dmesg - aio
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.2.0-57-generic (buildd@toyol) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #87-Ubuntu SMP Tue Nov 12 21:35:10 UTC 2013 (Ubuntu 3.2.0-57.87-generic 3.2.52)
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfb3f000 (usable)
BIOS-e820: 00000000bfb3f000 - 00000000bfbbf000 (reserved)
BIOS-e820: 00000000bfbbf000 - 00000000bfebf000 (ACPI NVS)
BIOS-e820: 00000000bfebf000 - 00000000bfef6000 (ACPI data)
BIOS-e820: 00000000bfef6000 - 00000000bff00000 (usable)
BIOS-e820: 00000000bff00000 - 00000000e0000000 (reserved)
BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec11000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000011f000000 (usable)
NX (Execute Disable) protection: active
SMBIOS 2.7 present.
DMI: Hewlett-Packard HP Pavilion g4 Notebook PC/3564, BIOS F.24 06/30/2011
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x11f000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-FFFFF write-through
MTRR variable ranges enabled:
0 base 0000000000 mask FF80000000 write-back
1 base 0080000000 mask FFC0000000 write-back
2 base 00BFEBD000 mask FFFFFFF000 uncachable
3 base 00FFE00000 mask FFFFE00000 write-protect
4 disabled
5 disabled
6 disabled
7 disabled
TOM2: 000000011f000000 aka 4592M
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
last_pfn = 0xbff00 max_arch_pfn = 0x400000000
found SMP MP-table at [ffff8800000fe1b0] fe1b0
initial memory mapped : 0 - 20000000
Base memory trampoline at [ffff88000009a000] 9a000 size 20480
Using GB pages for direct mapping
init_memory_mapping: 0000000000000000-00000000bff00000
0000000000 - 0080000000 page 1G
0080000000 - 00bfe00000 page 2M
00bfe00000 - 00bff00000 page 4k
kernel direct mapping tables up to bff00000 @ 1fffd000-20000000
init_memory_mapping: 0000000100000000-000000011f000000
0100000000 - 011f000000 page 2M
kernel direct mapping tables up to 11f000000 @ bfefe000-bff00000
RAMDISK: 364be000 - 37257000
ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM)
ACPI: XSDT 00000000bfef5120 0007C (v01 HPQOEM SLIC-MPC 00000001 01000013)
ACPI: FACP 00000000bfef4000 000F4 (v04 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
ACPI: DSDT 00000000bfee0000 0F574 (v01 HP INSYDE F0000000 ACPI 00040000)
ACPI: FACS 00000000bfc95000 00040
ACPI: HPET 00000000bfef3000 00038 (v01 HP INSYDE 00000001 ACPI 00040000)
ACPI: APIC 00000000bfef2000 00084 (v02 HP INSYDE 00000001 ACPI 00040000)
ACPI: MCFG 00000000bfef1000 0003C (v01 HP INSYDE 00000001 ACPI 00040000)
ACPI: ASF! 00000000bfef0000 000A5 (v32 HP INSYDE 00000001 ACPI 00040000)
ACPI: BOOT 00000000bfedf000 00028 (v01 HP INSYDE 00000001 ACPI 00040000)
ACPI: SLIC 00000000bfede000 00176 (v01 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
ACPI: WDRT 00000000bfedd000 00047 (v01 HP INSYDE 00000001 ACPI 00040000)
ACPI: MSDM 00000000bfedc000 00055 (v03 HP INSYDE 00000001 ACPI 00040000)
ACPI: SSDT 00000000bfedb000 00E28 (v01 HP INSYDE 00000001 AMD 00000001)
ACPI: SSDT 00000000bfed9000 0190A (v02 HP INSYDE 00000001 MSFT 04000000)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-000000011f000000
Initmem setup node 0 0000000000000000-000000011f000000
NODE_DATA [000000011effb000 - 000000011effffff]
[ffffea0000000000-ffffea00047fffff] PMD -> [ffff88011ae00000-ffff88011e5fffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0011f000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x000bfb3f
0: 0x000bfef6 -> 0x000bff00
0: 0x00100000 -> 0x0011f000
On node 0 totalpages: 912088
DMA zone: 64 pages used for memmap
DMA zone: 5 pages reserved
DMA zone: 3914 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 764809 pages, LIFO batch:31
Normal zone: 1984 pages used for memmap
Normal zone: 124992 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10228210 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000bfb3f000 - 00000000bfbbf000
PM: Registered nosave memory: 00000000bfbbf000 - 00000000bfebf000
PM: Registered nosave memory: 00000000bfebf000 - 00000000bfef6000
PM: Registered nosave memory: 00000000bff00000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f8000000
PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fec11000
PM: Registered nosave memory: 00000000fec11000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff88011ec00000 s83136 r8192 d23360 u524288
pcpu-alloc: s83136 r8192 d23360 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Node order, mobility grouping on. Total pages: 893715
Policy zone: Normal
PID hash table entries: 4096 (order: 3, 32768 bytes)
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 3494748k/4702208k available (6586k kernel code, 1053856k absent, 153604k reserved, 6619k data, 924k init)
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
NR_IRQS:16640 nr_irqs:712 16
spurious 8259A interrupt: IRQ7.
vt handoff: transparent VT on vt#7
Console: colour dummy device 80x25
console [tty0] enabled
allocated 29360128 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 1397.572 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 2795.14 BogoMIPS (lpj=5590288)
pid_max: default: 32768 minimum: 301
Security Framework initialized
AppArmor: AppArmor initialized
Yama: becoming mindful.
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
tseg: 00bff00000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
ACPI: Core revision 20110623
ftrace: allocating 26597 entries in 105 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD A6-3400M APU with Radeon(tm) HD Graphics stepping 00
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 9a000
NMI watchdog enabled, takes one hw-pmu counter.
#2
smpboot cpu 2: start_ip = 9a000
NMI watchdog enabled, takes one hw-pmu counter.
#3 Ok.
smpboot cpu 3: start_ip = 9a000
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 4 CPUs
Total of 4 processors activated (11179.77 BogoMIPS).
devtmpfs: initialized
EVM: security.selinux
EVM: security.SMACK64
EVM: security.capability
PM: Registering ACPI NVS region at bfbbf000 (3145728 bytes)
print_constraints: dummy:
RTC time: 15:12:47, date: 12/05/13
NET: Registered protocol family 16
Extended Config Space enabled on 0 nodes
ACPI: bus type pci registered
Trying to unpack rootfs image as initramfs...
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
[Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
Freeing initrd memory: 13924k freed
ACPI: EC: GPE = 0x5, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
HEST: Table not found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff]
pci_root PNP0A08:00: host bridge window [mem 0x000cc000-0x000cffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff]
pci_root PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff]
pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xf7ffffff]
pci_root PNP0A08:00: host bridge window [mem 0xfc000000-0xfed3ffff]
pci_root PNP0A08:00: host bridge window [mem 0xfed45000-0xffffffff]
pci_root PNP0A08:00: ignoring host bridge window [mem 0x000cc000-0x000cffff] (conflicts with Video ROM [mem 0x000c0000-0x000cf1ff])
pci 0000:00:00.0: [1022:1705] type 0 class 0x000600
pci 0000:00:01.0: [1002:9647] type 0 class 0x000300
pci 0000:00:01.0: reg 10: [mem 0xe0000000-0xefffffff pref]
pci 0000:00:01.0: reg 14: [io 0x4000-0x40ff]
pci 0000:00:01.0: reg 18: [mem 0xf0300000-0xf033ffff]
pci 0000:00:01.0: supports D1 D2
pci 0000:00:01.1: [1002:1714] type 0 class 0x000403
pci 0000:00:01.1: reg 10: [mem 0xf0344000-0xf0347fff]
pci 0000:00:01.1: supports D1 D2
pci 0000:00:04.0: [1022:1709] type 1 class 0x000604
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: [1022:170a] type 1 class 0x000604
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: [1022:170b] type 1 class 0x000604
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:11.0: [1022:7804] type 0 class 0x000106
pci 0000:00:11.0: reg 10: [io 0x4118-0x411f]
pci 0000:00:11.0: reg 14: [io 0x4124-0x4127]
pci 0000:00:11.0: reg 18: [io 0x4110-0x4117]
pci 0000:00:11.0: reg 1c: [io 0x4120-0x4123]
pci 0000:00:11.0: reg 20: [io 0x4100-0x410f]
pci 0000:00:11.0: reg 24: [mem 0xf034e000-0xf034e7ff]
pci 0000:00:12.0: [1022:7807] type 0 class 0x000c03
pci 0000:00:12.0: reg 10: [mem 0xf034d000-0xf034dfff]
pci 0000:00:12.2: [1022:7808] type 0 class 0x000c03
pci 0000:00:12.2: reg 10: [mem 0xf034c000-0xf034c0ff]
pci 0000:00:12.2: supports D1 D2
pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:12.2: PME# disabled
pci 0000:00:13.0: [1022:7807] type 0 class 0x000c03
pci 0000:00:13.0: reg 10: [mem 0xf034b000-0xf034bfff]
pci 0000:00:13.2: [1022:7808] type 0 class 0x000c03
pci 0000:00:13.2: reg 10: [mem 0xf034a000-0xf034a0ff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
pci 0000:00:14.0: [1022:780b] type 0 class 0x000c05
pci 0000:00:14.2: [1022:780d] type 0 class 0x000403
pci 0000:00:14.2: reg 10: [mem 0xf0340000-0xf0343fff 64bit]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
pci 0000:00:14.3: [1022:780e] type 0 class 0x000601
pci 0000:00:14.4: [1022:780f] type 1 class 0x000604
pci 0000:00:16.0: [1022:7807] type 0 class 0x000c03
pci 0000:00:16.0: reg 10: [mem 0xf0349000-0xf0349fff]
pci 0000:00:16.2: [1022:7808] type 0 class 0x000c03
pci 0000:00:16.2: reg 10: [mem 0xf0348000-0xf03480ff]
pci 0000:00:16.2: supports D1 D2
pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:16.2: PME# disabled
pci 0000:00:18.0: [1022:1700] type 0 class 0x000600
pci 0000:00:18.1: [1022:1701] type 0 class 0x000600
pci 0000:00:18.2: [1022:1702] type 0 class 0x000600
pci 0000:00:18.3: [1022:1703] type 0 class 0x000600
pci 0000:00:18.4: [1022:1704] type 0 class 0x000600
pci 0000:00:18.5: [1022:1718] type 0 class 0x000600
pci 0000:00:18.6: [1022:1716] type 0 class 0x000600
pci 0000:00:18.7: [1022:1719] type 0 class 0x000600
pci 0000:01:00.0: [10ec:8176] type 0 class 0x000280
pci 0000:01:00.0: reg 10: [io 0x3000-0x30ff]
pci 0000:01:00.0: reg 18: [mem 0xf0200000-0xf0203fff 64bit]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:04.0: PCI bridge to [bus 01-01]
pci 0000:00:04.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:04.0: bridge window [mem 0xf0200000-0xf02fffff]
pci 0000:02:00.0: [10ec:8136] type 0 class 0x000200
pci 0000:02:00.0: reg 10: [io 0x2000-0x20ff]
pci 0000:02:00.0: reg 18: [mem 0xf0004000-0xf0004fff 64bit pref]
pci 0000:02:00.0: reg 20: [mem 0xf0000000-0xf0003fff 64bit pref]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:05.0: PCI bridge to [bus 02-02]
pci 0000:00:05.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:05.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
pci 0000:03:00.0: [10ec:5209] type 0 class 0x00ff00
pci 0000:03:00.0: reg 10: [mem 0xf0100000-0xf0100fff]
pci 0000:03:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: PME# supported from D1 D2 D3hot
pci 0000:03:00.0: PME# disabled
pci 0000:00:06.0: PCI bridge to [bus 03-03]
pci 0000:00:06.0: bridge window [mem 0xf0100000-0xf01fffff]
pci 0000:00:14.4: PCI bridge to [bus 04-04] (subtractive decode)
pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0xe0000000-0xf7ffffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfed3ffff] (subtractive decode)
pci 0000:00:14.4: bridge window [mem 0xfed45000-0xffffffff] (subtractive decode)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.VGA_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AZAL._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
pci0000:00: Requesting ACPI _OSC control (0x1d)
pci0000:00: ACPI _OSC control (0x19) granted
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:00:01.0
i2c-core: driver [aat2870] using legacy suspend method
i2c-core: driver [aat2870] using legacy resume method
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff
reserve RAM buffer: 00000000bfb3f000 - 00000000bfffffff
reserve RAM buffer: 00000000bff00000 - 00000000bfffffff
reserve RAM buffer: 000000011f000000 - 000000011fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 32-bit 14.318180 MHz counter
Switching to clocksource hpet
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-ff]
pnp 00:00: [io 0x0000-0x0cf7 window]
pnp 00:00: [io 0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000c0000-0x000c3fff window]
pnp 00:00: [mem 0x000c4000-0x000c7fff window]
pnp 00:00: [mem 0x000c8000-0x000cbfff window]
pnp 00:00: [mem 0x000cc000-0x000cffff window]
pnp 00:00: [mem 0x000d0000-0x000d3fff window]
pnp 00:00: [mem 0x000d4000-0x000d7fff window]
pnp 00:00: [mem 0x000d8000-0x000dbfff window]
pnp 00:00: [mem 0x000dc000-0x000dffff window]
pnp 00:00: [mem 0x000e0000-0x000e3fff window]
pnp 00:00: [mem 0x000e4000-0x000e7fff window]
pnp 00:00: [mem 0x000e8000-0x000ebfff window]
pnp 00:00: [mem 0x000ec000-0x000effff window]
pnp 00:00: [mem 0xe0000000-0xf7ffffff window]
pnp 00:00: [mem 0xfc000000-0xfed3ffff window]
pnp 00:00: [mem 0xfed45000-0xffffffff window]
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [mem 0xfec00000-0xfec00fff]
pnp 00:01: [mem 0xfee00000-0xfee00fff]
pnp 00:01: [mem 0xf8000000-0xfbffffff]
pnp 00:01: [mem 0xfed80000-0xfed80fff]
pnp 00:01: [mem 0xfed40000-0xfed44fff]
system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
system 00:01: [mem 0xfed80000-0xfed80fff] has been reserved
system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:02: [irq 0 disabled]
pnp 00:02: [irq 8]
pnp 00:02: [mem 0xfed00000-0xfed003ff]
pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:03: [io 0x0000-0x000f]
pnp 00:03: [io 0x0081-0x008f]
pnp 00:03: [io 0x00c0-0x00df]
pnp 00:03: [dma 4]
pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:04: [io 0x00f0-0x00fe]
pnp 00:04: [irq 13]
pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:05: [io 0x0070-0x0071]
pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:06: [io 0x0061]
pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:07: [io 0x0060]
pnp 00:07: [io 0x0064]
pnp 00:07: [irq 1]
pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:08: [irq 12]
pnp 00:08: Plug and Play ACPI device, IDs SYN1e41 SYN1e00 SYN0002 PNP0f13 (active)
pnp 00:09: [io 0x0010-0x001f]
pnp 00:09: [io 0x002e-0x002f]
pnp 00:09: [io 0x0072-0x0073]
pnp 00:09: [io 0x0080]
pnp 00:09: [io 0x00b0-0x00b1]
pnp 00:09: [io 0x0092]
pnp 00:09: [io 0x0400-0x04cf]
pnp 00:09: [io 0x04d0-0x04d1]
pnp 00:09: [io 0x04d6]
pnp 00:09: [io 0x0680-0x06ff]
pnp 00:09: [io 0x077a]
pnp 00:09: [io 0x0c00-0x0c01]
pnp 00:09: [io 0x0c14]
pnp 00:09: [io 0x0c50-0x0c52]
pnp 00:09: [io 0x0c6c]
pnp 00:09: [io 0x0c6f]
pnp 00:09: [io 0x0cd0-0x0cdb]
pnp 00:09: [io 0x0840-0x0847]
pnp 00:09: [io 0x0380-0x0387]
system 00:09: [io 0x0400-0x04cf] has been reserved
system 00:09: [io 0x04d0-0x04d1] has been reserved
system 00:09: [io 0x04d6] has been reserved
system 00:09: [io 0x0680-0x06ff] has been reserved
system 00:09: [io 0x077a] has been reserved
system 00:09: [io 0x0c00-0x0c01] has been reserved
system 00:09: [io 0x0c14] has been reserved
system 00:09: [io 0x0c50-0x0c52] has been reserved
system 00:09: [io 0x0c6c] has been reserved
system 00:09: [io 0x0c6f] has been reserved
system 00:09: [io 0x0cd0-0x0cdb] has been reserved
system 00:09: [io 0x0840-0x0847] has been reserved
system 00:09: [io 0x0380-0x0387] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0a: [mem 0x000e0000-0x000fffff]
pnp 00:0a: [mem 0xffe00000-0xffffffff]
system 00:0a: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0a: [mem 0xffe00000-0xffffffff] has been reserved
system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
pci 0000:03:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:06.0: BAR 15: assigned [mem 0xf0400000-0xf04fffff pref]
pci 0000:00:04.0: PCI bridge to [bus 01-01]
pci 0000:00:04.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:04.0: bridge window [mem 0xf0200000-0xf02fffff]
pci 0000:00:05.0: PCI bridge to [bus 02-02]
pci 0000:00:05.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:05.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0xf0400000-0xf040ffff pref]
pci 0000:00:06.0: PCI bridge to [bus 03-03]
pci 0000:00:06.0: bridge window [mem 0xf0100000-0xf01fffff]
pci 0000:00:06.0: bridge window [mem 0xf0400000-0xf04fffff pref]
pci 0000:00:14.4: PCI bridge to [bus 04-04]
pci 0000:00:04.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:06.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
pci_bus 0000:00: resource 10 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:00: resource 11 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:00: resource 12 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:00: resource 13 [mem 0x000dc000-0x000dffff]
pci_bus 0000:00: resource 14 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:00: resource 15 [mem 0x000e4000-0x000e7fff]
pci_bus 0000:00: resource 16 [mem 0x000e8000-0x000ebfff]
pci_bus 0000:00: resource 17 [mem 0x000ec000-0x000effff]
pci_bus 0000:00: resource 18 [mem 0xe0000000-0xf7ffffff]
pci_bus 0000:00: resource 19 [mem 0xfc000000-0xfed3ffff]
pci_bus 0000:00: resource 20 [mem 0xfed45000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:01: resource 1 [mem 0xf0200000-0xf02fffff]
pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
pci_bus 0000:03: resource 1 [mem 0xf0100000-0xf01fffff]
pci_bus 0000:03: resource 2 [mem 0xf0400000-0xf04fffff pref]
pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000c3fff]
pci_bus 0000:04: resource 8 [mem 0x000c4000-0x000c7fff]
pci_bus 0000:04: resource 9 [mem 0x000c8000-0x000cbfff]
pci_bus 0000:04: resource 10 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:04: resource 11 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:04: resource 12 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:04: resource 13 [mem 0x000dc000-0x000dffff]
pci_bus 0000:04: resource 14 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:04: resource 15 [mem 0x000e4000-0x000e7fff]
pci_bus 0000:04: resource 16 [mem 0x000e8000-0x000ebfff]
pci_bus 0000:04: resource 17 [mem 0x000ec000-0x000effff]
pci_bus 0000:04: resource 18 [mem 0xe0000000-0xf7ffffff]
pci_bus 0000:04: resource 19 [mem 0xfc000000-0xfed3ffff]
pci_bus 0000:04: resource 20 [mem 0xfed45000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
pci 0000:00:01.0: Boot video device
pci 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:12.0: PCI INT A disabled
pci 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:12.2: PCI INT B disabled
pci 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:13.0: PCI INT A disabled
pci 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:13.2: PCI INT B disabled
pci 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:16.0: PCI INT A disabled
pci 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:16.2: PCI INT B disabled
PCI: CLS 64 bytes, default 64
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff8800bbb3f000 - ffff8800bfb3f000
software IO TLB at phys 0xbbb3f000 - 0xbfb3f000
Simple Boot Flag at 0x44 set to 0x1
perf: AMD IBS detected (0x000000ff)
audit: initializing netlink socket (disabled)
type=2000 audit(1386256367.812:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
fuse init (API version 7.17)
msgmni has been set to 6852
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
ACPI: AC Adapter [ACAD] (on-line)
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
ACPI: acpi_idle registered with cpuidle
[Firmware Bug]: Invalid critical threshold (0)
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (28 C)
ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
ACPI: Battery Slot [BAT0] (battery present)
ERST: Table is not found!
GHES: HEST is not enabled!
Linux agpgart interface v0.103
brd: module loaded
loop: module loaded
ahci 0000:00:11.0: version 3.0
ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:11.0: irq 40 for MSI/MSI-X
ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part sxs
scsi0 : ahci
scsi1 : ahci
ata1: SATA max UDMA/133 abar m2048@0xf034e000 port 0xf034e100 irq 40
ata2: SATA max UDMA/133 abar m2048@0xf034e000 port 0xf034e180 irq 40
Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
QUIRK: Enable AMD PLL fix
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0xf034c000
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:13.2: debug port 1
ehci_hcd 0000:00:13.2: irq 17, io mem 0xf034a000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 5 ports detected
ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:16.2: EHCI Host Controller
ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
ehci_hcd 0000:00:16.2: debug port 1
ehci_hcd 0000:00:16.2: irq 17, io mem 0xf0348000
ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:12.0: irq 18, io mem 0xf034d000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.0: irq 18, io mem 0xf034b000
ACPI: Battery Slot [BAT0] (battery present)
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 5 ports detected
ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:16.0: OHCI Host Controller
ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:16.0: irq 18, io mem 0xf0349000
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver libusual
i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Registering the dns_resolver key type
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
Magic number: 9:171:234
rtc_cmos 00:05: setting system clock to 2013-12-05 15:12:49 UTC (1386256369)
powernow-k8: Found 1 AMD A6-3400M APU with Radeon(tm) HD Graphics (4 cpu cores) (version 2.20.00)
powernow-k8: Core Performance Boosting: on.
powernow-k8: 0 : pstate 0 (1400 MHz)
powernow-k8: 1 : pstate 1 (1300 MHz)
powernow-k8: 2 : pstate 2 (1200 MHz)
powernow-k8: 3 : pstate 3 (1100 MHz)
powernow-k8: 4 : pstate 4 (1000 MHz)
powernow-k8: 5 : pstate 5 (900 MHz)
powernow-k8: 6 : pstate 6 (800 MHz)
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
usb 1-1: new high-speed USB device number 2 using ehci_hcd
Initializing USB Mass Storage driver...
scsi2 : usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: Hitachi HTS547564A9E384, JEDOA50A, max UDMA/100
ata1.00: 1250263728 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
ata2.00: ATAPI: hp DVDRAM GT31L, MR52, max UDMA/100
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54756 JEDO PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2.00: configured for UDMA/100
scsi 1:0:0:0: CD-ROM hp DVDRAM GT31L MR52 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
usb 1-3: new high-speed USB device number 3 using ehci_hcd
Refined TSC clocksource calibration: 1397.458 MHz.
Switching to clocksource tsc
sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 > sda4
sd 0:0:0:0: [sda] Attached SCSI disk
Freeing unused kernel memory: 924k freed
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 1588k freed
Freeing unused kernel memory: 1188k freed
udevd[103]: starting version 175
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 41 for MSI/MSI-X
r8169 0000:02:00.0: eth0: RTL8105e at 0xffffc90000670000, 2c:27:d7:ec:e0:af, XID 00a00000 IRQ 41
usb 5-2: new low-speed USB device number 2 using ohci_hcd
input: USB Optical Mouse as /devices/pci0000:00/0000:00:13.0/usb5/5-2/5-2:1.0/input/input4
generic-usb 0003:192F:0416.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:13.0-2/input0
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
scsi 2:0:0:0: Direct-Access WD My Passport 0748 1015 PQ: 0 ANSI: 6
scsi 2:0:0:1: Enclosure WD SES Device 1015 PQ: 0 ANSI: 6
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 2:0:0:1: Attached scsi generic sg3 type 13
sd 2:0:0:0: [sdb] 976707584 512-byte logical blocks: (500 GB/465 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 47 00 10 08
sd 2:0:0:0: [sdb] No Caching mode page found
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] No Caching mode page found
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] No Caching mode page found
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI disk
ses 2:0:0:1: Attached Enclosure device
EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
ADDRCONF(NETDEV_UP): eth0: link is not ready
udevd[335]: starting version 175
lp: driver loaded but no devices found
cfg80211: Calling CRDA to update world regulatory domain
wmi: Mapper loaded
acpi device:00: registered as cooling_device4
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
rts_pstor: module is from the staging directory, the quality is unknown, you have been warned.
Initializing Realtek PCIE storage driver...
rts_pstor 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Resource length: 0x1000
Original address: 0xf0100000, remapped address: 0xffffc90000638000
pci->irq = 18
rtsx_acquire_irq: chip->msi_en = 0, pci->irq = 18
rts_pstor 0000:03:00.0: setting latency timer to 64
ACPI: resource piix4_smbus [io 0x0b00-0x0b07] conflicts with ACPI region SMB0 [io 0xb00-0xb0f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
scsi3 : SCSI emulation for PCI-Express Mass Storage devices
rts_pstor: waiting for device to settle before scanning
input: HP WMI hotkeys as /devices/virtual/input/input6
rtl8192ce 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
rtl8192ce 0000:01:00.0: setting latency timer to 64
psmouse serio1: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xd00073/0x240000/0xa0400
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
rts_pstor: device scan complete
scsi 3:0:0:0: Direct-Access Generic- xD/SD/M.S. 1.00 PQ: 0 ANSI: 0 CCS
Bad LUN (0:1)
Bad target number (1:0)
Bad target number (2:0)
Bad target number (3:0)
Bad target number (4:0)
Bad target number (5:0)
Bad target number (6:0)
Bad target number (7:0)
sd 3:0:0:0: Attached scsi generic sg4 type 0
sd 3:0:0:0: [sdc] Attached SCSI removable disk
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
cfg80211: Pending regulatory request, waiting for it to be processed...
cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: Calling CRDA for country: EC
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2484 MHz
cfg80211: Regulatory domain changed to country: EC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 20000 KHz), (300 mBi, 1700 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 20000 KHz), (300 mBi, 2300 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 20000 KHz), (300 mBi, 3000 mBm)
ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
rtlwifi: wireless switch is on
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
Disabling lock debugging due to kernel taint
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device HP Webcam-101 (05c8:021e)
input: HP Webcam-101 as /devices/pci0000:00/0000:00:12.2/usb1/1-3/1-3:1.0/input/input8
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
[fglrx] Maximum main memory to use for locked dma buffers: 3277 MBytes.
[fglrx] vendor: 1002 device: 9647 count: 1
[fglrx] ioport: bar 1, base 0x4000, size: 0x100
pci 0000:00:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:01.0: setting latency timer to 64
[fglrx] Kernel PAT support is enabled
[fglrx] module loaded - fglrx 13.10.10 [May 23 2013] with 1 minors
type=1400 audit(1386227579.037:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=948 comm="apparmor_parser"
type=1400 audit(1386227579.037:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=888 comm="apparmor_parser"
type=1400 audit(1386227579.037:4): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=887 comm="apparmor_parser"
type=1400 audit(1386227579.037:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=948 comm="apparmor_parser"
type=1400 audit(1386227579.037:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=888 comm="apparmor_parser"
type=1400 audit(1386227579.037:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=887 comm="apparmor_parser"
type=1400 audit(1386227579.037:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=948 comm="apparmor_parser"
type=1400 audit(1386227579.037:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=888 comm="apparmor_parser"
type=1400 audit(1386227579.037:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=887 comm="apparmor_parser"
snd_hda_intel 0000:00:01.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
snd_hda_intel 0000:00:01.1: irq 42 for MSI/MSI-X
snd_hda_intel 0000:00:01.1: setting latency timer to 64
HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0
input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
vesafb: mode is 1366x768x32, linelength=5504, pages=0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90005100000, using 4160k, total 4160k
Console: switching to colour frame buffer device 170x48
fb0: VESA VGA frame buffer device
EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
init: failsafe main process (1192) killed by TERM signal
type=1400 audit(1386227586.113:11): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1265 comm="apparmor_parser"
type=1400 audit(1386227586.117:12): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1265 comm="apparmor_parser"
type=1400 audit(1386227586.117:13): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1265 comm="apparmor_parser"
type=1400 audit(1386227586.197:14): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1268 comm="apparmor_parser"
type=1400 audit(1386227586.197:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1268 comm="apparmor_parser"
type=1400 audit(1386227586.253:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1269 comm="apparmor_parser"
type=1400 audit(1386227586.253:17): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1269 comm="apparmor_parser"
type=1400 audit(1386227586.253:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1264 comm="apparmor_parser"
type=1400 audit(1386227586.257:19): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=1264 comm="apparmor_parser"
type=1400 audit(1386227586.325:20): apparmor="STATUS" operation="profile_load" name="/usr/sbin/mysqld" pid=1272 comm="apparmor_parser"
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
r8169 0000:02:00.0: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth0: link is not ready
kvm: Nested Virtualization enabled
kvm: Nested Paging enabled
rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin
rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin
wlan0: Trigger new scan to find an IBSS to join
vboxdrv: Found 4 processor cores.
vboxdrv: fAsync=0 offMin=0x220 offMax=0x4a1f
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 4.1.12_Ubuntu (interface 0x00190000).
vboxpci: IOMMU not found (not registered)
fglrx_pci 0000:00:01.0: irq 43 for MSI/MSI-X
[fglrx] Firegl kernel thread PID: 1565
[fglrx] Firegl kernel thread PID: 1566
[fglrx] Firegl kernel thread PID: 1567
[fglrx] IRQ 43 Enabled
[fglrx] Reserved FB block: Shared offset:0, size:1000000
[fglrx] Reserved FB block: Unshared offset:fc36000, size:3ca000
[fglrx] Reserved FB block: Unshared offset:1fff4000, size:c000
wlan0: Trigger new scan to find an IBSS to join
[fglrx] ATIF platform detected with notification ID: 0x81
wlan0: Creating new IBSS network, BSSID 92:99:65:60:f8:21
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
wlan0: no IPv6 routers present
wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_UP): eth0: link is not ready
r8169 0000:02:00.0: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin
ADDRCONF(NETDEV_UP): wlan0: link is not ready
device eth0 entered promiscuous mode
r8169 0000:02:00.0: eth0: link up
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
show_signal_msg: 36 callbacks suppressed
chromium-browse[4032]: segfault at 44 ip 00007f767995851f sp 00007fff236013d0 error 4 in fglrx_dri.so[7f7678c1d000+1d9a000]
chromium-browse[4045]: segfault at 44 ip 00007fccf2c0a51f sp 00007fff2c44ca90 error 4 in fglrx_dri.so[7fccf1ecf000+1d9a000]
chromium-browse[4065]: segfault at 44 ip 00007f04acf2f51f sp 00007fffa99a7e80 error 4 in fglrx_dri.so[7f04ac1f4000+1d9a000]
usb 2-1: new high-speed USB device number 3 using ehci_hcd
scsi4 : usb-storage 2-1:1.0
scsi 4:0:0:0: Direct-Access Kingston DT 101 G2 1.00 PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: Attached scsi generic sg5 type 0
sd 4:0:0:0: [sdd] 15638480 512-byte logical blocks: (8.00 GB/7.45 GiB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sdd] No Caching mode page found
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sd 4:0:0:0: [sdd] No Caching mode page found
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sdd: sdd1
sd 4:0:0:0: [sdd] No Caching mode page found
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sd 4:0:0:0: [sdd] Attached SCSI removable disk
usb 2-1: USB disconnect, device number 3
snow[25858]: segfault at 0 ip 00007fd2f2e1e800 sp 00007fff296d6d58 error 4 in fglrx_dri.so[7fd2f1c50000+1d9a000]
usb 2-1: new high-speed USB device number 4 using ehci_hcd
scsi5 : usb-storage 2-1:1.0
scsi 5:0:0:0: Direct-Access kingston DT 101 G2 8.07 PQ: 0 ANSI: 4
sd 5:0:0:0: Attached scsi generic sg5 type 0
sd 5:0:0:0: [sdd] 15360000 512-byte logical blocks: (7.86 GB/7.32 GiB)
sd 5:0:0:0: [sdd] Write Protect is off
sd 5:0:0:0: [sdd] Mode Sense: 23 00 00 00
sd 5:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd4
sd 5:0:0:0: [sdd] Attached SCSI removable disk
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): Filesystem has been set read-only
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
sdd: detected capacity change from 7864320000 to 0
usb 2-1: USB disconnect, device number 4
usb 2-1: new high-speed USB device number 5 using ehci_hcd
scsi6 : usb-storage 2-1:1.0
scsi 6:0:0:0: Direct-Access kingston DT 101 G2 8.07 PQ: 0 ANSI: 4
sd 6:0:0:0: Attached scsi generic sg5 type 0
sd 6:0:0:0: [sdd] 15360000 512-byte logical blocks: (7.86 GB/7.32 GiB)
sd 6:0:0:0: [sdd] Write Protect is off
sd 6:0:0:0: [sdd] Mode Sense: 23 00 00 00
sd 6:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd4
sd 6:0:0:0: [sdd] Attached SCSI removable disk
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): Filesystem has been set read-only
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
usb 2-1: USB disconnect, device number 5
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): FAT read failed (blocknr 8643)
FAT-fs (sdd1): Directory bread(block 30649) failed
FAT-fs (sdd1): Directory bread(block 30650) failed
FAT-fs (sdd1): Directory bread(block 30651) failed
FAT-fs (sdd1): Directory bread(block 30652) failed
FAT-fs (sdd1): Directory bread(block 30653) failed
FAT-fs (sdd1): Directory bread(block 30654) failed
FAT-fs (sdd1): Directory bread(block 30655) failed
FAT-fs (sdd1): Directory bread(block 30656) failed
FAT-fs (sdd1): Directory bread(block 30649) failed
FAT-fs (sdd1): Directory bread(block 30650) failed
FAT-fs (sdd1): Directory bread(block 30651) failed
FAT-fs (sdd1): Directory bread(block 30652) failed
FAT-fs (sdd1): Directory bread(block 30653) failed
FAT-fs (sdd1): Directory bread(block 30654) failed
FAT-fs (sdd1): Directory bread(block 30655) failed
FAT-fs (sdd1): Directory bread(block 30656) failed
FAT-fs (sdd1): Directory bread(block 30649) failed
FAT-fs (sdd1): Directory bread(block 30650) failed
FAT-fs (sdd1): Directory bread(block 30651) failed
FAT-fs (sdd1): Directory bread(block 30652) failed
FAT-fs (sdd1): Directory bread(block 30653) failed
FAT-fs (sdd1): Directory bread(block 30654) failed
FAT-fs (sdd1): Directory bread(block 30655) failed
FAT-fs (sdd1): Directory bread(block 30656) failed
usb 2-1: new high-speed USB device number 6 using ehci_hcd
scsi7 : usb-storage 2-1:1.0
scsi 7:0:0:0: Direct-Access kingston DT 101 G2 8.07 PQ: 0 ANSI: 4
sd 7:0:0:0: Attached scsi generic sg5 type 0
sd 7:0:0:0: [sdd] 15360000 512-byte logical blocks: (7.86 GB/7.32 GiB)
sd 7:0:0:0: [sdd] Write Protect is off
sd 7:0:0:0: [sdd] Mode Sense: 23 00 00 00
sd 7:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd4
sd 7:0:0:0: [sdd] Attached SCSI removable disk
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): Filesystem has been set read-only
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
FAT-fs (sdd1): error, fat_get_cluster: invalid cluster chain (i_pos 0)
sdd: detected capacity change from 7864320000 to 0
usb 2-1: USB disconnect, device number 6
r8169 0000:02:00.0: eth0: link down
r8169 0000:02:00.0: eth0: link up