-0xfe02b0ff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
pci 0000:00:14.0: [1022:780b] type 0 class 0x000c05
pci 0000:00:14.1: [1022:780c] type 0 class 0x000101
pci 0000:00:14.1: reg 10: [io 0x0000-0x0007]
pci 0000:00:14.1: reg 14: [io 0x0000-0x0003]
pci 0000:00:14.1: reg 18: [io 0x0000-0x0007]
pci 0000:00:14.1: reg 1c: [io 0x0000-0x0003]
pci 0000:00:14.1: reg 20: [io 0xfa00-0xfa0f]
pci 0000:00:14.2: [1022:780d] type 0 class 0x000403
pci 0000:00:14.2: reg 10: [mem 0xfe024000-0xfe027fff 64bit]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
pci 0000:00:14.3: [1022:780e] type 0 class 0x000601
pci 0000:00:14.4: [1022:780f] type 1 class 0x000604
pci 0000:00:14.5: [1022:7809] type 0 class 0x000c03
pci 0000:00:14.5: reg 10: [mem 0xfe02a000-0xfe02afff]
pci 0000:00:16.0: [1022:7807] type 0 class 0x000c03
pci 0000:00:16.0: reg 10: [mem 0xfe029000-0xfe029fff]
pci 0000:00:16.2: [1022:7808] type 0 class 0x000c03
pci 0000:00:16.2: reg 10: [mem 0xfe028000-0xfe0280ff]
pci 0000:00:16.2: supports D1 D2
pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:16.2: PME# disabled
pci 0000:00:18.0: [1022:1700] type 0 class 0x000600
pci 0000:00:18.1: [1022:1701] type 0 class 0x000600
pci 0000:00:18.2: [1022:1702] type 0 class 0x000600
pci 0000:00:18.3: [1022:1703] type 0 class 0x000600
pci 0000:00:18.4: [1022:1704] type 0 class 0x000600
pci 0000:00:18.5: [1022:1718] type 0 class 0x000600
pci 0000:00:18.6: [1022:1716] type 0 class 0x000600
pci 0000:00:18.7: [1022:1719] type 0 class 0x000600
pci 0000:01:00.0: [1002:683d] type 0 class 0x000300
pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:01:00.0: reg 18: [mem 0xfdd80000-0xfddbffff 64bit]
pci 0000:01:00.0: reg 20: [io 0xee00-0xeeff]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D1 D2 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.1: [1002:aab0] type 0 class 0x000403
pci 0000:01:00.1: reg 10: [mem 0xfddfc000-0xfddfffff 64bit]
pci 0000:01:00.1: supports D1 D2
pci 0000:00:02.0: PCI bridge to [bus 01-01]
pci 0000:00:02.0: bridge window [io 0xe000-0xefff]
pci 0000:00:02.0: bridge window [mem 0xfdd00000-0xfddfffff]
pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200
pci 0000:02:00.0: reg 10: [io 0xde00-0xdeff]
pci 0000:02:00.0: reg 18: [mem 0xfdbff000-0xfdbfffff 64bit pref]
pci 0000:02:00.0: reg 20: [mem 0xfdbf8000-0xfdbfbfff 64bit pref]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:04.0: PCI bridge to [bus 02-02]
pci 0000:00:04.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:04.0: bridge window [mem 0xfdc00000-0xfdcfffff]
pci 0000:00:04.0: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
pci 0000:00:14.4: bridge window [io 0xc000-0xcfff]
pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfdffffff]
pci 0000:00:14.4: bridge window [mem 0xfde00000-0xfdefffff pref]
pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0xd0000000-0xfebfffff] (subtractive decode)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
pci0000:00: Requesting ACPI _OSC control (0x1d)
pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
ACPI _OSC control for PCIe not granted, disabling ASPM
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:01:00.0
i2c-core: driver [aat2870] using legacy suspend method
i2c-core: driver [aat2870] using legacy resume method
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 0000000000098000 - 000000000009ffff
reserve RAM buffer: 00000000cfda0000 - 00000000cfffffff
reserve RAM buffer: 000000022f000000 - 000000022fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 32-bit 14.318180 MHz counter
Switching to clocksource hpet
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-ff]
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: [io 0x0000-0x0cf7 window]
pnp 00:00: [io 0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000c0000-0x000dffff window]
pnp 00:00: [mem 0xfed40000-0xfed44fff window]
pnp 00:00: [mem 0xd0000000-0xfebfffff window]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: [io 0x0010-0x001f]
pnp 00:01: [io 0x0022-0x003f]
pnp 00:01: [io 0x0044-0x004d]
pnp 00:01: [io 0x0050-0x005f]
pnp 00:01: [io 0x0062-0x0063]
pnp 00:01: [io 0x0065-0x006f]
pnp 00:01: [io 0x0074-0x007f]
pnp 00:01: [io 0x0091-0x0093]
pnp 00:01: [io 0x00a2-0x00bf]
pnp 00:01: [io 0x00e0-0x00ef]
pnp 00:01: [io 0x04d0-0x04d1]
pnp 00:01: [io 0x0220-0x0225]
pnp 00:01: [io 0x0290-0x0294]
system 00:01: [io 0x04d0-0x04d1] has been reserved
system 00:01: [io 0x0220-0x0225] has been reserved
system 00:01: [io 0x0290-0x0294] has been reserved
system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:02: [io 0x0900-0x091f]
pnp 00:02: [io 0x0228-0x022f]
pnp 00:02: [io 0x040b]
pnp 00:02: [io 0x04d6]
pnp 00:02: [io 0x0c00-0x0c01]
pnp 00:02: [io 0x0c14]
pnp 00:02: [io 0x0c50-0x0c52]
pnp 00:02: [io 0x0c6c-0x0c6d]
pnp 00:02: [io 0x0c6f]
pnp 00:02: [io 0x0cd0-0x0cd1]
pnp 00:02: [io 0x0cd2-0x0cd3]
pnp 00:02: [io 0x0cd4-0x0cdf]
pnp 00:02: [io 0x0800-0x08fe]
pnp 00:02: [io 0x0a10-0x0a17]
pnp 00:02: [io 0x0b00-0x0b0f]
pnp 00:02: [io 0x0b10-0x0b1f]
pnp 00:02: [io 0x0b20-0x0b3f]
pnp 00:02: [mem 0x00000000-0x00000fff window]
pnp 00:02: [mem 0xfee00400-0xfee00fff window]
pnp 00:02: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
system 00:02: [io 0x0900-0x091f] has been reserved
system 00:02: [io 0x0228-0x022f] has been reserved
system 00:02: [io 0x040b] has been reserved
system 00:02: [io 0x04d6] has been reserved
system 00:02: [io 0x0c00-0x0c01] has been reserved
system 00:02: [io 0x0c14] has been reserved
system 00:02: [io 0x0c50-0x0c52] has been reserved
system 00:02: [io 0x0c6c-0x0c6d] has been reserved
system 00:02: [io 0x0c6f] has been reserved
system 00:02: [io 0x0cd0-0x0cd1] has been reserved
system 00:02: [io 0x0cd2-0x0cd3] has been reserved
system 00:02: [io 0x0cd4-0x0cdf] has been reserved
system 00:02: [io 0x0800-0x08fe] has been reserved
system 00:02: [io 0x0a10-0x0a17] has been reserved
system 00:02: [io 0x0b00-0x0b0f] has been reserved
system 00:02: [io 0x0b10-0x0b1f] has been reserved
system 00:02: [io 0x0b20-0x0b3f] has been reserved
system 00:02: [mem 0xfee00400-0xfee00fff window] has been reserved
system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:03: [dma 4]
pnp 00:03: [io 0x0000-0x000f]
pnp 00:03: [io 0x0080-0x0090]
pnp 00:03: [io 0x0094-0x009f]
pnp 00:03: [io 0x00c0-0x00df]
pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:04: [irq 0 disabled]
pnp 00:04: [irq 8]
pnp 00:04: [mem 0xfed00000-0xfed003ff]
pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:05: [io 0x0070-0x0073]
pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:06: [io 0x0061]
pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:07: [io 0x00f0-0x00ff]
pnp 00:07: [irq 13]
pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:08: [io 0x03f8-0x03ff]
pnp 00:08: [irq 4]
pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:09: [mem 0xe0000000-0xefffffff]
system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0a: [mem 0x000d4400-0x000d7fff]
pnp 00:0a: [mem 0x000f0000-0x000f7fff]
pnp 00:0a: [mem 0x000f8000-0x000fbfff]
pnp 00:0a: [mem 0x000fc000-0x000fffff]
pnp 00:0a: [mem 0xcfda0000-0xcfdfffff]
pnp 00:0a: [mem 0xffff0000-0xffffffff]
pnp 00:0a: [mem 0x00000000-0x0009ffff]
pnp 00:0a: [mem 0x00100000-0xcfd9ffff]
pnp 00:0a: [mem 0xcfe00000-0xcfefffff]
pnp 00:0a: [mem 0xcff00000-0xcfffffff]
pnp 00:0a: [mem 0x00000000-0xffffffffffffffff disabled]
pnp 00:0a: [mem 0xfec00000-0xfec00fff]
pnp 00:0a: [mem 0xfee00000-0xfee00fff]
pnp 00:0a: [mem 0xfff80000-0xfffeffff]
pnp 00:0a: [Firmware Bug]: [mem 0x00000000-0xffffffffffffffff disabled] covers only part of AMD MMCONFIG area [mem 0xe0000000-0xefffffff]; adding more reservations
system 00:0a: [mem 0x000d4400-0x000d7fff] has been reserved
system 00:0a: [mem 0x000f0000-0x000f7fff] could not be reserved
system 00:0a: [mem 0x000f8000-0x000fbfff] could not be reserved
system 00:0a: [mem 0x000fc000-0x000fffff] could not be reserved
system 00:0a: [mem 0xcfda0000-0xcfdfffff] could not be reserved
system 00:0a: [mem 0xffff0000-0xffffffff] has been reserved
system 00:0a: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0a: [mem 0x00100000-0xcfd9ffff] could not be reserved
system 00:0a: [mem 0xcfe00000-0xcfefffff] has been reserved
system 00:0a: [mem 0xcff00000-0xcfffffff] could not be reserved
system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:0a: [mem 0xfee00000-0xfee00fff] could not be reserved
system 00:0a: [mem 0xfff80000-0xfffeffff] has been reserved
system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:01:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref]
pci 0000:00:02.0: PCI bridge to [bus 01-01]
pci 0000:00:02.0: bridge window [io 0xe000-0xefff]
pci 0000:00:02.0: bridge window [mem 0xfdd00000-0xfddfffff]
pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:04.0: PCI bridge to [bus 02-02]
pci 0000:00:04.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:04.0: bridge window [mem 0xfdc00000-0xfdcfffff]
pci 0000:00:04.0: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
pci 0000:00:14.4: PCI bridge to [bus 03-03]
pci 0000:00:14.4: bridge window [io 0xc000-0xcfff]
pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfdffffff]
pci 0000:00:14.4: bridge window [mem 0xfde00000-0xfdefffff pref]
pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:04.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
pci_bus 0000:00: resource 9 [mem 0xd0000000-0xfebfffff]
pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
pci_bus 0000:01: resource 1 [mem 0xfdd00000-0xfddfffff]
pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:02: resource 1 [mem 0xfdc00000-0xfdcfffff]
pci_bus 0000:02: resource 2 [mem 0xfdb00000-0xfdbfffff 64bit pref]
pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfdffffff]
pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdefffff pref]
pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000dffff]
pci_bus 0000:03: resource 8 [mem 0xfed40000-0xfed44fff]
pci_bus 0000:03: resource 9 [mem 0xd0000000-0xfebfffff]
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 4096 (order: 5, 131072 bytes)
UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
NET: Registered protocol family 1
pci 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:12.0: PCI INT A disabled
pci 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:12.2: PCI INT B disabled
pci 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:13.0: PCI INT A disabled
pci 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:13.2: PCI INT B disabled
pci 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:14.5: PCI INT C disabled
pci 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:16.0: PCI INT A disabled
pci 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:16.2: PCI INT B disabled
pci 0000:01:00.0: Boot video device
PCI: CLS 64 bytes, default 64
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff8800cbd9e000 - ffff8800cfd9e000
software IO TLB at phys 0xcbd9e000 - 0xcfd9e000
perf: AMD IBS detected (0x000000ff)
audit: initializing netlink socket (disabled)
type=2000 audit(1364207451.896:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
fuse init (API version 7.17)
msgmni has been set to 15928
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
ACPI: acpi_idle registered with cpuidle
ERST: Table is not found!
GHES: HEST is not enabled!
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Linux agpgart interface v0.103
brd: module loaded
loop: module loaded
ahci 0000:00:11.0: version 3.0
ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:11.0: irq 40 for MSI/MSI-X
ahci 0000:00:11.0: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfe02f000 port 0xfe02f100 irq 40
ata2: SATA max UDMA/133 abar m2048@0xfe02f000 port 0xfe02f180 irq 40
ata3: SATA max UDMA/133 abar m2048@0xfe02f000 port 0xfe02f200 irq 40
ata4: SATA max UDMA/133 abar m2048@0xfe02f000 port 0xfe02f280 irq 40
pata_acpi 0000:00:14.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pata_acpi 0000:00:14.1: PCI INT B disabled
Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
QUIRK: Enable AMD PLL fix
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe02d000
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:13.2: debug port 1
ehci_hcd 0000:00:13.2: irq 17, io mem 0xfe02b000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 5 ports detected
ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:16.2: EHCI Host Controller
ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:16.2: debug port 1
ehci_hcd 0000:00:16.2: irq 17, io mem 0xfe028000
ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:12.0: irq 18, io mem 0xfe02e000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe02c000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 5 ports detected
ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:14.5: OHCI Host Controller
ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe02a000
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:16.0: OHCI Host Controller
ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
ohci_hcd 0000:00:16.0: irq 18, io mem 0xfe029000
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver libusual
i8042: PNP: No PS/2 controller found. Probing ports directly.
i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
i8042: If AUX port is really absent please use the 'i8042.noaux' option
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: PIONEER DVD-RW DVR-216D, 1.07, max UDMA/66
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66 (SET_XFERMODE skipped)
ata1.00: ATA-7: WDC WD1600JS-22NCB1, 10.02E02, max UDMA/133
ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata2.00: ATA-8: ST500DM002-1BD142, KC45, max UDMA/133
ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-22N 10.0 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
ata3.00: ATA-7: SAMSUNG SP0812C, SU100-34, max UDMA7
ata3.00: 156368016 sectors, multi 0: LBA48
sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST500DM002-1BD14 KC45 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 1:0:0:0: [sdb] 4096-byte physical blocks
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA SAMSUNG SP0812C SU10 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 156368016 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 < sdc5 >
sd 2:0:0:0: [sdc] Attached SCSI disk
sda: sda1 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 3:0:0:0: CD-ROM PIONEER DVD-RW DVR-216D 1.07 PQ: 0 ANSI: 5
serio: i8042 KBD port at 0x60,0x64 irq 1
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Registering the dns_resolver key type
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
Magic number: 5:397:528
rtc_cmos 00:05: setting system clock to 2013-03-25 10:30:53 UTC (1364207453)
powernow-k8: Found 1 AMD Athlon(tm) II X4 641 Quad-Core Processor (4 cpu cores) (version 2.20.00)
powernow-k8: 0 : pstate 0 (2800 MHz)
powernow-k8: 1 : pstate 1 (2500 MHz)
powernow-k8: 2 : pstate 2 (2200 MHz)
powernow-k8: 3 : pstate 3 (2000 MHz)
powernow-k8: 4 : pstate 4 (1800 MHz)
powernow-k8: 5 : pstate 5 (1400 MHz)
powernow-k8: 6 : pstate 6 (1100 MHz)
powernow-k8: 7 : pstate 7 (800 MHz)
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
sd 1:0:0:0: [sdb] Attached SCSI disk
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
sr 3:0:0:0: Attached scsi generic sg3 type 5
Freeing unused kernel memory: 920k freed
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 1616k freed
Freeing unused kernel memory: 1200k freed
udevd[102]: starting version 175
Refined TSC clocksource calibration: 2911.982 MHz.
Switching to clocksource tsc
usb 4-1: new low-speed USB device number 2 using ohci_hcd
pata_atiixp 0000:00:14.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 41 for MSI/MSI-X
r8169 0000:02:00.0: eth0: RTL8168evl/8111evl at 0xffffc90000c1a000, 50:e5:49:5a:83:b2, XID 0c900800 IRQ 41
r8169 0000:02:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:12.0/usb4/4-1/4-1:1.0/input/input2
generic-usb 0003:046D:C30E.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:12.0-1/input0
input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:12.0/usb4/4-1/4-1:1.1/input/input3
generic-usb 0003:046D:C30E.0002: input,hidraw1: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:12.0-1/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 4-2: new full-speed USB device number 3 using ohci_hcd
input: A4Tech USB Mouse as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2:1.0/input/input4
generic-usb 0003:09DA:0080.0003: input,hidraw2: USB HID v1.11 Mouse [A4Tech USB Mouse] on usb-0000:00:12.0-2/input0
EXT4-fs (sdb5): INFO: recovery required on readonly filesystem
EXT4-fs (sdb5): write access will be enabled during recovery
EXT4-fs (sdb5): orphan cleanup on readonly fs
EXT4-fs (sdb5): ext4_orphan_cleanup: deleting unreferenced inode 1574566
EXT4-fs (sdb5): 1 orphan inode deleted
EXT4-fs (sdb5): recovery complete
EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null)
ADDRCONF(NETDEV_UP): eth0: link is not ready
udevd[372]: starting version 175
Adding 9727996k swap on /dev/sdb6. Priority:-1 extents:1 across:9727996k
lp: driver loaded but no devices found
it87: Found IT8720F chip at 0x228, revision 8
it87: Routing internal VCCH to in7
it87: Beeping is supported
hwmon_vid: Unknown VRM version of your x86 CPU
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
Disabling lock debugging due to kernel taint
ip6_tables: (C) 2000-2006 Netfilter Core Team
[fglrx] Maximum main memory to use for locked dma buffers: 7734 MBytes.
[fglrx] vendor: 1002 device: 683d count: 1
[fglrx] ioport: bar 4, base 0xee00, size: 0x100
pci 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:01:00.0: setting latency timer to 64
[fglrx] Kernel PAT support is enabled
[fglrx] module loaded - fglrx 9.0.2 [Sep 28 2012] with 1 minors
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
hda_codec: ALC889: BIOS auto-probing.
input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input5
input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
input: HD-Audio Generic Line-Out as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
snd_hda_intel 0000:01:00.1: irq 42 for MSI/MSI-X
snd_hda_intel 0000:01:00.1: setting latency timer to 64
Too many HDMI devices
Too many HDMI devices
Too many HDMI devices
Too many HDMI devices
Too many HDMI devices
Too many HDMI devices
Too many HDMI devices
Too many HDMI devices
hda-codec: out of range cmd 0:0:6f90:707:0
hda-codec: out of range cmd 0:0:6f90:708:85
hda-codec: out of range cmd 0:0:6f90:f00:c
hda-codec: out of range cmd 0:0:6f90:709:0
hda-codec: out of range cmd 0:0:6f90:f09:0
hda-codec: out of range cmd 0:0:e0:f0d:0
HDMI status: Codec=0 Pin=2 Presence_Detect=0 ELD_Valid=0
HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
HDMI status: Codec=0 Pin=7 Presence_Detect=0 ELD_Valid=0
HDMI status: Codec=0 Pin=9 Presence_Detect=0 ELD_Valid=0
HDMI status: Codec=0 Pin=28560 Presence_Detect=1 ELD_Valid=1
hda-codec: out of range cmd 0:0:6f90:f2e:8
hda_codec: cannot build controls for #0 (error -16)
hda_codec: cannot revert codec
snd_hda_intel 0000:01:00.1: PCI INT B disabled
snd_hda_intel: probe of 0000:01:00.1 failed with error -16
vesafb: mode is 1920x1200x32, linelength=7680, pages=0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011c00000, using 9024k, total 9024k
Console: switching to colour frame buffer device 240x75
fb0: VESA VGA frame buffer device
EXT4-fs (sdb5): re-mounted. Opts: errors=remount-ro
EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (sdb7): mounted filesystem with ordered data mode. Opts: (null)
kjournald starting. Commit interval 5 seconds
EXT3-fs (sdc5): using internal journal
EXT3-fs (sdc5): mounted filesystem with ordered data mode
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
FS-Cache: Loaded
FS-Cache: Netfs 'nfs' registered for caching
Installing knfsd (copyright (C) 1996 [email protected]).
EXT4-fs (sdb8): mounted filesystem with ordered data mode. Opts: (null)
init: failsafe main process (1070) killed by TERM signal
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
r8169 0000:02:00.0: eth0: link down
r8169 0000:02:00.0: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth0: link is not ready
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
fglrx_pci 0000:01:00.0: irq 42 for MSI/MSI-X
[fglrx] Firegl kernel thread PID: 1717
[fglrx] Firegl kernel thread PID: 1718
[fglrx] Firegl kernel thread PID: 1719
[fglrx] IRQ 42 Enabled
[fglrx] Gart USWC size:1280 M.
[fglrx] Gart cacheable size:508 M.
[fglrx] Reserved FB block: Shared offset:0, size:1000000
[fglrx] Reserved FB block: Unshared offset:f8fc000, size:404000
[fglrx] Reserved FB block: Unshared offset:3ffee000, size:12000
[fglrx:firegl_pplib_notify_event] *ERROR* PPLIB: PPLib Notify Event failed!
[fglrx:firegl_pplib_notify_event] *ERROR* ulEventType = 00000023, ulEventData = 00000001
vboxdrv: Found 4 processor cores.
vboxdrv: fAsync=0 offMin=0x562 offMax=0x41df
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 4.1.12_Ubuntu (interface 0x00190000).
vboxpci: IOMMU not found (not registered)
r8169 0000:02:00.0: eth0: link up
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
postgres (3523): /proc/3523/oom_adj is deprecated, please use /proc/3523/oom_score_adj instead.
init: plymouth-stop pre-start process (3606) terminated with status 1
eth0: no IPv6 routers present
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
non-matching-uid symlink following attempted in sticky world-writable directory by pool (fsuid 1000 != 1001)
nfs: server malandhir not responding, timed out
nfs: server malandhir not responding, timed out
nfs: server malandhir not responding, timed out
nfs: server malandhir not responding, timed out
type=1701 audit(1364237000.185:2): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=5993 comm="chromium-browse" reason="seccomp" sig=0 syscall=39 compat=0 ip=0x7f2fd1154ed9 code=0x50001
type=1701 audit(1364237002.761:3): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6016 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.761:4): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6016 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.761:5): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6016 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.761:6): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6016 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.761:7): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6016 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.785:8): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6024 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.785:9): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6024 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.785:10): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6024 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
type=1701 audit(1364237002.785:11): auid=4294967295 uid=1000 gid=100 ses=4294967295 pid=6024 comm="chromium-browse" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f2fd114b205 code=0x50002
show_signal_msg: 36 callbacks suppressed
eom[7719]: segfault at 7f8f3c1ab398 ip 00007f8f4e96f941 sp 00007fff0db1f420 error 4 in libfreetype.so.6.8.0[7f8f4e948000+96000]
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
serial 00:08: disabled
sd 2:0:0:0: [sdc] Synchronizing SCSI cache
sd 2:0:0:0: [sdc] Stopping disk
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
pata_atiixp 0000:00:14.1: PCI INT B disabled
[fglrx] IRQ 42 Disabled
[fglrx] Preparing suspend fglrx in kernel.
ohci_hcd 0000:00:12.0: PCI INT A disabled
sd 1:0:0:0: [sdb] Stopping disk
ehci_hcd 0000:00:16.2: PCI INT B disabled
ehci_hcd 0000:00:13.2: PCI INT B disabled
ehci_hcd 0000:00:12.2: PCI INT B disabled
ohci_hcd 0000:00:13.0: PCI INT A disabled
ohci_hcd 0000:00:16.0: PCI INT A disabled
ohci_hcd 0000:00:14.5: PCI INT C disabled
snd_hda_intel 0000:00:14.2: PCI INT A disabled
PM: suspend of drv:snd_hda_intel dev:0000:00:14.2 complete after 118.405 msecs
PM: suspend of drv:sd dev:2:0:0:0 complete after 239.279 msecs
PM: suspend of drv:scsi dev:target2:0:0 complete after 239.239 msecs
PM: suspend of drv:scsi dev:host2 complete after 238.554 msecs
PM: suspend of drv:sd dev:1:0:0:0 complete after 366.601 msecs
PM: suspend of drv:scsi dev:target1:0:0 complete after 366.564 msecs
PM: suspend of drv:scsi dev:host1 complete after 366.089 msecs
PM: suspend of drv:ahci dev:0000:00:11.0 complete after 363.736 msecs
[fglrx] Suspending fglrx in kernel completed.
[fglrx] Power down the ASIC .
PM: suspend of drv:fglrx_pci dev:0000:01:00.0 complete after 373.555 msecs
PM: suspend of drv:pcieport dev:0000:00:02.0 complete after 370.839 msecs
PM: suspend of drv: dev:pci0000:00 complete after 370.847 msecs
PM: suspend of devices complete after 375.027 msecs
PM: suspend devices took 0.372 seconds
r8169 0000:02:00.0: PME# enabled
pcieport 0000:00:04.0: wake-up capability enabled by ACPI
ehci_hcd 0000:00:16.2: PME# enabled
ehci_hcd 0000:00:16.2: wake-up capability enabled by ACPI
ohci_hcd 0000:00:16.0: wake-up capability enabled by ACPI
ohci_hcd 0000:00:14.5: wake-up capability enabled by ACPI
ehci_hcd 0000:00:13.2: PME# enabled
ehci_hcd 0000:00:13.2: wake-up capability enabled by ACPI
ohci_hcd 0000:00:13.0: wake-up capability enabled by ACPI
ehci_hcd 0000:00:12.2: PME# enabled
ehci_hcd 0000:00:12.2: wake-up capability enabled by ACPI
ohci_hcd 0000:00:12.0: wake-up capability enabled by ACPI
PM: late suspend of devices complete after 60.829 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
CPU 1 is now offline
CPU 2 is now offline
CPU 3 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
Booting Node 0 Processor 1 APIC 0x1
smpboot cpu 1: start_ip = 93000
Calibrating delay loop (skipped) already calibrated this CPU
NMI watchdog enabled, takes one hw-pmu counter.
CPU1 is up
Booting Node 0 Processor 2 APIC 0x2
smpboot cpu 2: start_ip = 93000
Calibrating delay loop (skipped) already calibrated this CPU
NMI watchdog enabled, takes one hw-pmu counter.
CPU2 is up
Booting Node 0 Processor 3 APIC 0x3
smpboot cpu 3: start_ip = 93000
Calibrating delay loop (skipped) already calibrated this CPU
NMI watchdog enabled, takes one hw-pmu counter.
CPU3 is up
ACPI: Waking up from system sleep state S3
pci 0000:00:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x2000)
pcieport 0000:00:02.0: restoring config space at offset 0x9 (was 0x10001, writing 0xdff1d001)
pcieport 0000:00:02.0: restoring config space at offset 0x8 (was 0x0, writing 0xfdd0fdd0)
pcieport 0000:00:02.0: restoring config space at offset 0x7 (was 0x2000e1e1, writing 0xe1e1)
pcieport 0000:00:02.0: restoring config space at offset 0x6 (was 0x0, writing 0x10100)
pcieport 0000:00:02.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
ahci 0000:00:11.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
ahci 0000:00:11.0: restoring config space at offset 0x1 (was 0x2300007, writing 0x2300407)
ohci_hcd 0000:00:12.0: wake-up capability disabled by ACPI
ehci_hcd 0000:00:12.2: BAR 0: set to [mem 0xfe02d000-0xfe02d0ff] (PCI address [0xfe02d000-0xfe02d0ff])
ehci_hcd 0000:00:12.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00013)
ehci_hcd 0000:00:12.2: wake-up capability disabled by ACPI
ehci_hcd 0000:00:12.2: PME# disabled
ohci_hcd 0000:00:13.0: wake-up capability disabled by ACPI
ehci_hcd 0000:00:13.2: BAR 0: set to [mem 0xfe02b000-0xfe02b0ff] (PCI address [0xfe02b000-0xfe02b0ff])
ehci_hcd 0000:00:13.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00013)
ehci_hcd 0000:00:13.2: wake-up capability disabled by ACPI
ehci_hcd 0000:00:13.2: PME# disabled
snd_hda_intel 0000:00:14.2: restoring config space at offset 0xf (was 0x100, writing 0x10a)
snd_hda_intel 0000:00:14.2: restoring config space at offset 0x3 (was 0x0, writing 0x2010)
ohci_hcd 0000:00:14.5: wake-up capability disabled by ACPI
ohci_hcd 0000:00:16.0: wake-up capability disabled by ACPI
ehci_hcd 0000:00:16.2: BAR 0: set to [mem 0xfe028000-0xfe0280ff] (PCI address [0xfe028000-0xfe0280ff])
ehci_hcd 0000:00:16.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00013)
ehci_hcd 0000:00:16.2: wake-up capability disabled by ACPI
ehci_hcd 0000:00:16.2: PME# disabled
fglrx_pci 0000:01:00.0: restoring config space at offset 0x1 (was 0x100007, writing 0x100403)
pci 0000:01:00.1: restoring config space at offset 0xf (was 0x2ff, writing 0x20b)
pci 0000:01:00.1: restoring config space at offset 0x4 (was 0x4, writing 0xfddfc004)
pci 0000:01:00.1: restoring config space at offset 0x3 (was 0x800000, writing 0x800010)
pci 0000:01:00.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100002)
r8169 0000:02:00.0: restoring config space at offset 0x1 (was 0x100007, writing 0x100407)
PM: early resume of devices complete after 46.872 msecs
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pata_atiixp 0000:00:14.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pcieport 0000:00:04.0: wake-up capability disabled by ACPI
r8169 0000:02:00.0: PME# disabled
fglrx_pci 0000:01:00.0: setting latency timer to 64
serial 00:08: activated
sd 0:0:0:0: [sda] Starting disk
sd 1:0:0:0: [sdb] Starting disk
sd 2:0:0:0: [sdc] Starting disk
[fglrx] Power up the ASIC
[fglrx] Preparing resume fglrx in kernel.
[fglrx] Resuming fglrx in kernel completed.
[fglrx] IRQ 42 Enabled
PM: resume of drv:hub dev:6-0:1.0 complete after 102.173 msecs
PM: resume of drv:hub dev:5-0:1.0 complete after 102.384 msecs
PM: resume of drv:hub dev:7-0:1.0 complete after 102.068 msecs
PM: resume of drv: dev:ep_00 complete after 102.146 msecs
PM: resume of drv: dev:ep_00 complete after 102.288 msecs
PM: resume of drv: dev:ep_00 complete after 102.072 msecs
PM: resume of drv: dev:ep_81 complete after 102.214 msecs
PM: resume of drv: dev:ep_81 complete after 102.365 msecs
PM: resume of drv: dev:ep_81 complete after 102.109 msecs
PM: resume of drv: dev:ep_00 complete after 102.606 msecs
PM: resume of drv:hub dev:4-0:1.0 complete after 102.786 msecs
PM: resume of drv: dev:ep_81 complete after 102.643 msecs
PM: resume of drv:r8169 dev:0000:02:00.0 complete after 103.554 msecs
PM: resume of drv:usbhid dev:4-2:1.0 complete after 150.662 msecs
PM: resume of drv: dev:ep_00 complete after 150.616 msecs
PM: resume of drv: dev:ep_81 complete after 150.694 msecs
PM: resume of drv:usbhid dev:4-1:1.1 complete after 154.716 msecs
PM: resume of drv: dev:ep_82 complete after 154.699 msecs
PM: resume of drv:usbhid dev:4-1:1.0 complete after 154.833 msecs
PM: resume of drv: dev:ep_81 complete after 154.851 msecs
PM: resume of drv: dev:ep_00 complete after 164.555 msecs
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66 (SET_XFERMODE skipped)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/133
PM: resume of drv:sd dev:2:0:0:0 complete after 3316.161 msecs
PM: resume of drv:scsi_device dev:2:0:0:0 complete after 3316.213 msecs
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: configured for UDMA/133
PM: resume of drv:sd dev:1:0:0:0 complete after 4341.839 msecs
PM: resume of drv:scsi_device dev:1:0:0:0 complete after 4341.903 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
PM: resume of drv:sd dev:0:0:0:0 complete after 4651.875 msecs
PM: resume of drv:scsi_device dev:0:0:0:0 complete after 4651.940 msecs
PM: resume of drv:scsi_disk dev:0:0:0:0 complete after 4629.915 msecs
PM: resume of devices complete after 4653.710 msecs
PM: resume devices took 4.652 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
r8169 0000:02:00.0: eth0: link down
r8169 0000:02:00.0: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
r8169 0000:02:00.0: eth0: link up
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present