dmesg - flac_odroidc1
[ 0.000000@0] Booting Linux on physical CPU 0x200
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Linux version 3.10.42 (root@xu-b1) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-19ubuntu1) ) #1 SMP PREEMPT Sat Dec 20 00:23:41 BRST 2014
[ 0.000000@0] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d
[ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000@0] Machine: ODROIDC, model: AMLOGIC
[ 0.000000@0] physical memory start address is 0x200000
[ 0.000000@0] reserved_end is d9fffff
[ 0.000000@0]
[ 0.000000@0] Total memory is 1022 MiB
[ 0.000000@0] Reserved low memory from 0x06000000 to 0x0d9fffff, size: 122 MiB
[ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB)
[ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB)
[ 0.000000@0] mesonstream0(low) : 0x07a00000 - 0x09a00000 ( 32 MiB)
[ 0.000000@0] vdec0(low) : 0x09a00000 - 0x0da00000 ( 64 MiB)
[ 0.000000@0] ppmgr0(high) : 0x3f000000 - 0x40000000 ( 16 MiB)
[ 0.000000@0] cma: CMA: reserved 8 MiB at 3e800000
[ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000@0] On node 0 totalpages: 222720
[ 0.000000@0] free_area_init_node: node 0, pgdat c09c2840, node_mem_map c0cc9000
[ 0.000000@0] Normal zone: 1520 pages used for memmap
[ 0.000000@0] Normal zone: 0 pages reserved
[ 0.000000@0] Normal zone: 159744 pages, LIFO batch:31
[ 0.000000@0] HighMem zone: 492 pages used for memmap
[ 0.000000@0] HighMem zone: 62976 pages, LIFO batch:15
[ 0.000000@0] Meson chip version = RevA (1B:A - 0:B72)
[ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c14b1000 s8768 r8192 d15808 u32768
[ 0.000000@0] pcpu-alloc: s8768 r8192 d15808 u32768 alloc=8*4096
[ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 221200
[ 0.000000@0] cvbs trimming line = 0xa000
[ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
[ 0.000000@0] osd1:1
[ 0.000000@0] loaded:268435459
[ 0.000000@0] logo has been loaded
[ 0.000000@0] 720p:10
[ 0.000000@0] full:2
[ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
[ 0.000000@0] kernel get hdmimode form uboot is 720p
[ 0.000000@0] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000@0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000@0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000@0] Memory: 64MB 16MB 790MB = 870MB total
[ 0.000000@0] Memory: 858460k/858460k available, 32420k reserved, 243712K highmem
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000@0] .text : 0xc0008000 - 0xc090d364 (9237 kB)
[ 0.000000@0] .init : 0xc090e000 - 0xc0946240 ( 225 kB)
[ 0.000000@0] .data : 0xc0948000 - 0xc09c37a0 ( 494 kB)
[ 0.000000@0] .bss : 0xc09c37a0 - 0xc0cc450c (3076 kB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:256
[ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000@0] Global timer: MESON TIMER-F (c0966580) initialized
[ 0.000000@0] Switching to timer-based delay loop
[ 0.000000@0] Console: colour dummy device 80x30
[ 0.000000@0] meson_serial_console_setup
[ 0.000000@0] console [ttyS0] enabled
[ 0.311161@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.321451@0] pid_max: default: 32768 minimum: 301
[ 0.326349@0] Security Framework initialized
[ 0.330476@0] SELinux: Initializing.
[ 0.334102@0] SELinux: Starting in permissive mode
[ 0.334123@0] AppArmor: AppArmor disabled by boot time parameter
[ 0.340168@0] Mount-cache hash table entries: 512
[ 0.349109@0] Initializing cgroup subsys devices
[ 0.349421@0] CPU: Testing write buffer coherency: ok
[ 0.354787@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[ 0.360249@0] Setting up static identity map for 0xc0656ce8 - 0xc0656d40
[ 0.366887@0] L310 cache controller enabled
[ 0.370989@0] l2x0: 8 ways, 2048 sets, CACHE_ID 0x4100a0c9, Cache size: 524288 B
[ 0.378388@0] AUX_CTRL 0x7ec60001, PERFETCH_CTRL 0x75000007, POWER_CTRL 0x00000000
[ 0.386537@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
[ 0.470306@1] CPU1: Booted secondary processor
[ 0.470325@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[ 0.490299@2] CPU2: Booted secondary processor
[ 0.490316@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[ 0.510303@3] CPU3: Booted secondary processor
[ 0.510321@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[ 0.510414@0] Brought up 4 CPUs
[ 0.538592@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
[ 0.544818@0] CPU: All CPU(s) started in SVC mode.
[ 0.550338@0] devtmpfs: initialized
[ 0.559644@0] clkrate [ xtal ] : 24000000
[ 0.559677@0] clkrate [ pll_sys ] : 1200000000
[ 0.562635@0] clkrate [ pll_fixed ] : 2550000000
[ 0.567287@0] clkrate [ pll_vid ] : 732000000
[ 0.571714@0] clkrate [ pll_ddr ] : 0
[ 0.575427@0] clkrate [ a9_clk ] : 1200000000
[ 0.579842@0] clkrate [ clk81 ] : 159375000
[ 0.584540@0] pinctrl core: initialized pinctrl subsystem
[ 0.589708@0] regulator-dummy: no parameters
[ 0.594232@0] NET: Registered protocol family 16
[ 0.602523@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.606387@0] VPU driver version: v02
[ 0.609024@0] load vpu_clk in dts: 182150000Hz(3)
[ 0.613749@0] vpu_probe OK
[ 0.618736@0] amlogic_gpio gpio: Probed amlogic GPIO driver
[ 0.622141@0] register lm device lm-root
[ 0.625871@0] register lm device lm1
[ 0.629412@0] register lm device lm0
[ 0.633080@0] Init pinux probe!
[ 0.636718@0] pinmux-m8b pinmux: Probed amlogic pinctrl driver
[ 0.641884@0] tv_init_module
[ 0.644703@0] major number 254 for disp
[ 0.648505@0] vout_register_server
[ 0.651896@0] register tv module server ok
[ 0.690442@0] bio: create slab at 0
[ 0.691137@0] SCSI subsystem initialized
[ 0.693078@0] usbcore: registered new interface driver usbfs
[ 0.698561@0] usbcore: registered new interface driver hub
[ 0.704083@0] usbcore: registered new device driver usb
[ 0.709259@0] Linux video capture interface: v2.00
[ 0.714254@0] request vpu clk holdings: vencp 106250000Hz
[ 0.719299@0] TV mode 720p selected.
[ 0.722867@0] already display in uboot
[ 0.729967@0] Advanced Linux Sound Architecture Driver Initialized.
[ 0.733290@0] Bluetooth: Core ver 2.16
[ 0.736574@0] NET: Registered protocol family 31
[ 0.741141@0] Bluetooth: HCI device and connection manager initialized
[ 0.747630@0] Bluetooth: HCI socket layer initialized
[ 0.752654@0] Bluetooth: L2CAP socket layer initialized
[ 0.757855@0] Bluetooth: SCO socket layer initialized
[ 0.763087@0] cfg80211: Calling CRDA to update world regulatory domain
[ 0.770667@0] Switching to clocksource Timer-E
[ 0.782358@0] NET: Registered protocol family 2
[ 0.782859@0] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.788571@0] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.795144@0] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.801577@0] TCP: reno registered
[ 0.804923@0] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.810978@0] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.817702@0] NET: Registered protocol family 1
[ 0.822157@0] Unpacking initramfs...
[ 0.934270@0] Freeing initrd memory: 2060K (c4e08000 - c500b000)
[ 0.935541@0] audit: initializing netlink socket (disabled)
[ 0.940213@0] type=2000 audit(0.850:1): initialized
[ 0.945656@0] bounce pool size: 64 pages
[ 0.953977@0] VFS: Disk quotas dquot_6.5.2
[ 0.954245@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.960975@0] fuse init (API version 7.22)
[ 0.964229@0] msgmni has been set to 1204
[ 0.967752@0] SELinux: Registering netfilter hooks
[ 0.969303@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.975280@0] io scheduler noop registered
[ 0.979328@0] io scheduler deadline registered
[ 0.983878@0] io scheduler cfq registered (default)
[ 1.042076@0] [drm] Initialized drm 1.1.0 20060810
[ 1.042273@0] gpu cooling register okay with err=0
[ 1.048618@0] Mali: Mali device driver loaded
[ 1.050541@0] UMP: UMP device driver 0000 loaded
[ 1.058325@0] loop: module loaded
[ 1.058955@0] tun: Universal TUN/TAP device driver, 1.6
[ 1.063410@0] tun: (C) 1999-2004 Max Krasnyansky
[ 1.069904@0] PPP generic driver version 2.4.2
[ 1.074323@0] PPP BSD Compression module registered
[ 1.078992@0] PPP Deflate Compression module registered
[ 1.084211@0] PPP MPPE Compression module registered
[ 1.089118@0] NET: Registered protocol family 24
[ 1.093958@0] usbcore: registered new interface driver cdc_acm
[ 1.094123@1] 00ffffffffffff000469f523010101013213010380331d782e3585a656489a24
[ 1.094153@1] 125054bfef00d1c0b300a9409500714fa18081400101023a801871382d40582c
[ 1.094183@1] 4500fd1e1100001e000000ff0039434c4d495a3031383135360a000000fd0037
[ 1.094213@1] 4b1e5513000a202020202020000000fc0041535553204d533233380a202001b6
[ 1.094214@1]
[ 1.094244@1] 020325f152900505030227060f0e1f141e1d131211160123097f078301000065
[ 1.094274@1] 030c005000023a801871382d40582c4500fd1e1100001e011d8018711c162058
[ 1.094304@1] 2c2500fd1e1100009e011d007251d01e206e285500fd1e1100001e023a80d072
[ 1.094335@1] 382d40102c4580fd1e1100001e8c0ad08a20e02d10103e9600fd1e3100001806
[ 1.094336@1]
[ 1.094368@1] 00ffffffffffff000469f523010101013213010380331d782e35c5a656489a24
[ 1.094398@1] 12505cbfef00d1c0b300a9409500714f818081400101023a801871382d40582c
[ 1.094428@1] 4500fd1e1100001e000000ff003943cc4d495a3031383135360a000000fd0037
[ 1.094458@1] 4b1e5513000a202020202020000000fc0041535553204d533233380a202001b6
[ 1.094459@1]
[ 1.094489@1] 020325f152900504030207060f0e1f141e1d131211160123097f078301000065
[ 1.094519@1] 030c001000023a801871382d40582c4500fd1e1104001e011d8018711c162058
[ 1.094549@1] 2c2500fd1e1100009e011d007251d01e206e285500fd1e1100001e0a3a80d072
[ 1.094580@1] 382d40102c4580fd1e1100001e8c0ad08a20e02d10103e9e00fd1e1100001806
[ 1.094581@1]
[ 1.094620@1] hdmitx: edid: find IEEEOUT
[ 1.225001@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.233170@0] usbcore: registered new interface driver usb-storage
[ 1.239369@0] usbcore: registered new interface driver usbserial
[ 1.245295@0] usbcore: registered new interface driver usbserial_generic
[ 1.258088@0] ERROR::usb_gadget_probe_driver:1372: usb_gadget_register_driver ENODEV
[ 1.258088@0]
[ 1.267719@0] mousedev: PS/2 mouse device common for all mice
[ 1.273379@0] i2c /dev entries driver
[ 1.276852@0] IR NEC protocol handler initialized
[ 1.281434@0] IR RC5(x) protocol handler initialized
[ 1.286380@0] IR RC6 protocol handler initialized
[ 1.291039@0] IR JVC protocol handler initialized
[ 1.295732@0] IR Sony protocol handler initialized
[ 1.300477@0] IR RC5 (streamzap) protocol handler initialized
[ 1.306203@0] IR SANYO protocol handler initialized
[ 1.311041@0] IR MCE Keyboard/mouse protocol handler initialized
[ 1.317292@0] device-mapper: uevent: version 1.0.3
[ 1.322063@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 1.330506@0] Bluetooth: HCI UART driver ver 2.2
[ 1.334959@0] Bluetooth: HCI H4 protocol initialized
[ 1.340395@0] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.346354@0] usbcore: registered new interface driver usbhid
[ 1.351737@0] usbhid: USB HID core driver
[ 1.356200@0] zram: Created 1 device(s) ...
[ 1.360097@0] efuse===========================================
[ 1.365870@0] efuse: device efuse created
[ 1.369705@0] efuse--------------------------------------------
[ 1.375567@0] vout_init_module
[ 1.378617@0] start init vout module
[ 1.382334@0] create vout attribute ok
[ 1.386366@0] ge2d_init
[ 1.388716@0] ge2d_dev major:245
[ 1.392173@0] ge2d start monitor
[ 1.395397@0] osd_init
[ 1.395408@1] ge2d workqueue monitor start
[ 1.401832@0] osd_probe, vinfo:c0695f70
[ 1.405925@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K
[ 1.413744@0] osd_probe, mydef_var:c0996b38, vinfo:c0695f70
[ 1.419299@0] init fbdev bpp is :32
[ 1.422826@0] ---------------clear framebuffer0 memory
[ 1.474224@0] Console: switching to colour frame buffer device 240x67
[ 1.502377@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0600000, size=1024K
[ 1.510338@0] osd_probe, mydef_var:c0996b38, vinfo:c0695f70
[ 1.515880@0] don't find to display_size_default from mesonfb-dts
[ 1.521922@0] init fbdev bpp is :24
[ 1.528564@0] osd probe ok
[ 1.562466@0] amlvideo-000: V4L2 device registered as video10
[ 1.562814@0] ionvideo-000: V4L2 device registered as video13
[ 1.568313@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
[ 1.576701@0] DI: di_init
[ 1.576792@0] aml_wdt_driver_init,301
[ 1.580330@0] ** disable watchdog
[ 1.584016@0] set uart_ao pinmux use pinctrl subsystem
[ 1.588722@0] P_AO_RTI_PIN_MUX_REG:1801
[ 1.592551@0] start uart_ao_ttyS0:(irq = 122)
[ 1.596890@0] register uart_ao ok
[ 1.600395@0] start uart_a_ttyS1:(irq = 58)
[ 1.604330@0] register uart_a ok
[ 1.607759@0] set uart_b pinmux use pinctrl subsystem
[ 1.612541@0] P_AO_RTI_PIN_MUX_REG:1801
[ 1.616380@0] start uart_b_ttyS2:(irq = 107)
[ 1.620587@0] register uart_b ok
[ 1.624041@0] start uart_d_ttyS4:(irq = 126)
[ 1.628033@0] register uart_d ok
[ 1.631311@0] dwc_otg: version 3.10a 12-MAY-2014
[ 1.635910@0] dwc_otg lm-root: dwc_otg_driver_probe(ef339000)
[ 1.635920@0] dwc_otg_driver_probe NOT match
[ 1.640091@0] dwc_otg lm1: dwc_otg_driver_probe(ef339200)
[ 1.680096@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
[ 1.683070@0] USB (1) use clock source: XTAL input
[ 1.688887@0] dwc_otg lm1: base=0xfe080000
[ 1.688897@0] dwc_otg lm1: dwc_otg_device=0xeea38940
[ 1.709006@0] Core Release: 3.10a
[ 1.709043@0] Setting default values for core params
[ 1.711630@0] curmode: 1, host_only: 1
[ 1.715391@0] dwc_otg lm1: DMA config: BURST_DEFAULT
[ 1.735559@0] Using Buffer DMA mode
[ 1.735587@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 1.737917@0] Working on port type = HOST
[ 1.742132@0] dwc_otg lm1: DWC OTG Controller
[ 1.746279@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
[ 1.752922@0] dwc_otg lm1: irq 63, io mem 0x00000000
[ 1.757852@0] -------hcd->flags.d32 = 0
[ 1.761660@0] Init: Port Power? op_state=1
[ 1.765729@0] Init1: Power Port (0)
[ 1.769787@0] hub 1-0:1.0: USB hub found
[ 1.773086@0] hub 1-0:1.0: 1 port detected
[ 1.777403@0] dwc_otg lm0: dwc_otg_driver_probe(ef339400)
[ 1.777441@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
[ 1.785748@0] USB (0) use clock source: XTAL input
[ 1.791478@0] dwc_otg lm0: base=0xfe040000
[ 1.791488@0] dwc_otg lm0: dwc_otg_device=0xeea5b300
[ 1.811596@0] Core Release: 3.10a
[ 1.811624@0] Setting default values for core params
[ 1.814242@0] curmode: 1, host_only: 0
[ 1.857916@0] dwc_otg lm0: DMA config: BURST_DEFAULT
[ 1.878092@0] Using Buffer DMA mode
[ 1.878120@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 1.880458@0] Working on port type = OTG
[ 1.884363@0] Current port type: SLAVE
[ 1.888294@0] dwc_otg lm0: DWC OTG Controller
[ 1.892429@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
[ 1.899119@0] dwc_otg lm0: irq 62, io mem 0x00000000
[ 1.904486@0] hub 2-0:1.0: USB hub found
[ 1.907910@0] hub 2-0:1.0: 1 port detected
[ 1.912160@0] Dedicated Tx FIFOs mode
[ 1.915988@0] using timer detect id change, eea54c00
[ 1.920674@0] ethernet_driver probe!
[ 1.924131@0] ethernetinit(dbg[c099b6c8]=1)
[ 1.928271@0] ethernet base addr is fe0c0000
[ 1.932531@0] write mac add to:eea7b548: 00 1e 06 34 9a d5 |.\x1e.4..|
[ 1.942952@0] libphy: AMLMAC MII Bus: probed
[ 1.942988@0] eth0: PHY ID 001cc916 at 0 IRQ -1 (0:00) active
[ 1.948710@0] eth0: PHY ID 001cc916 at 1 IRQ -1 (0:01) active
[ 1.954565@0] amvideocap_init_module
[ 1.958073@0] Amlogic A/V streaming port init
[ 1.963814@0] init vdec memsource 161480704->228589567
[ 1.967474@0] [tsync_pcr_init]init success.
[ 1.971670@0] regist mpeg12 codec profile
[ 1.975710@1] Indeed it is in host mode hprt0 = 00021501
[ 1.975713@0] regist mpeg4 codec profile
[ 1.975720@0] amvdec_vc1 module init
[ 1.975763@0] regist vc1 codec profile
[ 1.975765@0] amvdec_h264 module init
[ 1.975841@0] regist h264 codec profile
[ 1.975843@0] amvdec_h265 module init
[ 1.975883@0] regist hevc codec profile
[ 1.975924@0] regist mjpeg codec profile
[ 1.975926@0] amvdec_real module init
[ 1.975966@0] regist real codec profile
[ 1.975968@0] amvdec_avs module init
[ 1.976132@0] regist avc codec profile
[ 1.976135@0] jpegenc module init
[ 1.976318@0] alloc_keep_buffer keep_y_addr ee600000
[ 1.976387@0] alloc_keep_buffer keep_u_addr eec00000
[ 1.976413@0] alloc_keep_buffer keep_v_addr eeb80000
[ 1.976433@0] yaddr=ee600000,u_addr=eec00000,v_addr=eeb80000
[ 2.049488@0] create_ge2d_work_queue video task ok
[ 2.054428@0] SARADC Driver init.
[ 2.057550@0] __saradc_probe__
[ 2.203930@0] saradc calibration: ref_val = 507
[ 2.203961@0] saradc calibration: ref_nominal = 512
[ 2.207673@0] saradc calibration: coef = 4096
[ 2.212261@0] ir irblaster probe
[ 2.215436@0] Remote Driver
[ 2.218042@0] Remote platform_data g_remote_base=fe600580
[ 2.223371@0] set drvdata completed
[ 2.226931@0] device_create_file completed
[ 2.231639@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
[ 2.233832@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.245150@1] Indeed it is in host mode hprt0 = 00001101
[ 2.250300@0] input_register_device completed
[ 2.254759@0] [0x0] = 0x1dd0190
[ 2.257808@0] [0x4] = 0xf800ca
[ 2.260838@0] [0x8] = 0x82006e
[ 2.263925@0] [0xc] = 0x3c0030
[ 2.266899@0] [0x10] = 0x30fa0013
[ 2.270190@0] [0x18] = 0x6f19000
[ 2.273393@0] [0x1c] = 0x9f40
[ 2.276356@0] [0x20] = 0x0
[ 2.279049@0] [0x24] = 0x0
[ 2.281706@0] [0x28] = 0x0
[ 2.284409@0] set_remote_mode[65]
[ 2.287704@0] remote config major:241
[ 2.291554@0] physical address:0x2ec66000
[ 2.295490@0] ==touch_ts_init==
[ 2.298599@0] ==ft5x0x_ts_init==
[ 2.301735@0] ==goodix_ts_init==
[ 2.304996@0] i2c-core: driver [gslx680_compatible] using legacy suspend method
[ 2.312227@0] i2c-core: driver [gslx680_compatible] using legacy resume method
[ 2.319423@0] !!!ntp_ts: ret = 0.
[ 2.322749@0] VTL ct36x TouchScreen driver, .
[ 2.329252@2] i2c-core: driver [ct36x] using legacy suspend method
[ 2.335326@2] i2c-core: driver [ct36x] using legacy resume method
[ 2.341365@2] VTL ct36x TouchScreen driver End.
[ 2.345880@2] ==gsl_ts_init==
[ 2.348841@2] ret=0
[ 2.351044@2] i2c-core: driver [mir3da] using legacy suspend method
[ 2.357141@2] i2c-core: driver [mir3da] using legacy resume method
[ 2.363301@2] i2c-core: driver [lis3dh_acc] using legacy suspend method
[ 2.369866@2] i2c-core: driver [lis3dh_acc] using legacy resume method
[ 2.376411@2] i2c-core: driver [bma222] using legacy suspend method
[ 2.382581@2] i2c-core: driver [bma222] using legacy resume method
[ 2.388804@2] i2c-core: driver [dmard06] using legacy suspend method
[ 2.395072@2] i2c-core: driver [dmard06] using legacy resume method
[ 2.401313@2] lsm303d driver: init
[ 2.404726@2] i2c-core: driver [dmard10] using legacy suspend method
[ 2.410982@2] i2c-core: driver [dmard10] using legacy resume method
[ 2.417258@2] stk8313_init
[ 2.419924@2] ======stk831x init ok======
[ 2.423898@2] stk831x_init
[ 2.426596@2] mxc622x accelerometer driver: init
[ 2.431181@2] i2c-core: driver [mxc622x] using legacy suspend method
[ 2.437492@2] i2c-core: driver [mxc622x] using legacy resume method
[ 2.443713@2] mxc6255xc accelerometer driver: init
[ 2.445924@0] hub 1-1:1.0: USB hub found
[ 2.446251@0] hub 1-1:1.0: 4 ports detected
[ 2.456571@2] i2c-core: driver [mxc6255xc] using legacy suspend method
[ 2.463021@2] i2c-core: driver [mxc6255xc] using legacy resume method
[ 2.469533@2] cm3217 v.1.0.0.1
[ 2.472496@2] i2c-core: driver [elan_epl6814] using legacy suspend method
[ 2.479230@2] i2c-core: driver [elan_epl6814] using legacy resume method
[ 2.485923@2] i2c-core: driver [LTR501] using legacy suspend method
[ 2.492115@2] i2c-core: driver [LTR501] using legacy resume method
[ 2.498398@2] mmc driver version: 1.07, 2014-06-30: eMMC add hw reset function
[ 2.506427@2] host->base fe108e00
[ 2.508815@2] pdata->caps 80000546
[ 2.512122@2] pdata->caps2 20
[ 2.515086@2] get property: port, value:0x00000005
[ 2.521556@2] get property: ocr_avail, value:0x00200000
[ 2.528066@2] get property: f_min, value:0x000493e0
[ 2.534558@2] get property: f_max, value:0x08f0d180
[ 2.541039@2] get property: max_req_size, value:0x00020000
[ 2.547549@2] get property: pinname, str:emmc
[ 2.553335@2] get property: card_type, value:0x00000001
[ 2.559845@2] get property: gpio_dat3, str:BOOT_3
[ 2.565817@2] [is_emmc_exist] host->storage_flag=0, POR_BOOT_VALUE=1
[ 2.623839@0] emmc: mmc_rescan_try_freq: trying to init card at 400000 Hz
[ 2.624984@0] aml_emmc_hw_reset 1367
[ 2.683812@2] [aml_sdhc_probe] aml_sdhc_probe() success!
[ 2.684521@2] host->base fe108c20
[ 2.686803@2] pdata->caps 7
[ 2.689547@2] pdata->caps2 0
[ 2.692406@2] get property: port, value:0x00000001
[ 2.698920@2] get property: ocr_avail, value:0x00200000
[ 2.705406@2] get property: f_min, value:0x000493e0
[ 2.711888@2] get property: f_max, value:0x02faf080
[ 2.718394@2] get property: f_max_w, value:0x02faf080
[ 2.724182@0] usb 1-1.1: new full-speed USB device number 3 using dwc_otg
[ 2.731642@2] get property: max_req_size, value:0x00020000
[ 2.738135@2] get property: irq_in, value:0x00000003
[ 2.744630@2] get property: irq_out, value:0x00000005
[ 2.751118@2] get property: gpio_cd, str:CARD_6
[ 2.757102@2] get property: pinname, str:sd
[ 2.762716@2] get property: card_type, value:0x00000005
[ 2.769223@2] get property: gpio_dat3, str:CARD_4
[ 2.773294@1] emmc: BKOPS_EN bit is not set
[ 2.773296@1] ###check hw reset function is already enabled here
[ 2.785330@2] get property: gpio_volsw, str:GPIOAO_3
[ 2.791489@2] aml_sd_voltage_switch[1297] : Switched to voltage -> 3.30 V
[ 2.796675@1] [aml_sd_voltage_switch]\x1b[0;40;32m switch to 1.8V for a non-uhs device.
[ 2.796675@1] \x1b[0m
[ 2.796684@1] [aml_sdhc_print_err]\x1b[0;40;32m emmc: rsp CRC error, port=5, Cmd13 Arg 00010000, xfer_step=3, status=3, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, iSTA=0x4, STAT=0xf0003e
[ 2.796684@1] \x1b[0mPinmux: REG2=0x00000000, REG3=0x00000000, REG4=0x70000300, REG5=0x00000000, REG6=0x00003f4f, REG8=0x00000000
[ 2.796697@1] ***********SDHC_REGS***********
[ 2.796699@1] SDHC_ARGU: 0x00000e00
[ 2.796701@1] SDHC_SEND: 0x0000004d
[ 2.796703@1] SDHC_CTRL: 0xe7ffe002
[ 2.796705@1] SDHC_STAT: 0x00f0003e
[ 2.796707@1] SDHC_CLKC: 0x0002f84c
[ 2.796709@1] SDHC_ADDR: 0x3ec80000
[ 2.796711@1] SDHC_PDMA: 0x2c43bcf0
[ 2.796713@1] SDHC_MISC: 0xe0000150
[ 2.796715@1] SDHC_DATA: 0x00000000
[ 2.796716@1] SDHC_ICTL: 0x00003067
[ 2.796718@1] SDHC_ISTA: 0x00000004
[ 2.796720@1] SDHC_SRST: 0x00000000
[ 2.796722@1] SDHC_ESTA: 0x00000000
[ 2.796724@1] SDHC_ENHC: 0x00fe0cff
[ 2.796725@1] SDHC_CLK2: 0x00001425
[ 2.801427@1] emmc: new HS200 MMC card at address 0001, clock 141666666, 8-bit-bus-width
[ 2.801814@1] mmcblk0: emmc:0001 SDW16G 14.6 GiB
[ 2.801997@1] mmcblk0boot0: emmc:0001 SDW16G partition 1 4.00 MiB
[ 2.802177@1] mmcblk0boot1: emmc:0001 SDW16G partition 2 4.00 MiB
[ 2.803022@1] mmcblk0: p1 p2
[ 2.804941@1] mmcblk0boot1: unknown partition table
[ 2.806006@1] mmcblk0boot0: unknown partition table
[ 2.930530@0] input: zhihaihe elec c0 zhihaihe keyboard as /devices/lm1/usb1/1-1/1-1.1/1-1.1:1.0/input/input1
[ 2.940059@0] hid-generic 0003:FFFF:104E.0001: input: USB HID v1.11 Keyboard [zhihaihe elec c0 zhihaihe keyboard] on usb-lm1-1.1/input0
[ 2.955864@0] input: zhihaihe elec c0 zhihaihe keyboard as /devices/lm1/usb1/1-1/1-1.1/1-1.1:1.1/input/input2
[ 2.962236@0] hid-generic 0003:FFFF:104E.0002: input: USB HID v1.11 Keyboard [zhihaihe elec c0 zhihaihe keyboard] on usb-lm1-1.1/input1
[ 2.973872@2] reg:2620,clearmask=80008,setmask=10001
[ 2.973877@2] reg:2621,clearmask=ff000000,set pin=49
[ 2.973881@2] reg:2623,clearmask=7000,setmask=7
[ 2.973885@2] reg:2620,clearmask=200020,setmask=1
[ 2.973888@2] reg:2622,clearmask=ff00,set pin=49
[ 2.973892@2] reg:2623,clearmask=700000,setmask=7
[ 3.022865@2] aml_sd_voltage_switch[1297] : Switched to voltage -> 3.30 V
[ 3.023873@1] aml_sd_voltage_switch[1297] : Switched to voltage -> 3.30 V
[ 3.063811@1] [aml_sdio_probe] aml_sdio_probe() success!
[ 3.063937@1] [dsp]DSP start addr 0xc5e00000
[ 3.067754@1] [dsp]register dsp to char divece(257)
[ 3.073280@1] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
[ 3.079013@1] amlogic rfkill init
[ 3.082257@1] aml_hw_crypto initialization.
[ 3.087069@1] enter rt5616_modinit
[ 3.089566@1] dummy_codec_platform_probe
[ 3.093744@1] enter aml_i2s_dai_probe
[ 3.093754@1] i2s get no clk src setting in dts, use the default mpll 0
[ 3.100111@1] enter aml_pcm_dai_probe
[ 3.100166@1] [aml-spdif-dai]enter aml_dai_spdif_init
[ 3.105118@1] [aml-spdif-dai]aml_spdif_probe
[ 3.109482@1] test codec dummy_codec
[ 3.112927@1] using external codec, index = 1
[ 3.117274@1] using external dummy codec
[ 3.121256@1] enter spdif_dit_probe
[ 3.124718@1] aml_spdif_unmute
[ 3.127940@1] codec_name = dummy_codec.0
[ 3.132028@1] enter aml_set_bias_level level: 1
[ 3.132065@1] enter aml_set_bias_level level: 1
[ 3.132086@1] enter aml_set_bias_level level: 1
[ 3.132093@1] enter aml_set_bias_level level: 2
[ 3.132171@1] enter aml_asoc_init
[ 3.132200@1] spk_event delay_time = 130
[ 3.136635@1] aml-i2s 0:playback preallocate_dma_buffer: area=f0542000, addr=3ed00000, size=524288
[ 3.144923@1] aml-i2s 1:capture preallocate_dma_buffer: area=f05c4000, addr=3ec40000, size=65536
[ 3.153300@1] aml_snd_m8 aml_m8_sound_card.4: dummy_codec aml-i2s-dai.0 mapping ok
[ 3.161404@1] enter aml_set_bias_level level: 1
[ 3.161413@1] enter aml_set_bias_level level: 2
[ 3.162570@1] aml-i2s 0:playback preallocate_dma_buffer: area=f0701000, addr=3ee00000, size=524288
[ 3.170572@1] aml-i2s 1:capture preallocate_dma_buffer: area=f0783000, addr=3ec60000, size=65536
[ 3.178949@1] aml_snd_m8 aml_m8_sound_card.4: dit-hifi aml-spdif-dai.0 mapping ok
[ 3.186897@1] enter aml_set_bias_level level: 1
[ 3.186905@1] enter aml_set_bias_level level: 2
[ 3.187047@1] enter aml_set_bias_level level: 1
[ 3.187055@1] enter aml_set_bias_level level: 2
[ 3.187968@1] enter aml_set_bias_level level: 1
[ 3.187978@1] enter aml_set_bias_level level: 2
[ 3.188108@1] -----ext_codec=1---
[ 3.190076@1] aml_snd_m8: faild to get mute_gpio!
[ 3.194773@1] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
[ 3.200877@1] GACT probability NOT on
[ 3.204387@1] Mirror/redirect action on
[ 3.208175@1] u32 classifier
[ 3.211029@1] Actions configured
[ 3.214597@1] Netfilter messages via NETLINK v0.30.
[ 3.219481@1] nf_conntrack version 0.5.0 (13573 buckets, 54292 max)
[ 3.226234@1] ctnetlink v0.93: registering with nfnetlink.
[ 3.231189@1] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.238238@1] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.244426@1] xt_time: kernel timezone is -0000
[ 3.248949@1] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.254343@1] arp_tables: (C) 2002 David S. Miller
[ 3.258963@1] TCP: cubic registered
[ 3.262812@1] NET: Registered protocol family 10
[ 3.267723@1] mip6: Mobile IPv6
[ 3.270109@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.275869@1] sit: IPv6 over IPv4 tunneling driver
[ 3.281292@1] NET: Registered protocol family 17
[ 3.285028@1] NET: Registered protocol family 15
[ 3.289636@1] Bridge firewalling registered
[ 3.293895@1] Bluetooth: RFCOMM TTY layer initialized
[ 3.298771@1] Bluetooth: RFCOMM socket layer initialized
[ 3.304047@1] Bluetooth: RFCOMM ver 1.11
[ 3.307924@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.313378@1] Bluetooth: BNEP filters: protocol multicast
[ 3.318770@1] Bluetooth: BNEP socket layer initialized
[ 3.323868@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.329924@1] Bluetooth: HIDP socket layer initialized
[ 3.335060@1] NET: Registered protocol family 35
[ 3.340067@1] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 3.347442@1] Registering SWP/SWPB emulation handler
[ 3.352344@1] enter meson_pm_init
[ 3.355770@1] enter meson_pm_probe!
[ 3.359101@1] meson_pm_probe done !
[ 3.363027@1] registered taskstats version 1
[ 3.366896@1] regulator-dummy: disabling
[ 3.370953@1] Mali DRM initialize, driver name: mali_drm, version 2.1
[ 3.377400@1] [drm] Initialized mali_drm 2.1.1 20140306 on minor 0
[ 3.383272@1] Mali DRM initialize, driver name: mali_drm, version 2.1
[ 3.389907@1] [drm] Initialized mali_drm 2.1.1 20140306 on minor 1
[ 3.396023@1] aml_rtc rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
[ 3.403191@1] ### dt-test ### No testcase data in device tree; not running tests
[ 3.410647@1] meson_cpufreq: no voltage_control prop
[ 3.415483@1] voltage_control = 0
[ 3.419202@1] GTP driver installing...
[ 3.424020@1] buf[0]=cf,buf[1]=b2,err=4
[ 3.427588@1] adc=406,TS_C=15,flag=1
[ 3.431137@1] efuse_flag=a
[ 3.433841@1] amlogic_thermal_probe, this chip is trimmed, use thermal
[ 3.440319@1] amlogic-thermal aml_thermal: amlogic thermal probe start
[ 3.446824@1] #thermal-cells=7
[ 3.449841@1] pdata->temp_trip_count=4
[ 3.453567@1] temperature=70 on trip point=0
[ 3.457816@1] fixing high_freq=1488001 to 1488000 at trip point 0,level=0
[ 3.464569@1] fixing low_freq=1488001 to 1488000 at trip point 0,level=0
[ 3.471229@1] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
[ 3.477645@1] cpu[0] core num==3
[ 3.480839@1] gpu[0] core num==2
[ 3.484052@1] temperature=80 on trip point=1
[ 3.488285@1] fixing high_freq=1200001 to 1200000 at trip point 1,level=3
[ 3.495048@1] fixing low_freq=1200001 to 1200000 at trip point 1,level=3
[ 3.501708@1] gpu[1].gpu_high_freq=435,tmp_level[1].gpu_high_freq=435
[ 3.508123@1] cpu[1] core num==2
[ 3.511318@1] gpu[1] core num==2
[ 3.514531@1] temperature=90 on trip point=2
[ 3.518764@1] fixing high_freq=800001 to 696000 at trip point 2,level=8
[ 3.525360@1] fixing low_freq=800001 to 696000 at trip point 2,level=8
[ 3.531840@1] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
[ 3.538258@1] cpu[2] core num==1
[ 3.541450@1] gpu[2] core num==1
[ 3.544664@1] temperature=110 on trip point=3
[ 3.548983@1] fixing high_freq=-1 to -22 at trip point 3,level=-1
[ 3.555054@1] fixing low_freq=-1 to -22 at trip point 3,level=-1
[ 3.561020@1] gpu[3].gpu_high_freq=-1,tmp_level[3].gpu_high_freq=-1
[ 3.567263@1] cpu[3] core num==-1
[ 3.570544@1] gpu[3] core num==-1
[ 3.573844@1] idle interval=1000
[ 3.577039@1] pdata->name:aml_thermal
[ 3.580936@1] tmp_trip[0].cpu_core_upper=1
[ 3.584771@1] tmp_trip[1].cpu_core_upper=2
[ 3.588822@1] tmp_trip[2].cpu_core_upper=3
[ 3.592892@1] tmp_trip[3].cpu_core_upper=-1
[ 3.597062@1] aml_thermal bind thermal-cpucore-0 okay !
[ 3.602275@1] aml_thermal bind thermal-cpufreq-0 okay !
[ 3.607446@1] pdata->tmp_trip[0].gpu_lower_level=1
[ 3.612193@1] pdata->tmp_trip[0].gpu_upper_level=1
[ 3.616977@1] pdata->tmp_trip[1].gpu_lower_level=2
[ 3.621718@1] pdata->tmp_trip[1].gpu_upper_level=2
[ 3.626501@1] pdata->tmp_trip[2].gpu_lower_level=4
[ 3.631243@1] pdata->tmp_trip[2].gpu_upper_level=4
[ 3.636026@1] pdata->tmp_trip[3].gpu_lower_level=-1
[ 3.640854@1] pdata->tmp_trip[3].gpu_upper_level=-1
[ 3.645723@1] aml_thermal bind thermal-gpufreq-0 okay !
[ 3.651025@1] amlogic: Kernel Thermal management registered
[ 3.656454@1] amlogic-thermal aml_thermal: amlogic thermal probe done
[ 3.663136@1] input: cec_input as /devices/virtual/input/input3
[ 3.668929@1] ALSA device list:
[ 3.671853@1] #0: AML-M8AUDIO
[ 3.675346@1] config uart_ao_ttyS0:: Character length 8bits/char
[ 3.693815@1] Changing uart_ao_ttyS0: baud from 0 to 115200
[ 3.714017@1] Freeing unused kernel memory: 224K (c090e000 - c0946000)
[ 3.763966@3] systemd-udevd[114]: starting version 204
[ 3.938133@0] tvmode set to 720p
[ 3.938133@0]
[ 3.938175@0] don't set the same mode as current.
[ 3.978944@0] tvmode set to 720p
[ 3.978944@0]
[ 3.978998@0] don't set the same mode as current.
[ 4.057149@2] force enable DISCARD here for ext4 fs
[ 4.057982@2] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 4.063915@2] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 4.392411@0] EXT4-fs (mmcblk0p2): orphan cleanup on readonly fs
[ 4.392813@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 16444
[ 4.393053@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 1968
[ 4.393216@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 3365
[ 4.393297@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 3130
[ 4.393371@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 3383
[ 4.393441@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 17524
[ 4.393584@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 16455
[ 4.393667@0] EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 17508
[ 4.393736@0] EXT4-fs (mmcblk0p2): 8 orphan inodes deleted
[ 4.398350@0] EXT4-fs (mmcblk0p2): recovery complete
[ 4.428654@0] checked enable EXT4 DISCARD here
[ 4.428687@0] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.704637@2] config uart_ao_ttyS0:: Character length 8bits/char
[ 4.757147@2] init: plymouth-upstart-bridge main process (167) terminated with status 1
[ 4.759974@2] init: plymouth-upstart-bridge main process ended, respawning
[ 4.770643@3] config uart_ao_ttyS0:: Character length 8bits/char
[ 4.795382@3] init: plymouth-upstart-bridge main process (176) terminated with status 1
[ 4.799089@3] init: plymouth-upstart-bridge main process ended, respawning
[ 4.814449@0] config uart_ao_ttyS0:: Character length 8bits/char
[ 4.836129@1] init: plymouth-upstart-bridge main process (179) terminated with status 1
[ 4.838543@1] init: plymouth-upstart-bridge main process ended, respawning
[ 4.856369@0] config uart_ao_ttyS0:: Character length 8bits/char
[ 5.295008@3] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 5.892155@2] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 5.906591@2] systemd-udevd[328]: starting version 204
[ 6.284171@2] systemd-udevd[343]: renamed network interface eth0 to eth1
[ 6.460938@1] aml_audio_i2s_mute_flag: flag=0
[ 6.460979@1] aml_audio_set_spdif_mute: flag=0
[ 6.460987@1] aml_spdif_unmute
[ 7.248540@2] ionvideo open
[ 7.248703@2] ionvideo_stop_generating!!!!
[ 7.248725@2] ionvideo release
[ 10.167419@3] aml_audio_i2s_mute_flag: flag=0
[ 10.167473@3] aml_audio_set_spdif_mute: flag=0
[ 10.167487@3] aml_spdif_unmute
[ 10.642549@0] netdev_open
[ 10.642568@0] Ethernet reset
[ 10.642578@0] NET MDA descpter start addr=ee564000
[ 10.643601@0] phy_interface = 0
[ 10.643616@0] aml_phy_init: trying to attach to 0:01
[ 7.247986@0] amlvideo openamlvideo close
[ 10.675026@0] --1--write mac add to:eea7b548: 00 1e 06 34 9a d5 |.\x1e.4..|
[ 10.675069@0] --2--write mac add to:eea7b548: 00 1e 06 34 9a d5 |.\x1e.4..|
[ 10.675086@0] write mac add to:eea7b548: 00 1e 06 34 9a d5 |.\x1e.4..|
[ 10.675105@0] Current DMA mode=0, set mode=621c100
[ 10.675153@0] eth1: opened (irq 40).
[ 10.675171@0] ether leave promiscuous mode
[ 10.675177@0] ether leave all muticast mode
[ 10.675308@0] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 11.133576@0] init: plymouth-upstart-bridge main process ended, respawning
[ 11.477779@1] create_disp_get_ump_secure_id******0
[ 11.478522@1] create_disp_get_ump_secure_id******1
[ 11.965301@1] init: plymouth-stop pre-start process (936) terminated with status 1
[ 14.673996@0] libphy: 0:01 - Link is Up - 1000/Full
[ 14.674039@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.976603@0] ----aml_hw_iec958_init,runtime->rate=44100--
[ 15.976624@0] [aml-spdif-dai]enterd aml_hw_iec958_init,set_clock:-1,sample_rate=5
[ 15.976630@0] audio_set_958_clk, freq=5,
[ 15.976639@0] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 15.976646@0] iec958 mode PCM16
[ 15.976655@0] IEC958 16bit
[ 16.004047@0] enter aml_set_bias_level level: 1
[ 16.004061@0] enter aml_set_bias_level level: 2
[ 16.004187@0] ----aml_hw_iec958_init,runtime->rate=44100--
[ 16.004207@0] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 16.004216@0] iec958 mode PCM16
[ 16.004225@0] IEC958 16bit
[ 16.043878@0] enter aml_set_bias_level level: 1
[ 16.043895@0] enter aml_set_bias_level level: 2
[ 16.173607@1] [aml-spdif-dai]aiu 958 playback enable
[ 16.180716@0] spdifin_fifo1_set_buf
[ 16.180739@0] spdifin_reg_set: clk_rate=159375000
[ 16.181208@0] enter aml_set_bias_level level: 1
[ 16.181222@0] enter aml_set_bias_level level: 2
[ 16.181342@0] spdifin_fifo1_set_buf
[ 16.181357@0] spdifin_reg_set: clk_rate=159375000
[ 16.181509@0] enter aml_set_bias_level level: 1
[ 16.181518@0] enter aml_set_bias_level level: 2
[ 16.256343@2] [aml-spdif-dai]spdif in capture enable
[ 17.283739@2] alsa capture long time no data, quit xrun!
[ 18.303722@2] alsa capture long time no data, quit xrun!
[ 19.323699@2] alsa capture long time no data, quit xrun!
[ 20.343666@2] alsa capture long time no data, quit xrun!
[ 21.368186@2] [aml-spdif-dai]spdif in capture disable
[ 21.368330@0] enter aml_set_bias_level level: 1
[ 21.368340@0] enter aml_set_bias_level level: 2
[ 21.368685@3] [aml-spdif-dai]aiu 958 playback disable
[ 21.389031@1] spdifin_fifo1_set_buf
[ 21.389053@1] spdifin_reg_set: clk_rate=159375000
[ 21.389190@1] enter aml_set_bias_level level: 1
[ 21.389199@1] enter aml_set_bias_level level: 2
[ 21.389276@1] spdifin_fifo1_set_buf
[ 21.389288@1] spdifin_reg_set: clk_rate=159375000
[ 21.389369@0] enter aml_set_bias_level level: 1
[ 21.389378@0] enter aml_set_bias_level level: 2
[ 21.411193@0] enter aml_set_bias_level level: 1
[ 21.411206@0] enter aml_set_bias_level level: 2
[ 21.421549@1] spdifin_fifo1_set_buf
[ 21.421569@1] spdifin_reg_set: clk_rate=159375000
[ 21.421678@0] enter aml_set_bias_level level: 1
[ 21.421686@0] enter aml_set_bias_level level: 2
[ 21.421751@1] spdifin_fifo1_set_buf
[ 21.421762@1] spdifin_reg_set: clk_rate=159375000
[ 21.421831@0] enter aml_set_bias_level level: 1
[ 21.421838@0] enter aml_set_bias_level level: 2
[ 21.423875@0] enter aml_set_bias_level level: 1
[ 21.423887@0] enter aml_set_bias_level level: 2
[ 21.424803@1] spdifin_fifo1_set_buf
[ 21.424822@1] spdifin_reg_set: clk_rate=159375000
[ 21.424894@0] enter aml_set_bias_level level: 1
[ 21.424910@0] enter aml_set_bias_level level: 2
[ 21.424970@1] spdifin_fifo1_set_buf
[ 21.424980@1] spdifin_reg_set: clk_rate=159375000
[ 21.425034@0] enter aml_set_bias_level level: 1
[ 21.425042@0] enter aml_set_bias_level level: 2
[ 21.425178@0] enter aml_set_bias_level level: 1
[ 21.425186@0] enter aml_set_bias_level level: 2
[ 21.426280@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 21.426290@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 21.426298@1] iec958 mode PCM16
[ 21.426306@1] IEC958 16bit
[ 21.437838@0] enter aml_set_bias_level level: 1
[ 21.437849@0] enter aml_set_bias_level level: 2
[ 21.437939@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 21.437947@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 21.437954@1] iec958 mode PCM16
[ 21.437962@1] IEC958 16bit
[ 21.449483@0] enter aml_set_bias_level level: 1
[ 21.449494@0] enter aml_set_bias_level level: 2
[ 21.459500@1] spdifin_fifo1_set_buf
[ 21.459520@1] spdifin_reg_set: clk_rate=159375000
[ 21.459625@0] enter aml_set_bias_level level: 1
[ 21.459634@0] enter aml_set_bias_level level: 2
[ 21.459708@1] spdifin_fifo1_set_buf
[ 21.459719@1] spdifin_reg_set: clk_rate=159375000
[ 21.459793@0] enter aml_set_bias_level level: 1
[ 21.459801@0] enter aml_set_bias_level level: 2
[ 21.459928@0] enter aml_set_bias_level level: 1
[ 21.459936@0] enter aml_set_bias_level level: 2
[ 21.460985@1] spdifin_fifo1_set_buf
[ 21.461001@1] spdifin_reg_set: clk_rate=159375000
[ 21.461088@0] enter aml_set_bias_level level: 1
[ 21.461096@0] enter aml_set_bias_level level: 2
[ 21.461155@1] spdifin_fifo1_set_buf
[ 21.461166@1] spdifin_reg_set: clk_rate=159375000
[ 21.461234@0] enter aml_set_bias_level level: 1
[ 21.461242@0] enter aml_set_bias_level level: 2
[ 21.461367@0] enter aml_set_bias_level level: 1
[ 21.461375@0] enter aml_set_bias_level level: 2
[ 21.462166@1] spdifin_fifo1_set_buf
[ 21.462182@1] spdifin_reg_set: clk_rate=159375000
[ 21.462245@0] enter aml_set_bias_level level: 1
[ 21.462253@0] enter aml_set_bias_level level: 2
[ 21.462319@1] spdifin_fifo1_set_buf
[ 21.462329@1] spdifin_reg_set: clk_rate=159375000
[ 21.462376@0] enter aml_set_bias_level level: 1
[ 21.462383@0] enter aml_set_bias_level level: 2
[ 21.462505@0] enter aml_set_bias_level level: 1
[ 21.462513@0] enter aml_set_bias_level level: 2
[ 21.463821@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 21.463831@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 21.463839@1] iec958 mode PCM16
[ 21.463847@1] IEC958 16bit
[ 21.475504@0] enter aml_set_bias_level level: 1
[ 21.475516@0] enter aml_set_bias_level level: 2
[ 21.475583@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 21.475592@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 21.475599@1] iec958 mode PCM16
[ 21.475606@1] IEC958 16bit
[ 21.487124@0] enter aml_set_bias_level level: 1
[ 21.487135@0] enter aml_set_bias_level level: 2
[ 21.488547@1] spdifin_fifo1_set_buf
[ 21.488568@1] spdifin_reg_set: clk_rate=159375000
[ 21.488661@0] enter aml_set_bias_level level: 1
[ 21.488702@0] enter aml_set_bias_level level: 2
[ 21.488766@1] spdifin_fifo1_set_buf
[ 21.488778@1] spdifin_reg_set: clk_rate=159375000
[ 21.488847@0] enter aml_set_bias_level level: 1
[ 21.488855@0] enter aml_set_bias_level level: 2
[ 21.488975@0] enter aml_set_bias_level level: 1
[ 21.488983@0] enter aml_set_bias_level level: 2
[ 21.490041@1] spdifin_fifo1_set_buf
[ 21.490057@1] spdifin_reg_set: clk_rate=159375000
[ 21.490142@0] enter aml_set_bias_level level: 1
[ 21.490150@0] enter aml_set_bias_level level: 2
[ 21.490200@1] spdifin_fifo1_set_buf
[ 21.490211@1] spdifin_reg_set: clk_rate=159375000
[ 21.490279@0] enter aml_set_bias_level level: 1
[ 21.490293@0] enter aml_set_bias_level level: 2
[ 21.490407@0] enter aml_set_bias_level level: 1
[ 21.490420@0] enter aml_set_bias_level level: 2
[ 21.491208@1] spdifin_fifo1_set_buf
[ 21.491224@1] spdifin_reg_set: clk_rate=159375000
[ 21.491294@0] enter aml_set_bias_level level: 1
[ 21.491302@0] enter aml_set_bias_level level: 2
[ 21.491358@1] spdifin_fifo1_set_buf
[ 21.491368@1] spdifin_reg_set: clk_rate=159375000
[ 21.491425@0] enter aml_set_bias_level level: 1
[ 21.491432@0] enter aml_set_bias_level level: 2
[ 21.491567@0] enter aml_set_bias_level level: 1
[ 21.491574@0] enter aml_set_bias_level level: 2
[ 21.498212@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 21.498225@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 21.498233@1] iec958 mode PCM16
[ 21.498241@1] IEC958 16bit
[ 21.509785@0] enter aml_set_bias_level level: 1
[ 21.509807@0] enter aml_set_bias_level level: 2
[ 21.509885@1] ----aml_hw_iec958_init,runtime->rate=44100--
[ 21.509894@1] ----aml_hw_iec958_init,runtime->rate=44100,sample_rate=5--
[ 21.509901@1] iec958 mode PCM16
[ 21.509908@1] IEC958 16bit
[ 21.521431@0] enter aml_set_bias_level level: 1
[ 21.521443@0] enter aml_set_bias_level level: 2
[ 21.555939@0] [aml-spdif-dai]aiu 958 playback enable
[ 26.574726@0] [aml-spdif-dai]aiu 958 playback disable
[ 31.583567@0] enter aml_set_bias_level level: 1
[ 31.583580@0] enter aml_set_bias_level level: 2
[ 132.842202@3] aml_audio_i2s_mute_flag: flag=0
[ 132.842236@3] aml_audio_set_spdif_mute: flag=0
[ 132.842242@3] aml_spdif_unmute
[ 133.160498@1] init: plymouth-stop pre-start process (1654) terminated with status 1
[ 154.733995@0] usb 1-1.2: new low-speed USB device number 4 using dwc_otg
[ 154.864738@0] input: Logitech USB-PS/2 Optical Mouse as /devices/lm1/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
[ 154.865123@0] hid-generic 0003:046D:C00E.0003: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-lm1-1.2/input0
[ 172.337614@2] ionvideo open
[ 172.337696@2] ionvideo_stop_generating!!!!
[ 172.337720@2] ionvideo release
[ 172.337782@2] amlvideo openamlvideo closeionvideo open
[ 172.338110@2] ionvideo_stop_generating!!!!
[ 172.338136@2] ionvideo release
[ 196.349574@0] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[ 1304.887801@2] The PHY does not support set_wol, was CONFIG_MICREL_PHY enabled?