dmesg - CacheBench
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
print_constraints: dummy:
NET: Registered protocol family 16
print_constraints: vddpu: 725 1300 mV at 700 mV fast normal
print_constraints: vddcore: 725 1300 mV at 1100 mV fast normal
print_constraints: vddsoc: 725 1300 mV at 1200 mV fast normal
print_constraints: vdd2p5: 2000 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 1400 mV at 1100 mV fast normal
print_constraints: vdd3p0: 2625 3400 mV at 3000 mV fast normal
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
bio: create slab at 0
mxs-dma mxs-dma-apbh: initialized
print_constraints: SPKVDD: 4200 mV
print_constraints: vmmc: 3300 mV
SCSI subsystem initialized
libata version 3.00 loaded.
spi_imx imx6q-ecspi.0: probed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Freescale USB OTG Driver loaded, $Revision: 1.55 $
mc_pfuze 1-0008: ID: 0,Full lay: 1 ,Metal lay: 1
mc_pfuze 1-0008: FAB: 0 ,FIN: 0
print_constraints: PFUZE100_SW1A: 300 1875 mV at 1300 mV
print_constraints: PFUZE100_SW1B: 300 1875 mV at 300 mV
print_constraints: PFUZE100_SW1C: 300 1875 mV at 1300 mV
print_constraints: PFUZE100_SW2: 800 3950 mV at 3300 mV
print_constraints: PFUZE100_SW3A: 400 1975 mV at 1500 mV
print_constraints: PFUZE100_SW3B: 400 1975 mV at 1500 mV
print_constraints: PFUZE100_SW4: 800 3950 mV at 3150 mV
print_constraints: PFUZE100_SWBST: 5000 5150 mV at 5000 mV
print_constraints: PFUZE100_VSNVS: 1200 3000 mV at 1800 mV
print_constraints: PFUZE100_VREFDDR: at 750 mV
print_constraints: PFUZE100_VGEN1: 800 1550 mV at 1500 mV
print_constraints: PFUZE100_VGEN2: 800 1550 mV at 1500 mV
print_constraints: PFUZE100_VGEN3: 1800 3300 mV at 2800 mV
print_constraints: PFUZE100_VGEN4: 1800 3300 mV at 1800 mV
print_constraints: PFUZE100_VGEN5: 1800 3300 mV at 3000 mV
print_constraints: PFUZE100_VGEN6: 1800 3300 mV at 3300 mV
imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
max17135_regulator_init abort: EPDC not enabled
max17135 2-0048: PMIC MAX17135 for eInk display
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PMU: registered new PMU device of type 0
Static Power Management for Freescale i.MX6
wait mode is enabled for i.MX6
cpaddr = c0880000 suspend_iram_base=c091c000
PM driver module loaded
IMX usb wakeup probe
the wakeup pdata is 0xbfeae3c0
add wake up source irq 75
IMX usb wakeup probe
the wakeup pdata is 0xbfeae8c0
cpu regulator init ldo=1
_regulator_get: get() with no identifier
mx6_cpu_regulator_init: failed to get pu regulator
i.MXC CPU frequency driver
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1751
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
mxc_mipi_dsi mxc_mipi_dsi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 240x67
mxc_sdc_fb mxc_sdc_fb.1: Can't get fb option for mxcfb1!
mxc_sdc_fb mxc_sdc_fb.2: Can't get fb option for mxcfb2!
mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb
_regulator_get: get() with no identifier
imx-sdma imx-sdma: loaded firmware 1.1
imx-sdma imx-sdma: initialized
fbcvt: 1920x1080@60: CVT Name - 2.073M9
imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled, bootconsole disabled
loop: module loaded
Can't recover from RESET HBA!
No sata disk.
m25p80 spi0.0: unrecognized JEDEC id ffffff
GPMI NAND driver registered. (IMX)
vcan: Virtual CAN interface driver
CAN device driver interface
flexcan netdevice driver
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
add wake up source irq 72
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
input: max11801_ts as /devices/platform/imx-i2c.1/i2c-1/1-0048/input/input1
egalax_ts 1-0004: egalax_ts: failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
egalax_ts 2-0004: egalax_ts: failed to read firmware version
egalax_ts: probe of 2-0004 failed with error -5
usb 1-1: new high speed USB device number 2 using fsl-ehci
elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
hub 1-1:1.0: USB hub found
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
hub 1-1:1.0: 4 ports detected
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input2
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
input: mma845x as /devices/virtual/input/input3
imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCIATH3K protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA
mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
mmc2: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
usb 1-1.1: new high speed USB device number 3 using fsl-ehci
VPU initialized
mxc_asrc registered
Thermal calibration data is 0x5704b77d
Anatop Thermal registered as thermal_zone0
anatop_thermal_probe: default cooling device is cpufreq!
Registered led device: chg_now_led
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
Cirrus Logic CS42888 ALSA SoC Codec Driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
usb 1-1.1: config 1 interface 1 altsetting 0 bulk endpoint 0x5 has invalid maxpacket 16
usb 1-1.1: config 1 interface 1 altsetting 0 bulk endpoint 0x86 has invalid maxpacket 16
mmc0: new high speed DDR MMC card at address 0001
mmcblk0: mmc0:0001 SEM08G 7.39 GiB
wm8962 0-001a: customer id 0 revision D
mmcblk0boot0: mmc0:0001 SEM08G partition 1 2.00 MiB
mmcblk0boot1: mmc0:0001 SEM08G partition 2 2.00 MiB
mmcblk0: unknown partition table
mmcblk0boot1: unknown partition table
mmcblk0boot0: unknown partition table
input: WM8962 Beep Generator as /devices/platform/imx-i2c.0/i2c-0/0-001a/input/input4
asoc: wm8962 imx-ssi.1 mapping ok
imx_3stack asoc driver
asoc: mxc-hdmi-soc imx-hdmi-soc-dai.0 mapping ok
ALSA device list:
#0: wm8962-audio
#1: imx-hdmi-soc
NET: Registered protocol family 26
usb 1-1.1: device v1307 p0368 is not supported
scsi0 : usb-storage 1-1.1:1.0
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
Bus freq driver module loaded
Bus freq driver Enabled
mxc_dvfs_core_probe
DVFS driver module loaded
regulator_init_complete: PFUZE100_VGEN6: incomplete constraints, leaving on
regulator_init_complete: PFUZE100_VGEN3: incomplete constraints, leaving on
regulator_init_complete: PFUZE100_VGEN2: incomplete constraints, leaving on
regulator_init_complete: PFUZE100_VGEN1: incomplete constraints, leaving on
snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
Waiting for root device /dev/mmcblk1p1...
mmc2: new high speed SDHC card at address b368
mmcblk1: mmc2:b368 00000 7.51 GiB
mmcblk1: p1
EXT4-fs (mmcblk1p1): recovery complete
EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:25.
Freeing init memory: 204K
scsi 0:0:0:0: Direct-Access Generic Storage Device 0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] Attached SCSI removable disk
ehci_fsl_bus_suspend begins, Host 1
ehci_fsl_bus_suspend ends, Host 1
ehci_fsl_bus_resume begins, Host 1
ov5642_read_reg:write reg error:reg=300a
ehci_fsl_bus_resume ends, Host 1
ov5642_probe:cannot find camera
ov5640_read_reg:write reg error:reg=300a
ov5640_probe:cannot find camera
init: plymouth main process (1437) killed by SEGV signal
init: plymouth-splash main process (5099) terminated with status 2
ehci_fsl_bus_suspend begins, Host 1
ehci_fsl_bus_suspend ends, Host 1
init: failsafe main process (5217) killed by TERM signal
eth6: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
init: apport pre-start process (5378) terminated with status 1
init: apport post-stop process (5401) terminated with status 1
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
init: tty1 main process (5587) killed by TERM signal
PHY: 1:01 - Link is Up - 100/Full
usb 1-1.1: USB disconnect, device number 3
usb 1-1.1: new high speed USB device number 4 using fsl-ehci
usb 1-1.1: config 1 interface 1 altsetting 0 bulk endpoint 0x5 has invalid maxpacket 16
usb 1-1.1: config 1 interface 1 altsetting 0 bulk endpoint 0x86 has invalid maxpacket 16
usb 1-1.1: device v1307 p0368 is not supported
scsi1 : usb-storage 1-1.1:1.0
ehci_fsl_bus_resume begins, Host 1
ehci_fsl_bus_resume ends, Host 1
scsi 1:0:0:0: Direct-Access Generic Storage Device 0.00 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] Attached SCSI removable disk
ehci_fsl_bus_suspend begins, Host 1
ehci_fsl_bus_suspend ends, Host 1
usb 1-1.1: USB disconnect, device number 4
usb 1-1.1: new high speed USB device number 5 using fsl-ehci
usb 1-1.1: config 1 interface 1 altsetting 0 bulk endpoint 0x5 has invalid maxpacket 16
usb 1-1.1: config 1 interface 1 altsetting 0 bulk endpoint 0x86 has invalid maxpacket 16
usb 1-1.1: device v1307 p0368 is not supported
scsi2 : usb-storage 1-1.1:1.0
scsi 2:0:0:0: Direct-Access Generic Storage Device 0.00 PQ: 0 ANSI: 2
sd 2:0:0:0: [sda] Attached SCSI removable disk
ehci_fsl_bus_resume begins, Host 1
ehci_fsl_bus_resume ends, Host 1
ehci_fsl_bus_suspend begins, Host 1
ehci_fsl_bus_suspend ends, Host 1
EXT4-fs (mmcblk1p1): re-mounted. Opts: errors=remount-ro,commit=0
ehci_fsl_bus_resume begins, Host 1
ehci_fsl_bus_resume ends, Host 1
warning: process `colord' used the deprecated sysctl system call with 8.1.2.
ehci_fsl_bus_suspend begins, Host 1
ehci_fsl_bus_suspend ends, Host 1
init: auto-serial-console main process ended, respawning
init: openvt main process ended, respawning
usb 1-1.4: new low speed USB device number 6 using fsl-ehci
usb 1-1.4: device v1bcf p0007 is not supported
input: USB Optical Mouse as /devices/platform/fsl-ehci.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input5
generic-usb 0003:1BCF:0007.0001: input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-fsl-ehci.0-1.4/input0
ehci_fsl_bus_resume begins, Host 1
ehci_fsl_bus_resume ends, Host 1
usb 1-1.3: new low speed USB device number 7 using fsl-ehci
usb 1-1.3: device v1241 p1603 is not supported
input: USB Keyboard as /devices/platform/fsl-ehci.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input6
generic-usb 0003:1241:1603.0002: input,hidraw1: USB HID v1.10 Keyboard [ USB Keyboard] on usb-fsl-ehci.0-1.3/input0
input: USB Keyboard as /devices/platform/fsl-ehci.0/usb1/1-1/1-1.3/1-1.3:1.1/input/input7
generic-usb 0003:1241:1603.0003: input,hidraw2: USB HID v1.10 Device [ USB Keyboard] on usb-fsl-ehci.0-1.3/input1
ehci_fsl_bus_suspend begins, Host 1
ehci_fsl_bus_suspend ends, Host 1