dmesg - ramspeed
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.2.1-linaro-omap (root@adam-Gumstix) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-7ubuntu2) ) #3 PREEMPT Thu Jul 26 17:05:26 PDT 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Gumstix Overo
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 128000
[ 0.000000] free_area_init_node: node 0, pgdat c0924f7c, node_mem_map c0e96000
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126976
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 500MB = 500MB total
[ 0.000000] Memory: 490556k/490556k available, 33732k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc085f770 (8542 kB)
[ 0.000000] .init : 0xc0860000 - 0xc08b9000 ( 356 kB)
[ 0.000000] .data : 0xc08ba000 - 0xc09274f8 ( 438 kB)
[ 0.000000] .bss : 0xc092751c - 0xc0e957cc (5561 kB)
[ 0.000000] NR_IRQS:410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.065246] Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
[ 0.106292] pid_max: default: 32768 minimum: 301
[ 0.111755] Security Framework initialized
[ 0.116241] AppArmor: AppArmor initialized
[ 0.120819] Mount-cache hash table entries: 512
[ 0.132354] CPU: Testing write buffer coherency: ok
[ 0.137939] ftrace: allocating 22297 entries in 66 pages
[ 0.215026] Setting up static identity map for 0x805e5b70 - 0x805e5bc8
[ 0.226654] devtmpfs: initialized
[ 0.246276] print_constraints: dummy:
[ 0.252746] NET: Registered protocol family 16
[ 0.258636] GPMC revision 5.0
[ 0.275024] OMAP GPIO hardware version 2.5
[ 0.294952] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.320404] Reprogramming SDRC clock to 400000000 Hz
[ 0.326110] dpll3_m2_clk rate change failed: -22
[ 0.331085] Found NAND on CS0
[ 0.334259] Registering NAND on CS0
[ 0.356536] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.386535] omap-mcbsp.2: alias fck already exists
[ 0.393035] omap-mcbsp.3: alias fck already exists
[ 0.404083] Calibrating delay loop (skipped) already calibrated this CPU
[ 0.411376] Switched to new clocking rate (Crystal/Core/MPU): 26.0/400/500 MHz
[ 0.420013] OMAP DMA hardware revision 5.0
[ 0.537994] bio: create slab at 0
[ 0.547485] machine_constraints_voltage: vads7846: override min_uV, 1 -> 3300000
[ 0.547546] machine_constraints_voltage: vads7846: override max_uV, 2147483647 -> 3300000
[ 0.547576] print_constraints: vads7846: 3300 mV
[ 0.553283] reg-fixed-voltage reg-fixed-voltage.1: vads7846 supplying 3300000uV
[ 0.559600] SCSI subsystem initialized
[ 0.578613] usbcore: registered new interface driver usbfs
[ 0.586395] usbcore: registered new interface driver hub
[ 0.593353] usbcore: registered new device driver usb
[ 0.605224] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
[ 0.624389] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.630859] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.639648] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.659057] machine_constraints_voltage: VUSB1V5: override min_uV, 1 -> 1500000
[ 0.659088] machine_constraints_voltage: VUSB1V5: override max_uV, 2147483647 -> 1500000
[ 0.659149] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.669036] machine_constraints_voltage: VUSB1V8: override min_uV, 1 -> 1800000
[ 0.669067] machine_constraints_voltage: VUSB1V8: override max_uV, 2147483647 -> 1800000
[ 0.669097] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.678466] machine_constraints_voltage: VUSB3V1: override min_uV, 1 -> 3100000
[ 0.678527] machine_constraints_voltage: VUSB3V1: override max_uV, 2147483647 -> 3100000
[ 0.678558] print_constraints: VUSB3V1: 3100 mV normal standby
[ 0.691986] twl4030_usb twl4030_usb: HW_CONDITIONS 0x10/16; link 0
[ 0.692932] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.706115] print_constraints: VMMC1: 1850 3150 mV at 3150 mV normal standby
[ 0.717193] print_constraints: VDAC: 1800 mV normal standby
[ 0.726287] print_constraints: VDVI: 1800 mV normal standby
[ 0.733520] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 400 kHz
[ 0.746978] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.758697] NetLabel: Initializing
[ 0.762695] NetLabel: domain hash size = 128
[ 0.767303] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.773071] NetLabel: unlabeled traffic allowed by default
[ 0.779113] Switching to clocksource 32k_counter
[ 0.898223] AppArmor: AppArmor Filesystem Enabled
[ 1.002716] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 1.016204] twl4030_usb twl4030_usb: twl4030_phy_resume
[ 1.016784] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 1.016815] musb-hdrc: MHDRC RTL version 1.800
[ 1.016845] musb-hdrc: setup fifo_mode 4
[ 1.016876] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 1.020935] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[ 1.030731] NET: Registered protocol family 2
[ 1.036376] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.046020] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.054687] TCP bind hash table entries: 16384 (order: 7, 589824 bytes)
[ 1.074371] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.081390] TCP reno registered
[ 1.084777] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 1.091491] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 1.099395] NET: Registered protocol family 1
[ 1.106109] RPC: Registered named UNIX socket transport module.
[ 1.112487] RPC: Registered udp transport module.
[ 1.117492] RPC: Registered tcp transport module.
[ 1.122497] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.130432] Trying to unpack rootfs image as initramfs...
[ 1.395324] Freeing initrd memory: 1948K
[ 1.411224] audit: initializing netlink socket (disabled)
[ 1.417663] type=2000 audit(1.367:1): initialized
[ 1.579833] Kprobe smoke test started
[ 1.616394] Kprobe smoke test passed successfully
[ 1.646575] JFFS2 version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9\xffffffa9 2001-2006 Red Hat, Inc.
[ 1.658660] Btrfs loaded
[ 1.661773] msgmni has been set to 961
[ 1.673858] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.682220] io scheduler noop registered
[ 1.686584] io scheduler deadline registered
[ 1.691436] io scheduler cfq registered (default)
[ 1.701843] OMAP DSS rev 2.0
[ 1.736267] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
[ 1.748077] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
[ 1.757476] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
[ 1.765441] console [ttyO2] enabled, bootconsole disabled
[ 1.778656] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
[ 1.789916] [drm] Initialized drm 1.1.0 20060810
[ 1.842376] brd: module loaded
[ 1.874389] loop: module loaded
[ 1.881103] twl4030_madc twl4030_madc: clk disabled, enabling
[ 1.898010] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.905792] omap2-nand driver initializing
[ 1.910919] ONFI flash detected
[ 1.914550] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit)
[ 1.923858] Creating 5 MTD partitions on "omap2-nand.0":
[ 1.929595] 0x000000000000-0x000000080000 : "xloader"
[ 1.946258] 0x000000080000-0x000000240000 : "uboot"
[ 1.959350] 0x000000240000-0x000000280000 : "uboot environment"
[ 1.972808] 0x000000280000-0x000000680000 : "linux"
[ 1.986816] 0x000000680000-0x000020000000 : "rootfs"
[ 2.279113] OneNAND driver initializing
[ 2.290039] smsc911x: Driver version 2008-10-21
[ 2.320648] smsc911x-mdio: probed
[ 2.325012] smsc911x smsc911x.0: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
[ 2.335632] smsc911x smsc911x.0: eth0: MAC Address: 00:15:c9:28:f4:72
[ 2.342834] smsc911x: Driver version 2008-10-21
[ 2.349945] usbcore: registered new interface driver asix
[ 2.356658] usbcore: registered new interface driver cdc_ether
[ 2.363159] cdc_ncm: 04-Aug-2011
[ 2.367279] usbcore: registered new interface driver cdc_ncm
[ 2.375854] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.383117] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
[ 2.383605] ehci-omap ehci-omap.0: failed to get ehci port1 regulator
[ 3.385772] ehci-omap ehci-omap.0: phy reset operation timed out
[ 3.385803] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
[ 3.385864] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
[ 3.385894] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 3.394500] drivers/usb/core/inode.c: creating file 'devices'
[ 3.395050] drivers/usb/core/inode.c: creating file '001'
[ 3.398895] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 3.407623] ehci-omap ehci-omap.0: park 0
[ 3.407714] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 3.413879] ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 3.413909] ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[ 3.424957] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.432434] usb usb1: default language 0x0409
[ 3.432586] usb usb1: udev 1, busnum 1, minor = 0
[ 3.432678] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.439880] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.447601] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.453277] usb usb1: Manufacturer: Linux 3.2.1-linaro-omap ehci_hcd
[ 3.460083] usb usb1: SerialNumber: ehci-omap.0
[ 3.468780] usb usb1: usb_probe_device
[ 3.468811] usb usb1: configuration #1 chosen from 1 choice
[ 3.469879] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 3.472076] hub 1-0:1.0: usb_probe_interface
[ 3.472137] hub 1-0:1.0: usb_probe_interface - got id
[ 3.472198] hub 1-0:1.0: USB hub found
[ 3.476470] hub 1-0:1.0: 3 ports detected
[ 3.481018] hub 1-0:1.0: standalone hub
[ 3.481048] hub 1-0:1.0: individual port power switching
[ 3.481079] hub 1-0:1.0: individual port over-current protection
[ 3.481109] hub 1-0:1.0: power on to power good time: 20ms
[ 3.481811] hub 1-0:1.0: local power source is good
[ 3.481842] hub 1-0:1.0: enabling power on all ports
[ 3.485076] drivers/usb/core/inode.c: creating file '001'
[ 3.486022] ehci-omap ehci-omap.0: ...powerup ports...
[ 3.511474] Initializing USB Mass Storage driver...
[ 3.517669] usbcore: registered new interface driver usb-storage
[ 3.524200] USB Mass Storage support registered.
[ 3.531066] usbcore: registered new interface driver libusual
[ 3.537811] gadget: using random self ethernet address
[ 3.543518] gadget: using random host ethernet address
[ 3.551757] usb0: MAC d6:2c:de:aa:ba:99
[ 3.555847] usb0: HOST MAC 6a:d0:c7:c5:b1:5f
[ 3.560821] gadget: Ethernet Gadget, version: Memorial Day 2008
[ 3.567352] gadget: g_ether ready
[ 3.571075] musb-hdrc musb-hdrc: MUSB HDRC host driver
[ 3.576904] drivers/usb/core/inode.c: creating file '002'
[ 3.579315] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2
[ 3.588287] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 3.589355] usb usb2: default language 0x0409
[ 3.589538] usb usb2: udev 1, busnum 2, minor = 128
[ 3.589538] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.596862] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.604583] usb usb2: Product: MUSB HDRC host driver
[ 3.609832] usb usb2: Manufacturer: Linux 3.2.1-linaro-omap musb-hcd
[ 3.616638] usb usb2: SerialNumber: musb-hdrc
[ 3.624206] usb usb2: usb_probe_device
[ 3.624237] usb usb2: configuration #1 chosen from 1 choice
[ 3.624481] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 3.626068] hub 2-0:1.0: usb_probe_interface
[ 3.626098] hub 2-0:1.0: usb_probe_interface - got id
[ 3.626190] hub 2-0:1.0: USB hub found
[ 3.630767] hub 2-0:1.0: 1 port detected
[ 3.634948] hub 2-0:1.0: standalone hub
[ 3.634948] hub 2-0:1.0: individual port power switching
[ 3.634979] hub 2-0:1.0: no over-current protection
[ 3.635009] hub 2-0:1.0: Single TT
[ 3.635040] hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 3.635070] hub 2-0:1.0: power on to power good time: 10ms
[ 3.635131] hub 2-0:1.0: 100mA bus power budget for each child
[ 3.635314] hub 2-0:1.0: local power source is good
[ 3.635345] hub 2-0:1.0: enabling power on all ports
[ 3.638092] drivers/usb/core/inode.c: creating file '001'
[ 3.642944] mousedev: PS/2 mouse device common for all mice
[ 3.656799] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0
[ 3.674224] twl_rtc twl_rtc: Power up reset detected.
[ 3.685943] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 3.695007] i2c /dev entries driver
[ 3.704254] Driver for 1-wire Dallas network protocol.
[ 3.718597] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 1
[ 3.729980] hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 3.953247] Registered led device: overo:red:gpio21
[ 3.954467] Registered led device: overo:blue:gpio22
[ 3.958251] Registered led device: overo:blue:COM
[ 3.984039] usbcore: registered new interface driver usbhid
[ 3.990478] usbhid: USB HID core driver
[ 3.995483] omap-iommu omap-iommu.0: isp registered
[ 4.013519] overo SoC init
[ 4.128234] asoc: twl4030-hifi omap-mcbsp-dai.1 mapping ok
[ 4.146697] ALSA device list:
[ 4.149902] #0: overo
[ 4.152832] oprofile: hardware counters not available
[ 4.158203] oprofile: using timer interrupt.
[ 4.163848] TCP cubic registered
[ 4.168243] Initializing XFRM netlink socket
[ 4.174133] NET: Registered protocol family 10
[ 4.183166] IPv6 over IPv4 tunneling driver
[ 4.191558] NET: Registered protocol family 17
[ 4.196899] NET: Registered protocol family 15
[ 4.202239] Registering the dns_resolver key type
[ 4.208221] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 4.217834] ThumbEE CPU extension supported.
[ 4.240325] sr_init: No PMIC hook to init smartreflex
[ 4.246551] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
[ 4.255767] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
[ 4.313140] clock: disabling unused clocks to save power
[ 4.325317] fbcvt: 1024x768@60: CVT Name - .786M3-R
[ 4.366180] Console: switching to colour frame buffer device 128x48
[ 4.398468] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 4.411071] regulator_init_complete: VDAC: incomplete constraints, leaving on
[ 4.419708] regulator_init_complete: vads7846: incomplete constraints, leaving on
[ 4.429199] mmc0: new high speed SDHC card at address b368
[ 4.444671] input: gpio-keys as /devices/platform/gpio-keys/input/input1
[ 4.454162] mmcblk0: mmc0:b368 00000 7.51 GiB
[ 4.474731] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:13 UTC (946684813)
[ 4.483825] mmcblk0: p1 p2
[ 4.496887] Freeing init memory: 356K
[ 4.821258] udevd[725]: starting version 175
[ 6.060028] hub 1-0:1.0: hub_suspend
[ 6.060760] usb usb1: bus auto-suspend, wakeup 1
[ 6.060791] ehci-omap ehci-omap.0: suspend root hub
[ 6.061065] hub 2-0:1.0: hub_suspend
[ 6.061370] usb usb2: bus auto-suspend, wakeup 1
[ 6.661224] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 6.668884] kjournald starting. Commit interval 5 seconds
[ 8.080444] init: ureadahead main process (823) terminated with status 5
[ 9.746307] udevd[874]: starting version 175
[ 10.641235] EXT3-fs (mmcblk0p2): using internal journal
[ 12.128143] ads7846 spi1.0: touchscreen, irq 274
[ 12.154937] ads7846 spi1.0: no device detected, test read result was 0x00000FFF
[ 18.517059] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xe0888000, IRQ: 336
[ 19.255126] eth0: IPv6 duplicate address fe80::215:c9ff:fe28:f472 detected!
[ 20.136383] Bluetooth: Core ver 2.16
[ 20.142425] NET: Registered protocol family 31
[ 20.142456] Bluetooth: HCI device and connection manager initialized
[ 20.143066] Bluetooth: HCI socket layer initialized
[ 20.143127] Bluetooth: L2CAP socket layer initialized
[ 20.151824] Bluetooth: SCO socket layer initialized
[ 21.517089] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 21.517120] Bluetooth: BNEP filters: protocol multicast
[ 25.243103] Bluetooth: RFCOMM TTY layer initialized
[ 25.243194] Bluetooth: RFCOMM socket layer initialized
[ 25.243225] Bluetooth: RFCOMM ver 1.11
[ 27.869201] init: failsafe main process (1112) killed by TERM signal
[ 44.317474] init: tty1 main process (1289) killed by TERM signal
[ 44.561584] ADDRCONF(NETDEV_UP): usb0: link is not ready