dmesg - CPU_K10N78-1394_Athlon-5050e
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.1.10-1.16-desktop (geeko@buildhost) (gcc version 4.6.2 (SUSE Linux) ) #1 SMP PREEMPT Wed Jun 27 05:21:40 UTC 2012 (d016078)
Command line: root=/dev/disk/by-id/ata-ST3500320AS_9QM88P5Z-part1 resume=/dev/disk/by-id/ata-ST3500320AS_9QM88P5Z-part5 vga=0x346
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000cff90000 (usable)
BIOS-e820: 00000000cff90000 - 00000000cffa0000 (ACPI data)
BIOS-e820: 00000000cffa0000 - 00000000cffe0000 (ACPI NVS)
BIOS-e820: 00000000cffe0000 - 00000000d0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
NX (Execute Disable) protection: active
DMI present.
DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./K10N78-1394, BIOS P1.60 07/12/2010
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x130000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-EFFFF uncachable
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 0000000000 mask FF80000000 write-back
1 base 0080000000 mask FFC0000000 write-back
2 base 00C0000000 mask FFF0000000 write-back
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
TOM2: 0000000130000000 aka 4864M
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000d0000000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xcff90 max_arch_pfn = 0x400000000
found SMP MP-table at [ffff8800000ff780] ff780
initial memory mapped : 0 - 20000000
Base memory trampoline at [ffff88000009a000] 9a000 size 20480
init_memory_mapping: 0000000000000000-00000000cff90000
0000000000 - 00cfe00000 page 2M
00cfe00000 - 00cff90000 page 4k
kernel direct mapping tables up to cff90000 @ 1fffa000-20000000
init_memory_mapping: 0000000100000000-0000000130000000
0100000000 - 0130000000 page 2M
kernel direct mapping tables up to 130000000 @ cff8a000-cff90000
RAMDISK: 374b4000 - 37ff0000
ACPI: RSDP 00000000000fb9c0 00014 (v00 ACPIAM)
ACPI: RSDT 00000000cff90000 00048 (v01 071210 RSDT1448 20100712 MSFT 00000097)
ACPI: FACP 00000000cff90200 00084 (v01 A_M_I OEMFACP 12000601 MSFT 00000097)
ACPI: DSDT 00000000cff90460 087D9 (v01 ASR88 ASR88154 00000154 INTL 20051117)
ACPI: FACS 00000000cffa0000 00040
ACPI: APIC 00000000cff90390 00090 (v01 071210 APIC1448 20100712 MSFT 00000097)
ACPI: MCFG 00000000cff90420 0003C (v01 071210 OEMMCFG 20100712 MSFT 00000097)
ACPI: OEMB 00000000cffa0040 00073 (v01 071210 OEMB1448 20100712 MSFT 00000097)
ACPI: SRAT 00000000cff98c40 000C8 (v03 AMD FAM_F_10 00000002 AMD 00000001)
ACPI: AAFT 00000000cff98d10 00027 (v01 071210 OEMAAFT 20100712 MSFT 00000097)
ACPI: INFO 00000000cffa00c0 00124 (v01 071210 AMDINFO 20100712 MSFT 00000097)
ACPI: NVHD 00000000cffa01f0 00284 (v01 071210 NVHDCP 20100712 MSFT 00000097)
ACPI: SSDT 00000000cff98d40 0028A (v01 A M I POWERNOW 00000001 AMD 00000001)
ACPI: Local APIC address 0xfee00000
SRAT: PXM 0 -> APIC 0x00 -> Node 0
SRAT: PXM 0 -> APIC 0x01 -> Node 0
SRAT: Node 0 PXM 0 0-a0000
SRAT: Node 0 PXM 0 100000-d0000000
SRAT: Node 0 PXM 0 100000000-130000000
NUMA: Node 0 [0,a0000) + [100000,d0000000) -> [0,d0000000)
NUMA: Node 0 [0,d0000000) + [100000000,130000000) -> [0,130000000)
Initmem setup node 0 0000000000000000-0000000130000000
NODE_DATA [000000012ffec000 - 000000012fffffff]
[ffffea0000000000-ffffea00043fffff] PMD -> [ffff88012b600000-ffff88012effffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00130000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x000cff90
0: 0x00100000 -> 0x00130000
On node 0 totalpages: 1048351
DMA zone: 56 pages used for memmap
DMA zone: 5 pages reserved
DMA zone: 3922 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 833480 pages, LIFO batch:31
Normal zone: 2688 pages used for memmap
Normal zone: 193920 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x2008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 6 CPUs, 4 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
PM: Registered nosave memory: 00000000cff90000 - 00000000cffa0000
PM: Registered nosave memory: 00000000cffa0000 - 00000000cffe0000
PM: Registered nosave memory: 00000000cffe0000 - 00000000d0000000
PM: Registered nosave memory: 00000000d0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fef00000
PM: Registered nosave memory: 00000000fef00000 - 00000000fff00000
PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
Allocating PCI resources starting at d0000000 (gap: d0000000:2ec00000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:6 nr_node_ids:1
PERCPU: Embedded 27 pages/cpu @ffff88012fc00000 s78208 r8192 d24192 u262144
pcpu-alloc: s78208 r8192 d24192 u262144 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 4 5 - -
Built 1 zonelists in Node order, mobility grouping on. Total pages: 1031322
Policy zone: Normal
Kernel command line: root=/dev/disk/by-id/ata-ST3500320AS_9QM88P5Z-part1 resume=/dev/disk/by-id/ata-ST3500320AS_9QM88P5Z-part5 vga=0x346
PID hash table entries: 4096 (order: 3, 32768 bytes)
Checking aperture...
No AGP bridge found
Node 0: aperture @ 7840000000 size 32 MB
Aperture beyond 4GB. Ignoring.
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ c4000000
PM: Registered nosave memory: 00000000c4000000 - 00000000c8000000
Memory: 3973796k/4980736k available (5807k kernel code, 787332k absent, 219608k reserved, 7761k data, 940k init)
Preemptible hierarchical RCU implementation.
NR_IRQS:33024 nr_irqs:728 16
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
console [tty0] enabled
allocated 33554432 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Fast TSC calibration using PIT
Detected 2599.581 MHz processor.
Marking TSC unstable due to TSCs unsynchronized
Calibrating delay loop (skipped), value calculated using timer frequency.. 5199.16 BogoMIPS (lpj=2599581)
pid_max: default: 32768 minimum: 301
Security Framework initialized
AppArmor: AppArmor initialized
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
tseg: 0000000000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
using AMD E400 aware idle routine
ACPI: Core revision 20110623
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) Dual Core Processor 5050e stepping 02
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 9a000
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 2 CPUs
Total of 2 processors activated (10398.44 BogoMIPS).
devtmpfs: initialized
PM: Registering ACPI NVS region at cffa0000 (262144 bytes)
print_constraints: dummy:
RTC time: 10:27:31, date: 10/12/12
NET: Registered protocol family 16
node 0 link 0: io port [1000, ffffff]
TOM: 00000000d0000000 aka 3328M
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [d0000000, dfffffff]
node 0 link 0: mmio [f0000000, fe0bffff]
node 0 link 0: mmio [a0000, bffff]
TOM2: 0000000130000000 aka 4864M
bus: [00, 07] on node 0 link 0
bus: 00 index 0 [io 0x0000-0xffff]
bus: 00 index 1 [mem 0xd0000000-0xffffffff]
bus: 00 index 2 [mem 0x000a0000-0x000bffff]
bus: 00 index 3 [mem 0x130000000-0xfcffffffff]
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
ACPI: No dock devices found.
HEST: Table not found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff]
pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xdfffffff]
pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
pci 0000:00:00.0: [10de:0754] type 0 class 0x000500
pci 0000:00:01.0: [10de:075c] type 0 class 0x000601
pci 0000:00:01.0: reg 10: [io 0x2f00-0x2fff]
pci 0000:00:01.1: [10de:0752] type 0 class 0x000c05
pci 0000:00:01.1: reg 10: [io 0x2900-0x293f]
pci 0000:00:01.1: reg 20: [io 0x2d00-0x2d3f]
pci 0000:00:01.1: reg 24: [io 0x2e00-0x2e3f]
pci 0000:00:01.1: PME# supported from D3hot D3cold
pci 0000:00:01.1: PME# disabled
pci 0000:00:01.2: [10de:0751] type 0 class 0x000500
pci 0000:00:01.3: [10de:0753] type 0 class 0x000b40
pci 0000:00:01.3: reg 10: [mem 0xf4f80000-0xf4ffffff]
pci 0000:00:01.4: [10de:0568] type 0 class 0x000500
pci 0000:00:02.0: [10de:077b] type 0 class 0x000c03
pci 0000:00:02.0: reg 10: [mem 0xf4f7f000-0xf4f7ffff]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: [10de:077c] type 0 class 0x000c03
pci 0000:00:02.1: reg 10: [mem 0xf4f7ec00-0xf4f7ecff]
pci 0000:00:02.1: supports D1 D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
pci 0000:00:04.0: [10de:077d] type 0 class 0x000c03
pci 0000:00:04.0: reg 10: [mem 0xf4f7d000-0xf4f7dfff]
pci 0000:00:04.0: supports D1 D2
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:04.1: [10de:077e] type 0 class 0x000c03
pci 0000:00:04.1: reg 10: [mem 0xf4f7e800-0xf4f7e8ff]
pci 0000:00:04.1: supports D1 D2
pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.1: PME# disabled
pci 0000:00:06.0: [10de:0759] type 0 class 0x000101
pci 0000:00:06.0: reg 20: [io 0xffa0-0xffaf]
pci 0000:00:07.0: [10de:0774] type 0 class 0x000403
pci 0000:00:07.0: reg 10: [mem 0xf4f78000-0xf4f7bfff]
pci 0000:00:07.0: PME# supported from D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:08.0: [10de:075a] type 1 class 0x000604
pci 0000:00:09.0: [10de:0ad0] type 0 class 0x000101
pci 0000:00:09.0: reg 10: [io 0xc480-0xc487]
pci 0000:00:09.0: reg 14: [io 0xc400-0xc403]
pci 0000:00:09.0: reg 18: [io 0xc080-0xc087]
pci 0000:00:09.0: reg 1c: [io 0xc000-0xc003]
pci 0000:00:09.0: reg 20: [io 0xbc00-0xbc0f]
pci 0000:00:09.0: reg 24: [mem 0xf4f76000-0xf4f77fff]
pci 0000:00:0a.0: [10de:0760] type 0 class 0x000200
pci 0000:00:0a.0: reg 10: [mem 0xf4f7c000-0xf4f7cfff]
pci 0000:00:0a.0: reg 14: [io 0xb880-0xb887]
pci 0000:00:0a.0: reg 18: [mem 0xf4f7e400-0xf4f7e4ff]
pci 0000:00:0a.0: reg 1c: [mem 0xf4f7e000-0xf4f7e00f]
pci 0000:00:0a.0: supports D1 D2
pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0a.0: PME# disabled
pci 0000:00:10.0: [10de:0778] type 1 class 0x000604
pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.0: PME# disabled
pci 0000:00:12.0: [10de:075b] type 1 class 0x000604
pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:12.0: PME# disabled
pci 0000:00:13.0: [10de:077a] type 1 class 0x000604
pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:13.0: PME# disabled
pci 0000:00:14.0: [10de:077a] type 1 class 0x000604
pci 0000:00:14.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:14.0: PME# disabled
pci 0000:00:18.0: [1022:1100] type 0 class 0x000600
pci 0000:00:18.1: [1022:1101] type 0 class 0x000600
pci 0000:00:18.2: [1022:1102] type 0 class 0x000600
pci 0000:00:18.3: [1022:1103] type 0 class 0x000600
pci 0000:01:08.0: [1106:3044] type 0 class 0x000c00
pci 0000:01:08.0: reg 10: [mem 0xf9fff800-0xf9ffffff]
pci 0000:01:08.0: reg 14: [io 0xdc00-0xdc7f]
pci 0000:01:08.0: supports D2
pci 0000:01:08.0: PME# supported from D2 D3hot D3cold
pci 0000:01:08.0: PME# disabled
pci 0000:01:09.0: [14f1:8800] type 0 class 0x000400
pci 0000:01:09.0: reg 10: [mem 0xf8000000-0xf8ffffff]
pci 0000:01:09.1: [14f1:8811] type 0 class 0x000480
pci 0000:01:09.1: reg 10: [mem 0xf7000000-0xf7ffffff]
pci 0000:01:09.2: [14f1:8802] type 0 class 0x000480
pci 0000:01:09.2: reg 10: [mem 0xf6000000-0xf6ffffff]
pci 0000:01:09.4: [14f1:8804] type 0 class 0x000480
pci 0000:01:09.4: reg 10: [mem 0xf5000000-0xf5ffffff]
pci 0000:01:0a.0: [1131:5402] type 0 class 0x000480
pci 0000:01:0a.0: reg 10: [mem 0xf9000000-0xf97fffff]
pci 0000:01:0a.0: reg 14: [mem 0xf9c00000-0xf9dfffff]
pci 0000:00:08.0: PCI bridge to [bus 01-01] (subtractive decode)
pci 0000:00:08.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:08.0: bridge window [mem 0xf5000000-0xf9ffffff]
pci 0000:00:08.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:08.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:08.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:08.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
pci 0000:00:08.0: bridge window [mem 0xd0000000-0xdfffffff] (subtractive decode)
pci 0000:00:08.0: bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode)
pci 0000:02:00.0: [10de:0605] type 0 class 0x000300
pci 0000:02:00.0: reg 10: [mem 0xfd000000-0xfdffffff]
pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:02:00.0: reg 1c: [mem 0xfa000000-0xfbffffff 64bit]
pci 0000:02:00.0: reg 24: [io 0xec00-0xec7f]
pci 0000:02:00.0: reg 30: [mem 0xfebe0000-0xfebfffff pref]
pci 0000:00:10.0: PCI bridge to [bus 02-02]
pci 0000:00:10.0: bridge window [io 0xe000-0xefff]
pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfebfffff]
pci 0000:00:10.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:12.0: PCI bridge to [bus 03-03]
pci 0000:00:12.0: bridge window [mem 0xf3d00000-0xf3dfffff 64bit pref]
pci 0000:00:13.0: PCI bridge to [bus 04-04]
pci 0000:00:13.0: bridge window [mem 0xf3e00000-0xf3efffff 64bit pref]
pci 0000:00:14.0: PCI bridge to [bus 05-05]
pci 0000:00:14.0: bridge window [mem 0xf3f00000-0xf3ffffff 64bit pref]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR14._PRT]
pci0000:00: Requesting ACPI _OSC control (0x1d)
pci0000:00: ACPI _OSC request failed (AE_SUPPORT), returned control mask: 0x0c
ACPI _OSC control for PCIe not granted, disabling ASPM
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *15
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN0A] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LN0B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN0C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN0D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN1A] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN1B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN1C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN1D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN2A] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LN2B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN2C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN2D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN3A] (IRQs 16 17 18 19) *15
ACPI: PCI Interrupt Link [LN3B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN3C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN3D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN4A] (IRQs 16 17 18 19) *7
ACPI: PCI Interrupt Link [LN4B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN4C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN4D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN5A] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN5B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN5C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN5D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN6A] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN6B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN6C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN6D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN7A] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN7B] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN7C] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LN7D] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *15
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *15
ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *11
vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:02:00.0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff
reserve RAM buffer: 00000000cff90000 - 00000000cfffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-ff]
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: [io 0x0000-0x0cf7 window]
pnp 00:00: [io 0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000d0000-0x000dffff window]
pnp 00:00: [mem 0xd0000000-0xdfffffff window]
pnp 00:00: [mem 0xf0000000-0xfebfffff window]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: [dma 4]
pnp 00:01: [io 0x0000-0x000f]
pnp 00:01: [io 0x0081-0x0083]
pnp 00:01: [io 0x0087]
pnp 00:01: [io 0x0089-0x008b]
pnp 00:01: [io 0x008f]
pnp 00:01: [io 0x00c0-0x00df]
pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:02: [io 0x0061]
pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:03: [io 0x00f0-0x00ff]
pnp 00:03: [irq 13]
pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:04: [io 0x03f0-0x03f5]
pnp 00:04: [io 0x03f7]
pnp 00:04: [irq 6]
pnp 00:04: [dma 2]
pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
pnp 00:05: [mem 0x000d0000-0x000d3fff window]
pnp 00:05: [mem 0x000d4000-0x000d7fff window]
pnp 00:05: [mem 0x000de000-0x000dffff window]
pnp 00:05: [io 0x0010-0x001f]
pnp 00:05: [io 0x0022-0x003f]
pnp 00:05: [io 0x0044-0x004d]
pnp 00:05: [io 0x0050-0x005f]
pnp 00:05: [io 0x0062-0x0063]
pnp 00:05: [io 0x0065-0x006f]
pnp 00:05: [io 0x0072-0x007f]
pnp 00:05: [io 0x0080]
pnp 00:05: [io 0x0084-0x0086]
pnp 00:05: [io 0x0088]
pnp 00:05: [io 0x008c-0x008e]
pnp 00:05: [io 0x0090-0x009f]
pnp 00:05: [io 0x00a2-0x00bf]
pnp 00:05: [io 0x00e0-0x00ef]
pnp 00:05: [io 0x04d0-0x04d1]
pnp 00:05: [io 0x0800-0x080f]
pnp 00:05: [io 0x2000-0x207f]
pnp 00:05: [io 0x2080-0x20ff]
pnp 00:05: [io 0x2400-0x247f]
pnp 00:05: [io 0x2480-0x24ff]
pnp 00:05: [io 0x2800-0x287f]
pnp 00:05: [io 0x2880-0x28ff]
pnp 00:05: [mem 0x00000000-0xffffffffffffffff disabled]
pnp 00:05: [mem 0x00000000-0xffffffffffffffff disabled]
pnp 00:05: [mem 0xfed04000-0xfed04fff]
pnp 00:05: [mem 0xfee01000-0xfeefffff]
system 00:05: [io 0x04d0-0x04d1] has been reserved
system 00:05: [io 0x0800-0x080f] has been reserved
system 00:05: [io 0x2000-0x207f] has been reserved
system 00:05: [io 0x2080-0x20ff] has been reserved
system 00:05: [io 0x2400-0x247f] has been reserved
system 00:05: [io 0x2480-0x24ff] has been reserved
system 00:05: [io 0x2800-0x287f] has been reserved
system 00:05: [io 0x2880-0x28ff] has been reserved
system 00:05: [mem 0x000d0000-0x000d3fff window] has been reserved
system 00:05: [mem 0x000d4000-0x000d7fff window] has been reserved
system 00:05: [mem 0x000de000-0x000dffff window] has been reserved
system 00:05: [mem 0xfed04000-0xfed04fff] has been reserved
system 00:05: [mem 0xfee01000-0xfeefffff] has been reserved
system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:06: [io 0x0070-0x0071]
pnp 00:06: [irq 8]
pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:07: [mem 0xfec00000-0xfec00fff]
pnp 00:07: [mem 0xfee00000-0xfee00fff]
system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:08: [io 0x0060]
pnp 00:08: [io 0x0064]
pnp 00:08: [irq 1]
pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
pnp 00:09: [io 0x03f8-0x03ff]
pnp 00:09: [irq 4]
pnp 00:09: [dma 0 disabled]
pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled]
pnp 00:0a: [io 0x0290-0x029f]
system 00:0a: [io 0x0290-0x029f] has been reserved
system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0b: [mem 0xe0000000-0xefffffff]
system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0c: [mem 0x00000000-0x0009ffff]
pnp 00:0c: [mem 0x000c0000-0x000cffff]
pnp 00:0c: [mem 0x000e0000-0x000fffff]
pnp 00:0c: [mem 0x00100000-0xcfffffff]
pnp 00:0c: [mem 0xfec00000-0xffffffff]
system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0c: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0c: [mem 0x00100000-0xcfffffff] could not be reserved
system 00:0c: [mem 0xfec00000-0xffffffff] could not be reserved
system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
Switching to clocksource acpi_pm
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:08.0: PCI bridge to [bus 01-01]
pci 0000:00:08.0: bridge window [io 0xd000-0xdfff]
pci 0000:00:08.0: bridge window [mem 0xf5000000-0xf9ffffff]
pci 0000:00:10.0: PCI bridge to [bus 02-02]
pci 0000:00:10.0: bridge window [io 0xe000-0xefff]
pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfebfffff]
pci 0000:00:10.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:12.0: PCI bridge to [bus 03-03]
pci 0000:00:12.0: bridge window [mem 0xf3d00000-0xf3dfffff 64bit pref]
pci 0000:00:13.0: PCI bridge to [bus 04-04]
pci 0000:00:13.0: bridge window [mem 0xf3e00000-0xf3efffff 64bit pref]
pci 0000:00:14.0: PCI bridge to [bus 05-05]
pci 0000:00:14.0: bridge window [mem 0xf3f00000-0xf3ffffff 64bit pref]
pci 0000:00:08.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LN0A] enabled at IRQ 19
pci 0000:00:10.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:10.0: setting latency timer to 64
Switched to NOHz mode on CPU #0
ACPI: PCI Interrupt Link [LN2A] enabled at IRQ 18
pci 0000:00:12.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18
Switched to NOHz mode on CPU #1
pci 0000:00:12.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LN3A] enabled at IRQ 17
pci 0000:00:13.0: PCI INT A -> Link[LN3A] -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:13.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LN4A] enabled at IRQ 16
pci 0000:00:14.0: PCI INT A -> Link[LN4A] -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:14.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0xd0000000-0xdfffffff]
pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff]
pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:01: resource 1 [mem 0xf5000000-0xf9ffffff]
pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:01: resource 8 [mem 0xd0000000-0xdfffffff]
pci_bus 0000:01: resource 9 [mem 0xf0000000-0xfebfffff]
pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
pci_bus 0000:02: resource 1 [mem 0xfa000000-0xfebfffff]
pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
pci_bus 0000:03: resource 2 [mem 0xf3d00000-0xf3dfffff 64bit pref]
pci_bus 0000:04: resource 2 [mem 0xf3e00000-0xf3efffff 64bit pref]
pci_bus 0000:05: resource 2 [mem 0xf3f00000-0xf3ffffff 64bit pref]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
pci 0000:00:07.0: Enabling HT MSI Mapping
pci 0000:00:08.0: Enabling HT MSI Mapping
pci 0000:00:09.0: Enabling HT MSI Mapping
pci 0000:00:0a.0: Enabling HT MSI Mapping
pci 0000:02:00.0: Boot video device
PCI: CLS 64 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 11504k freed
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ c4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
audit: initializing netlink socket (disabled)
type=2000 audit(1350037651.590:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 7912
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: mode is 1600x1200x16, linelength=3200, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
vesafb: framebuffer at 0xfb000000, mapped to 0xffffc90011100000, using 7500k, total 14336k
bootsplash 3.2.0-2010/03/31: looking for picture...
bootsplash: silentjpeg size 114278 bytes
bootsplash: ...found (1600x1200, 42321 bytes, v3).
Console: switching to colour frame buffer device 196x71
fb0: VESA VGA frame buffer device
ERST: Table is not found!
GHES: HEST is not enabled!
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
ahci 0000:00:09.0: version 3.0
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
ahci 0000:00:09.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
ahci 0000:00:09.0: irq 40 for MSI/MSI-X
ahci 0000:00:09.0: controller can't do PMP, turning off CAP_PMP
ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl IDE mode
ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pio sxs boh
ahci 0000:00:09.0: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m8192@0xf4f76000 port 0xf4f76100 irq 40
ata2: SATA max UDMA/133 abar m8192@0xf4f76000 port 0xf4f76180 irq 40
ata3: SATA max UDMA/133 abar m8192@0xf4f76000 port 0xf4f76200 irq 40
ata4: SATA max UDMA/133 abar m8192@0xf4f76000 port 0xf4f76280 irq 40
ata5: SATA max UDMA/133 abar m8192@0xf4f76000 port 0xf4f76300 irq 40
ata6: SATA max UDMA/133 abar m8192@0xf4f76000 port 0xf4f76380 irq 40
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 22, io mem 0xf4f7ec00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.1.10-1.16-desktop ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI Interrupt Link [UB12] enabled at IRQ 21
ehci_hcd 0000:00:04.1: PCI INT B -> Link[UB12] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:04.1: setting latency timer to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: debug port 1
ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
ehci_hcd 0000:00:04.1: irq 21, io mem 0xf4f7e800
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 3.1.10-1.16-desktop ehci_hcd
usb usb2: SerialNumber: 0000:00:04.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 20
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.0: irq 20, io mem 0xf4f7f000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 3.1.10-1.16-desktop ohci_hcd
usb usb3: SerialNumber: 0000:00:02.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
ACPI: PCI Interrupt Link [UB11] enabled at IRQ 23
ohci_hcd 0000:00:04.0: PCI INT A -> Link[UB11] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:04.0: setting latency timer to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:04.0: irq 23, io mem 0xf4f7d000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 3.1.10-1.16-desktop ohci_hcd
usb usb4: SerialNumber: 0000:00:04.0
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
TCP cubic registered
NET: Registered protocol family 10
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
Registering the dns_resolver key type
libceph: loaded (mon/osd proto 15/24, osdmap 5/6 5/6)
PM: Checking hibernation image partition /dev/disk/by-id/ata-ST3500320AS_9QM88P5Z-part5
ata2: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata3.00: ATAPI: TSSTcorp CDDVDW SH-S223Q, SB03, max UDMA/100
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata1.00: ATA-8: ST3500320AS, SD1A, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3500320AS SD1A PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223Q SB03 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 >
sd 0:0:0:0: [sda] Attached SCSI disk
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
Magic number: 0:910:476
rtc_cmos 00:06: setting system clock to 2012-10-12 10:27:32 UTC (1350037652)
Freeing unused kernel memory: 940k freed
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 320k freed
Freeing unused kernel memory: 2012k freed
usb 3-2: new low speed USB device number 2 using ohci_hcd
pata_amd 0000:00:06.0: version 0.4.1
pata_amd 0000:00:06.0: setting latency timer to 64
scsi6 : pata_amd
scsi7 : pata_amd
ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
usb 3-2: New USB device found, idVendor=046d, idProduct=c00e
usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-2: Product: USB-PS/2 Optical Mouse
usb 3-2: Manufacturer: Logitech
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input1
generic-usb 0003:046D:C00E.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-2/input0
ata7.00: ATA-7: ST3320620A, 3.AAD, max UDMA/100
ata7.00: 625142448 sectors, multi 16: LBA48
ata7.01: ATAPI: IDE DVD-ROM 16X, VER 2.91, max UDMA/33
ata7: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6c00000) ACPI=0x3f01f (20:60:0x15)
ata7: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc6c00000) ACPI=0x701f (20:60:0x15)
ata7.00: configured for UDMA/100
ata7.01: configured for UDMA/33
scsi 6:0:0:0: Direct-Access ATA ST3320620A 3.AA PQ: 0 ANSI: 5
sd 6:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
scsi 6:0:1:0: CD-ROM IDE DVD-ROM 16X 2.91 PQ: 0 ANSI: 5
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata8: port disabled--ignoring
sdb: sdb1 sdb2 < sdb5 >
sd 6:0:0:0: [sdb] Attached SCSI disk
ACPI: acpi_idle registered with cpuidle
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
udevd[139]: starting version 173
PM: Marking nosave pages: 000000000009f000 - 0000000000100000
PM: Marking nosave pages: 00000000cff90000 - 0000000100000000
PM: Marking nosave pages: 00000000c4000000 - 00000000c8000000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
PM: Starting manual resume from disk
PM: Hibernation image partition 8:5 present
PM: Looking for hibernation image.
PM: Image not found (code -22)
PM: Hibernation image not present or could not be loaded.
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda1): using internal journal
EXT3-fs (sda1): mounted filesystem with ordered data mode
systemd[1]: systemd 37 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +SYSVINIT +LIBCRYPTSETUP; suse)
systemd[1]: Set hostname to .
systemd[1]: [/etc/init.d/cups:19] Failed to add LSB Provides name cupsd.service, ignoring: File exists
udevd[422]: starting version 173
systemd-readahead-replay[394]: Bumped block_nr parameter of 8:0 to 16384. This is a temporary hack and should be removed one day.
boot.localnet[425]: Using boot-specified hostname 'linux01.home'
boot.localnet[425]: Setting up hostname 'linux01'..done
boot.localnet[425]: Setting up loopback interface RTNETLINK answers: File exists
boot.localnet[425]: ..done
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 2:0:0:0: Attached scsi generic sg1 type 5
sd 6:0:0:0: Attached scsi generic sg2 type 0
scsi 6:0:1:0: Attached scsi generic sg3 type 5
sr0: scsi3-mmc drive: 32x/48x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
sr 6:0:1:0: Attached scsi CD-ROM sr1
k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
MCE: In-kernel MCE decoding enabled.
lomoco[543]: 003.002: 046d:c00e Wheel Mouse Optical (M-BJ58) Caps: RES
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: PC Speaker as /devices/platform/pcspkr/input/input2
EDAC MC: Ver: 2.1.0
i2c i2c-0: nForce2 SMBus adapter at 0x2d00
ACPI: resource nForce2_smbus [io 0x2e00-0x2e3f] conflicts with ACPI region SM00 [io 0x2e00-0x2e3f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
ACPI: Power Button [PWRF]
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 22 (level, low) -> IRQ 22
forcedeth 0000:00:0a.0: setting latency timer to 64
forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:19:66:8c:ac:56
forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim msi desc-v3
AMD64 EDAC driver v3.4.0
EDAC amd64: DRAM ECC disabled.
EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
wmi: Mapper loaded
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
firewire_ohci 0000:01:08.0: PCI INT A -> Link[LNKA] -> GSI 19 (level, low) -> IRQ 19
firewire_ohci: Added fw-ohci device 0000:01:08.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x11
ifup[687]: Service network not started and mode 'auto' -> skipping
firewire_core: created device fw0: GUID 008f130055e20500, S400
Linux video capture interface: v2.00
snd_hda_intel 0000:00:07.0: power state changed by ACPI to D0
snd_hda_intel 0000:00:07.0: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
snd_hda_intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
hda_intel: msi for device 1849:0888 set to 0
hda_intel: position_fix set to 1 for device 1849:0888
snd_hda_intel 0000:00:07.0: setting latency timer to 64
ALSA hda_intel.c:1454 Enable delay in RIRB handling
cx2388x alsa driver version 0.0.9 loaded
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.9 loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
cx88_audio 0000:01:09.1: PCI INT A -> Link[LNKB] -> GSI 18 (level, low) -> IRQ 18
cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected], frontend(s): 1
cx88[0]: TV tuner type -1, Radio tuner type -1
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
cx88/0: cx2388x v4l2 driver version 0.0.9 loaded
hda_codec: ALC888: BIOS auto-probing.
hda_codec: ALC888: SKU not ready 0x411111f0
ALSA hda_codec.c:4895 autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
ALSA hda_codec.c:4899 speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA hda_codec.c:4903 hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
ALSA hda_codec.c:4904 mono: mono_out=0x0
ALSA hda_codec.c:4907 dig-out=0x1e/0x0
ALSA hda_codec.c:4908 inputs:
ALSA hda_codec.c:4912 Rear Mic=0x18
ALSA hda_codec.c:4912 Front Mic=0x19
ALSA hda_codec.c:4912 Line=0x1a
ALSA hda_codec.c:4912 CD=0x1c
ALSA hda_codec.c:4914
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
ALSA patch_realtek.c:1291 realtek: No valid SSID, checking pincfg 0x411111f0 for NID 0x1d
ALSA patch_realtek.c:1374 realtek: Enable default setup for auto mode as fallback
i2c-core: driver [tuner] using legacy suspend method
i2c-core: driver [tuner] using legacy resume method
IR Sony protocol handler initialized
tveeprom 1-0050: Hauppauge model 69100, rev B2C3, serial# 5308612
tveeprom 1-0050: MAC address is 00:0d:fe:51:00:c4
tveeprom 1-0050: tuner model is Conexant CX24118A (idx 123, type 4)
IR MCE Keyboard/mouse protocol handler initialized
tveeprom 1-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 1-0050: audio processor is None (idx 0)
tveeprom 1-0050: decoder processor is CX882 (idx 25)
tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=69100
input: HDA NVidia Headphone as /devices/pci0000:00/0000:00:07.0/sound/card0/input5
lirc_dev: IR Remote Control driver registered, major 250
IR LIRC bridge handler initialized
Registered IR keymap rc-hauppauge
input: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:08.0/0000:01:09.1/rc/rc0/input6
rc0: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:08.0/0000:01:09.1/rc/rc0
input: MCE IR Keyboard/Mouse (cx88xx) as /devices/virtual/input/input7
rc rc0: lirc_dev: driver ir-lirc-codec (cx88xx) registered at minor = 0
cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:09.2: PCI INT A -> Link[LNKB] -> GSI 18 (level, low) -> IRQ 18
cx88[0]/2: found at 0000:01:09.2, rev: 5, irq: 18, latency: 32, mmio: 0xf6000000
cx8800 0000:01:09.0: PCI INT A -> Link[LNKB] -> GSI 18 (level, low) -> IRQ 18
cx88[0]/0: found at 0000:01:09.0, rev: 5, irq: 18, latency: 32, mmio: 0xf8000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:07.0/input/input8
systemd-fsck[792]: Backup: sauber, 506638/18882560 Dateien, 70815847/75519549 Blöcke
kjournald starting. Commit interval 5 seconds
EXT3-fs (sdb5): using internal journal
EXT3-fs (sdb5): mounted filesystem with ordered data mode
Adding 4192928k swap on /dev/sda5. Priority:0 extents:1 across:4192928k
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
systemd-fsck[804]: Home: sauber, 95178/655360 Dateien, 1660541/2620595 Blöcke
nvidia 0000:02:00.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19
nvidia 0000:02:00.0: setting latency timer to 64
vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.43 Sun Aug 19 20:14:03 PDT 2012
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda9): using internal journal
EXT3-fs (sda9): mounted filesystem with ordered data mode
cx88/2: cx2388x dvb driver version 0.0.9 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69]
cx88[0]/2: cx2388x based DVB/ATSC card
cx8802_alloc_frontends() allocating 1 frontend(s)
systemd-fsck[817]: Data: sauber, 123875/21094400 Dateien, 74972279/84353290 Blöcke
DVB: registering new adapter (cx88[0])
DVB: registering adapter 0 frontend 0 (Conexant CX24116/CX24118)...
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda12): using internal journal
EXT3-fs (sda12): mounted filesystem with ordered data mode
type=1400 audit(1350030473.182:2): apparmor="STATUS" operation="profile_load" name="/bin/ping" pid=894 comm="apparmor_parser"
type=1400 audit(1350030473.206:3): apparmor="STATUS" operation="profile_load" name="/sbin/klogd" pid=902 comm="apparmor_parser"
type=1400 audit(1350030473.519:4): apparmor="STATUS" operation="profile_load" name="/sbin/syslog-ng" pid=906 comm="apparmor_parser"
type=1400 audit(1350030473.686:5): apparmor="STATUS" operation="profile_load" name="/sbin/syslogd" pid=910 comm="apparmor_parser"
type=1400 audit(1350030473.719:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2" pid=915 comm="apparmor_parser"
type=1400 audit(1350030473.723:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2//DEFAULT_URI" pid=915 comm="apparmor_parser"
type=1400 audit(1350030473.728:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2//HANDLING_UNTRUSTED_INPUT" pid=915 comm="apparmor_parser"
type=1400 audit(1350030473.732:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2//phpsysinfo" pid=915 comm="apparmor_parser"
type=1400 audit(1350030473.913:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/dovecot/deliver" pid=919 comm="apparmor_parser"
type=1400 audit(1350030474.073:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/dovecot/dovecot-auth" pid=923 comm="apparmor_parser"
boot.apparmor[877]: Starting AppArmor ..done
irq_balancer[993]: Starting irqbalance ..done
powernow-k8: Found 1 AMD Athlon(tm) Dual Core Processor 5050e (2 cpu cores) (version 2.20.00)
powernow-k8: fid 0x12 (2600 MHz), vid 0xe
powernow-k8: fid 0x10 (2400 MHz), vid 0x10
powernow-k8: fid 0xe (2200 MHz), vid 0x12
powernow-k8: fid 0xc (2000 MHz), vid 0x14
powernow-k8: fid 0xa (1800 MHz), vid 0x16
powernow-k8: fid 0x2 (1000 MHz), vid 0x1a
cpufreq[1006]: Loading CPUFreq modules..done
lircd-0.8.7[1062]: lircd(devinput) ready, using /var/run/lirc/lircd
lirc[1014]: Starting lircd (/dev/input/ir)..done
saa7146: register extension 'av7110'.
systemd[1]: NetworkManager.service: control process exited, code=exited status=1
systemd[1]: Job NetworkManager-wait-online.service/start failed with result 'dependency'.
systemd[1]: Unit NetworkManager.service entered failed state.
ip6_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
forcedeth 0000:00:0a.0: irq 41 for MSI/MSI-X
NET: Registered protocol family 17
eth0: no IPv6 routers present
/dev/vmmon[3487]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[3487]: Module vmmon: initialized
[3519]: VMCI: shared components initialized.
[3519]: VMCI: host components initialized.
[3519]: VMCI: Module registered (name=vmci,major=10,minor=59).
[3519]: VMCI: Using host personality
[3519]: VMCI: Module (name=vmci) is initialized
fuse init (API version 7.17)
ppdev: user-space parallel port driver
/dev/vmnet: open called by PID 3771 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 3983 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 3986 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 4015 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 4020 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
userif-3: sent link down event.
userif-3: sent link up event.
/dev/vmnet: open called by PID 4027 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
vmnet8: no IPv6 routers present
vmnet1: no IPv6 routers present
NVRM: GPU at 0000:02:00: GPU-c805242d-df8c-baf1-465a-545010c505e3
NVRM: Your system is not currently configured to drive a VGA console
NVRM: on the primary VGA device. The NVIDIA Linux graphics driver
NVRM: requires the use of a text-mode VGA console. Use of other console
NVRM: drivers including, but not limited to, vesafb, may result in
NVRM: corruption and stability problems, and is not supported.